Flashing And Storm Collar Installation; Additional Requirements For Stainless Steel Vent Pipe Material; Exhaust Vent/Air Intake Connection To Boiler - Viessmann Vitocrossal 200 Installation Instructions Manual

Vitocrossal 200 CM2 186 to 311 Installation
General Venting Information

Flashing and storm collar installation

Flashings and storm collars are field supplied. Flashings
and storm collars suitable for Type B vent materials (or
better) may be used.
To obtain flashings and storm collars, please contact
your local vent material supplier. Follow the installation
instructions supplied by the special venting manufacturer.
Follow local codes to properly isolate the exhaust vent
pipe when passing through floors, ceiling and roof.
Always check the marking on the pipe to make sure you
are using the correct material.

Additional Requirements for Stainless Steel Vent Pipe Material

Use stainless steel venting system (UL/ULC listed for
category IV) for horizontal or vertical venting of the
Vitocrossal boilers.
Contact one of the suppliers (see listing on right) to order.
Prior to installation, check that the correct single-wall
vent parts were ordered and supplied.

Exhaust vent/air intake connection to boiler

The vent connection to the Vitocrossal boiler must be
made with the starter stainless steel adaptor (supplied
by others).
Combustion air intake, flex hose and adaptor must be
installed. If using room air-independent venting system,
connect the air intake pipe (from outdoors)to the adaptor
provided. If room air-dependent venting system is used,
the air is drawn into the burner inlet through adaptor and
flexible pipe. (See figure from page 11 and 16).
IMPORTANT
For exhaust vent pipe material:
Do not use any other vent material.
WARNING
The use of vent material other than listed UL/ULC
stainless steel and PPs positive pressure vent pipe and
fittings can cause property damage, severe personal
injury and/or loss of life.
(continued)
M&G / Duravent
Tel. 800-835-4429
Tel. 518-649-9700
Fax: 518-463-5271
Email: sales@duravent.com
Web: www.duravent.com
Selkirk Canada Corporation
375 Green Road
Stoney Creek, ON L8E 4A5
Tel.: (905) 662-6600
Fax: (905) 662-5352
(US) 1-800-992-8368
(Canada) 1-888-735-5475
Email: info@selkirkcorp.com
Web: www.selkirkchimney.com
Security Chimneys
International Ltd.
2125 Rue Monterey,
Laval, Quebec H7L 3T6
Tel. 450-973-9999
(US) 1-800-361-4909
(Canada) 1-800-667-3387
Fax: 450-973-2222
Email: infoeng@
securitychimneys.com
Web: www.securitychimneys.com
Wesmech Technical Sales
50 Ronson Drive, Suite 160
Toronto, ON M9W 1B3
Tel.: (416) 251-8990
Fax: (416) 251-8900
1-800-613-3789
Email: info@wesmechtech.com
Web: www.wesmechtech.com
Note: For SS venting system order transition adaptors
from the above mentioned suppliers.
Venting
ICC - Industrial Chimney Co.
400 J-F Kennedy,
St-Jerome, Quebec
Canada, J7Y 4B7
Tel. 514-565-6336
Fax: 514-565-6519
Email: sales@ICC-RSF.com
Novaflex
1-20 East Pearce St.,
Richmond Hill, Ontario,
Canada, L4B 1B7
Tel. 905-731-9411
Email: sales@flexmaster.com
Enervex Inc.
(formerly Exhausto)
Tel: 770-587-3238
Fax: 770-587-4731
(800) 225-2923
Email: info@exhausto.com
Web:www.vpstack.com
Van-Packer Co. Inc.
302 Mill Street
PO Box 307
Buda, IL 61314
Tel.: (309) 895-2311
Fax: (309) 895-3891
1-888-877-8225
Email: vpstack@theramp.net
Web:www.vpstack.com
33