Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Prime Security AMX98
Summary of Contents for Prime Security AMX98
- Page 1 AMX98 (2) Rev. A - Installation Manual - Front Cover...
-
Page 3: Table Of Contents
Programming Table for Alarm Features ....15 Programming Table for Remote Controls ....16 AMX98(3) Rev. A - Installation Manual 12/98... -
Page 4: Important Information
This device complies with Part 15 of the FCC rules. Any changes or modifications made to the system without the express approval of Prime Security could void the made to the system without the express approval of Prime Security could void the user’s authority to operate this equipment. -
Page 5: Wiring Diagram
Wiring Diagram AMX98(3) Rev. A - Installation Manual 12/98... -
Page 6: 20 Pin Connector
Unlock Motor Side GREEN / RED Unlock Polarity (+) or (-) Input Select BLUE / BLACK Lock Switch Side Lock Motor Side BLUE / WHITE BLUE / RED Lock Polarity (+) or (-) Input Select AMX98(3) Rev. A - Installation Manual 12/98... -
Page 7: Installation Procedures
3. Using the long tie wraps supplied, securely fasten the impact sensor 3. Using the long tie wraps supplied, securely fasten the impact sensor allowing access to the adjustment screws. allowing access to the adjustment screws. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 8: Valet Switch
The LIGHT BLUE wire provides a 0.75 second (-) output when activated whether the alarm is armed or disarmed. If the remote control button is continually pressed, the signal will stay at ground as long as the button is held. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 9: Channel 6 Accessory (-) Output
(N.C.) starter disable. It is factory set for Normally Closed. NOTE: Make sure the YELLOW relay wires are solidly connected. The starter circuit may draw very high current. We recommend that all starter wire connections be soldered. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 10: Door Lock/Unlock
2. Press the remote arm/disarm button again within 3 seconds and the 2. Press the remote arm/disarm button again within 3 seconds and the passenger doors will unlock. passenger doors will unlock. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 11: Door Lock Diagrams
AMX98(3) Rev. A - Installation Manual 12/98... - Page 12 AMX98(3) Rev. A - Installation Manual 12/98...
- Page 13 AMX98(3) Rev. A - Installation Manual 12/98...
- Page 14 AMX98(3) Rev. A - Installation Manual 12/98...
-
Page 15: Hood/Trunk Pin Switch
8. Inspect all alarm wiring. Make sure all wires are connected. 9. Install the 5 amp fuse in the RED wire fuse assembly. 10. Install the 20 amp fuse in the RED/WHITE fuse assembly (if the vehicle parking lights are positive). AMX98(3) Rev. A - Installation Manual 12/98... -
Page 16: Programmable Features
6. Follow the "Secondary Action." You will hear a number of chirps to confirm that you have changed the setting of that feature. 7. Turn the ignition key "OFF." 8. Repeat steps 1-7 for any other feature you wish to program. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 17: Programming Table For Alarm Features
Wait 3 seconds, the siren will chirp Seconds once for 60 seconds, twice for 30. 30 or 60 seconds Wait 3 seconds, the siren will chirp Long-Term Silent Arm/Disarm once for Off, twice for On. AMX98(3) Rev. A - Installation Manual 12/98... -
Page 18: Programming Table For Remote Controls
Press ARM/DISARM button, the siren Control Code Learning Button will chirp 1 time. Wait 3 seconds, the siren will chirp Instant Remote Control — twice, all codes are erased out of Code Deletion memory. AMX98(3) Rev. A - Installation Manual 12/98... - Page 19 AMX98(3) Rev. A - Installation Manual 12/98...
- Page 20 AMX98 (2) Rev. A - Installation Manual - Back Cover...