AT&T CL82114 Quick Start Manual

Quick start guide
CL82114/CL82214/CL82314/CL82364/CL82414/
CL82464/CL82514
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
Plug the large end Plug one end of
of the telephone the telephone
base power line cord into a
adapter into a telephone jack
power outlet not or a DSL filter.
controlled by a
If you have DSL
wall switch.
high-speed Internet
service, a DSL filter
Route the power
(not included) is
adapter cord
required.
through this slot.
Route the
telephone line cord
Raise the antenna.
through this slot.
Plug the other end
of the telephone
line cord into the
Plug the small end of the
telephone jack on
telephone base power
the back of the
adapter into the power
telephone base.
adapter jack on the back of
the telephone base.
Caution: Use only the power adapter(s) provided with this product. To obtain a replacement,
www.telephones.att.com
visit our website at
1 (866) 288-4268
In Canada, dial .
Battery installation
Install the battery, as shown below. Charge your handset(s) before initial use.
The battery is fully charged after ten hours of continuous charging.
Step 1
Plug the battery connector securely into the socket inside the handset battery
compartment. Insert the supplied battery with the label THIS SIDE UP facing up,
as indicated.
Step 2
Align the cover flat against the battery compartment, then slide it upwards until
it clicks into place.
CHARGE light
Step 3
Charge the handset by placing it face forward in
the telephone base or charger. The CHARGE light
on the handset is on during charging.
Use only the supplied rechargeable battery or replacement battery (model
BT283342
).
Quick reference guide - handset
CHARGE light
On when the handset is
charging in the telephone base
or charger.
qCID/VOLUME
• Press qCID to show caller
ID log when the handset is
Charger installation
not in use.
• Press to scroll down while
Plug the power adapter
in menus.
into a power outlet not
• Press to decrease the
controlled by a wall
listening volume when on
switch. a call.
REDIAL/PAUSE
• Press repeatedly to view the
last ten numbers dialed.
• While entering numbers,
press and hold to insert a
dialing pause.
PHONE/FLASH
Press to make or answer
a call.
1
Press and hold to set or dial
your voicemail number.
TONE /a>A
• Press to switch to tone
1 (800) 222-3111
dialing temporarily
or call .
during a call if you have
pulse service.
• While entering names, press
to change the next letter to
upper or lower case.
/SPEAKER SPEAKER
Press to make or answer a call
using the speakerphone.
Handset
side view
BT183342/
pDIR/VOLUME
Press pDIR to show
•
directory entries when the
handset is not in use.
• Press to scroll up while
in menus.
• Press to increase the
listening volume when on
a call.
MENU/SELECT
• When the handset is not
in use, press to show
the menu.
• While in the menu, press to
select an item or save an
entry or setting.
OFF/CANCEL
• During a call, press to
hang up.
• While in a menu, press to
cancel an operation, back
up to the previous menu,
or exit the menu display; or
press and hold this button
to exit to idle mode.
QUIET# (pound key)
Press and hold to enter the
QUIET mode setting screen, or
to deactivate QUIET mode.
EQ
During an outside call,
intercom call, message or
announcement playback, press
to change the audio quality to
best suit your hearing.
MUTE/DELETE
• During a call, press to mute
the microphone.
• Press to delete digit
or character.
PUSH TO TALK
• Press to initiate a one-to-one or
one-to-group broadcast.
• Press and hold to broadcast to a group of
system handsets.
Quick reference guide - telephone base
/HANDSET LOCATOR Message counter
While the phone is idle, Shows the number of messages or other answering system
press to page all handsets. information.
IN USE indicator
• On when the handset is in use,
or when the answering system
is answering an incoming call.
• Flashes when another
telephone is in use on the
same line.
REPEAT
/
• Press to repeat a message.
• Press twice to play the
previous message.
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using the
telephone. Refer to the Handset settings and Answering system settings in
the Abridged user's manual or the online Complete user's manual for detailed
instructions on setting all telephone features.
Set date/time
Set the date/time before using the answering system.
1. MENU -> q or p -> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys -> SELECT.
3. Enter the hour and minute using the dialing keys.
4. q or p to choose AM or PM -> SELECT.
Basic answering system setup via voice guide
Your can follow the voice guide to record your own announcement, set the
number of rings, and set the message alert tone.
Using a cordless handset:
MENU -> q or p -> Answering sys -> SELECT.
1.
2. q or p -> Voice guide -> SELECT.
3. Set up your answering system by inputting the designated numbers,
as instructed.
/PLAY/STOP
Press to start or stop message
playback.
X/DELETE
• Press to delete the message
currently playing.
• Press twice to delete all old
messages when the phone is
not in use.
/ANS ON/OFF
Press to turn the built-in
answering system on or off.
SKIP
/
Press to skip a message.
qVOLUME and pVOLUME
• During message playback,
press to adjust the listening
volume.
• While in idle mode, press to
adjust the base ringer volume.