Table of Contents
Advertisement
TABLE OF CONTENTS
A. SAFETY GUIDELINES...........................................................................................
B. INTRODUCTION....................................................................................................
List of parts.............................................................................................................
Step by step instructions........................................................................................
Floor level adjustment............................................................................................
Seat adjustment.....................................................................................................
Using the Handlebar Remote Control...................................................................
Understanding the Electronics Package...............................................................
Set.........................................................................................................................
Choosing between Program and Manual mode....................................................
Manual..................................................................................................................
Mode (What each of these categories means) ....................................................
INTERVAL.............................................................................................................
PROGRAM...........................................................................................................
Enter/Mode............................................................................................................
Reset.....................................................................................................................
Cleaning The Cycle...............................................................................................
Blank Display........................................................................................................
No Tension............................................................................................................
No "RPM" Reading...............................................................................................
Battery Removal and Installation Procedure........................................................
1
2
3
4
7
8
9
9
9
10
10
10
11
12
13
13
13
13
14
15
15
16
Advertisement
Table of Contents
Related Manuals for SPORTS ART 5002B
Summary of Contents for SPORTS ART 5002B
-
Page 1: Table Of Contents
TABLE OF CONTENTS A. SAFETY GUIDELINES................... B. INTRODUCTION....................C. ASSEMBLING YOUR CYCLE List of parts......................Step by step instructions..................Floor level adjustment.................... Seat adjustment..................... D. EXERCISING ON YOUR CYCLE Using the Handlebar Remote Control..............Understanding the Electronics Package............... Set......................... Choosing between Program and Manual mode............ Manual........................ -
Page 2: Safety Guidelines
Sports Art- 5002B/5002H Recumbent cycle SAFETY GUIDELINES: Please read and follow the following safety guidelines: . Read this owner's manual and follow the instructions. . Always unplug the cycle from the electrical outlet immediately after using and before cleaning . Assemble and operate the cycle on a solid, level surface. -
Page 3: Introduction
INTRODUCTION: Congratulations on purchasing one of the finest pieces of exercise equipment on the market today. Constructed of high quality materials and designed for years of troublefree usage, you will find the unit very easy to assemble and use. Before using your cycle, we recommend that you familiarize yourself with this Owner's Manual. -
Page 4: Assembling Your Cycle
ASSEMBLING YOUR CYCLE: List of parts: . Six 5/16"x 3/4" bolts Rear - cross tube support . Six 5/16" Spring washers Rea r- cross tube support . Six 5/16" flat washers Rear - cross tube support . Four 5/16"x 3/4" bolts - Handlebar mounting plate . -
Page 5: Step By Step Instructions
Step by step instructions Before assembling your cycle, make sure that you have all the above parts. The following steps explain how to assemble your exercise cycle. Please read every step thoroughly, and follow the directions completely to ensure correct assembly. 1. - Page 6 (FIG.2) 5. Insert the post seat back into the mounting plate and tighten securely using the screws and washers provided (see Fig. 3) (FIG.3)
- Page 7 Attach the seat base to the handlebar mounting plate, using the screws and washers provided. Insert the screws from underneath the seat--two in back and two in front, through the handlebar mounting plate. Tighten the screws securely (see Fig.4) (FIG.4) Attach the seat back adjustment handgrip to the seat back adjustment lever, using the wrench provided.
-
Page 8: Floor Level Adjustment
Floor level adjustment If the cycle is unsteady on your floor, turn the floor level adjustment either on the rear feet or at the front of cycle (see Fig.6). (FIG.6) -
Page 9: Seat Adjustment
Seat Adjustment Before your workout, you might need to adjust the seat to the appropriate position for your back or leg length. Sit on the cycle with both feet in the pedals and one leg extended as far as possible, pull up on the seat adjustment lvevr, and move the seat forward or backward until the pedal distance is comfortable. -
Page 10: Exercising On Your Cycle
EXERCISING ON YOUR CYCLE: Using the Handlebar Remote Control: For your convenience while your workout, the 5002H comes equipped with the remote control switch at the right end of the handlebars provide the same function as and Enter/Mode on the electronics package. Understanding the ELECTRONICS PACKAGE The electronics package lets you control your workout. -
Page 11: Choosing Between Program And Manual Mode
Choosing Between PROGRAM And MANUAL Mode: After your weight is set, the screen will read "MAN'L". Pressing an p key will scroll through "PRO 1 6", "MAN'L" and "INTV". Once you have set your desired program, then press Enter/Mode. MANUAL: You can use the Enter/Mode key to switch to LEVEL (or WATTS), PACER/RPM, DISTANCE, CAL., TIME, SCAN or PULSE. -
Page 12: Interval
LOAD (There are two expression of load): LEVEL: There are 14 levels, with Level 1 being the lightest, and LEVEL 14 being the heaviest. Use the keys to chose the desired level. WATTS: The watts range from 50-320 watts, with the watts 50 being the lightest, and the watts 320 being the heaviest. -
Page 13: Program
PROGRAM: 1. Use the keys to chose between Programs 1-6, then press "Enter/Mode" when they are displayed. When you press the Program of your choice, you must select either the DIST or the TIME. Use the key to set the desired distance or time. After you have set this, press "Enter/Mode". -
Page 14: Key Functions
KEY FUNCTIONS: DOWN: These keys are used to choose the desired TIME, DIST, MILE/KILO as well as to choose SET, MAN'L, INTV or PROGRAM In PROGRAM Mode, they are used to set the TIME or the DISTANCE. ENTER/MODE: After setting a preference, press these key to record and save your choice. -
Page 15: Trouble Shooting Blank Display
TROUBLE SHOOTING: A. Blank Display: 1. If you turn on the POWER switch and the switch is not lit: a. Check if the power cord is plugged securely into the wall socket. b. After the above step performed, if the power switch is still not lit, replace a new fuse. -
Page 16: No Tension
c. Plug the power cord into the wall socket and turn on the machine again. If the power switch is still not lit, please contact your dealer for more information.. 2. If you turn on the power and the switch is lit, but there is no display, please contact your dealer for more information. -
Page 17: Battery Removal And Installation Procedure
D. Battery Removal and Installation Procedure: To replace the batteries, remove battery cover, remove the spent batteries, then insert two new or recharged batteries, and replace cover (see Fig.9-10) (FIG.9) (FIG.10) - Page 18 Wiring Schematic:...