Telguard Digital TG-1 Quick Installation Manual

ANTENNA
LED MODE SELECT
J10
TELGUARD
Digital TG-1
T J7
BATTERY
(12V)
R
STC2
SYSTEM TROUBLE,
(N.C.)
STC (LED #2)
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
EARTH
3 FLASH = Not Used
GROUND
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
CAUTION:
REGISTRATION
INCORRECT CONNECTIONS
MAY RESULT IN DAMAGE TO UNIT.
(LED #1)
ON = UNIT REGISTERED
OFF = UNIT NOT REGISTERED
If flashing with LED 4 = DENIED ,
(NACK) www.Telguard.com
Call Technical Support.
REFER TO INSTALLATION AND OPERATING
If all LED's flashing = NO RESPONSE,
INSTRUCTIONS MANUAL. THIS DEVICE COMPLIES
Check Signal Strength.
WITH FCC RULE PART 15.

SYSTEM STATUS LEDS

RSSI MODE
RSSI Value LED's Lighted RF dBm
NO SVC LED 5*= flash, 4-2 = off n/a
1 LED 5 = on, 4-2 = off < -111 dBm
1 ½ LED 5 = on, 4 = flash, 3-2 = off > -110 dBm
2 LED 5-4 = on, 3-2 = off > -100 dBm
2 ½ > -90 dBm
LED 5-4 = on, 3 = flash, 2 = off
(Minimum Signal Recommended)
3 LED 5-3 = on, 2 = off > -80 dBm
3 ½ LED 5-3 = on , 2 = flash > -70 dBm
4 LED 5-2 = on > -60 dBm
*Note: LED 1 ON INDICATES MORE THAN ONE TOWER
SYSTEM STATUS LEDS
OPEN = NORMAL
SHORTED = RSSI
NORMAL MODE
LED #5 GREEN
ON = RADIO INITIALIZING
FLASH = COMMUNICATING
1
LED #4 RED
SIGNAL
2
ON = WAITING FOR RESPONSE
STRENGTH
3
If flashing with LED 1 = DENIED
(NACK)
4
LEDS
LED #3 YELLOW
5
OFF = MODE 2 (CELL Primary)
FLASH = C/C OFF HOOK CELL
LED #2 RED
SYSTEM TROUBLE, STC
(See Table)
LED #1 GREEN
REGISTRATION (See Table)
TELCO DIALER
AC
LED 6
BLANK PIN
AC
(12V 800MA)
HOST C/C
1 2 3 4 5 6 7 8 9
24 HOUR ZONE (N.C.)
TELULAR CORPORATION
420 Thornton Road, Suite 109
Lithia Springs, GA 30122
(800) 229-2326 Fax: 678-945-1651
TELGUARD DIGITAL TG-1

QUICK INSTALLATION GUIDE

INSTALLATION SUMMARY

There are four steps in installing Telguard properly. IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
Complete the Activation Form online at
to Telular Cellular Service prior to leaving for the job site.
S 1: L U M
TEP OCATE NIT AND
First, you will be confirming that Telguard has adequate cellular signal
strength. Put J10 across both pins, LEDS will now indicate signal strength,
minimum recommended is 2 ½ (2 on solid and the third flashing).
S 2: R T
TEP EGISTER ELGUARD
C R N
THE ELLULAR ADIO ETWORK
Next, you will be connecting the C/C's digital dialer output to Telguard and
verifying that alarm signals can be reliably sent through Telguard over
cellular to the central station digital receiver. The incoming Telco line is not
connected to Telguard during this step. A minimum of two alarm signals
must be transmitted.
(NOTE:
THE FIRST ALARM WILL REGISTER THE UNIT WITH THE
T C C
ELULAR OMMUNICATION
C ,
ENTRAL STATION ALL SIGNALS AFTER THE FIRST ARE SENT TO
C S )
THE ENTRAL TATION
S 3: C S
TEP ONNECT UPERVISORY
Next, you will wire Telguard's supervisory trip output to the C/C and then
test.
S 4: C I
TEP OMPLETE THE NSTALLATION
Your last step will be to check the jumper setting of J10 (LED mode, open =
normal), attach earth ground, and permanently mount the unit.
www.Telguard.com or fax the form
S S (RSSI)
EASURE IGNAL TRENGTH
& T C/C A
RANSMIT LARMS OVER
,
ENTER IT WILL NOT GO TO THE
T O
RIP UTPUTS
56034101