Zte MF60 Quick Start Manual

LEGAL INFORMATION
Copyright © 2012 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
ZTE MF60
photocopying and microfilm, without the prior written permission of ZTE
Corporation.
Quick Start Guide
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
Version No. : R1.0
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057 Tel: +86-755-26779999
URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn
1 2
Introduction Windows 7, Windows Vista(32bit or 64bit),
Operate system Windows XP (SP2 or later)
ZTE MF60 is a 3G/2G mobile hotspot device, working in GSM/GPRS/ MAC (10.4 or later)
EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to
IE (7.0 or later), Firefox (2.0 or later), Opera (10.0
it via USB or Wi-Fi interface. The device supports data and SMS services,
Web Browser or later), Safari (4.0 or later), Chrome (5.0 or
enabling you to communicate anytime and anywhere.
later)
This manual provides instructions on how to install and get started with the
Operating temperature 0 °C ~ +35 °C
product. For information about connection of services, please consult your
service provider.
Storage temperature -20 °C ~ +50 °C
Specification
Charging temperature 0 °C ~ +45 °C
Humidity 5%~ 95%
HSPA+: DL 21.6 Mbps,
UL 5.76 Mbps Notes:
Data Service
WCDMA CS: 64 kbps UL/DL microSD is a trademark of SD Card Association.
The device's standby and working time are only for your reference, and
WCDMA PS: 384 kbps UL/DL
based on ideal working environment.
Interface USB and Wi-Fi
Getting to Know Your Device
Wi-Fi Standard 802.11b/g
The following figure shows the appearance of the device, it is only for your
Wi-Fi Security WEP/WPA/WPA2/WAPI
reference. The actual device may be different.
USB Version USB 2.0 HIGH SPEED
USB Interface Type Micro USB
Weight 86 g
Dimensions (W×H×D): 99.6 mm*54 mm*14.6 mm
microSD card Support up to 32 GB microSD card
Power Adapter 5 V/700 mA
Battery 1500 mAh
*Standby time 100 hours
*Working time 4 hours Right Side Front Left Side
3 4
Interface and Buttons
Connect to the Internet manually.
1. Power Button Hold the Power button to switch on/off the device.
Roaming network indication.
2. Memory card slot It is where you insert the memory card (microSD
(microSD card) card).
New message received.
3. WPS Button
Indicates Wi-Fi status and the number of the connecting users.
It indicates the network type, signal strength,
4. LED Screen
battery status, and Wi-Fi, etc.
Indicates the battery status.
5. External Antenna It is used to connect an external antenna to
Hardware Installation
Port enhance the signal strength.
• Charge your device.
6. Charger/USB port
Inserting SIM Card and Battery
• Connect the client to your device via USB cable.
1. Slide the back cover and remove it.
Notes:
• Hold the WPS and Power buttons simultaneously until the LED
screen turns off, and then release the buttons. The device will restart
automatically and restore to the factory default settings.
• Please use the original external antenna if necessary.
LED Indicator
When the device is powered on, the following icons will appear on the LED
screen, with the corresponding indicates listed in the table below: 2. Insert the SIM card into the SIM card holder.
Icon Indication
Indicates the network signal strength.
Indicates the network type. 2G or 3G icon will appear on the
LED screen according to the network being connected.
Connect to the Internet automatically.
Bottom
5
3. Insert the battery as shown with the contacts located against the metal Switching On/Off Your Device
springs, and press the battery down into the case.
Hold the Power button to switch on/off the device.
Notes:
The device is powered on when the LED screen lights up.
Charging Your Device
You can charge your device by using USB cable or adapter.
1. Insert the charger lead carefully.
2. The plug only fits one way. Do not use excessive force to insert the plug.
4. Slide the back cover and lock the cover in its place.
Inserting microSD Card
1. Pull the microSD cover out of the card slot.
Your device supports three working modes. For the client, we only use PC or
Notes:
laptop as the example in this document.
Do not pull the cover rudely, as it is connected with the device.
USB Mode: Connect to the device with the USB cable.
2. Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
3. Close the microSD cover.
6 7
Wi-Fi Mode: Connect to the device via Wi-Fi.
Mixed Mode: Connect to the device with the above two connection methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure that
the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices can
surf on the Internet at the same time.
Working Mode
Establish a connection between your device and
the client
Via USB Cable
1. Connect your device and the client with the USB cable.
2. Power on your device.
3. Follow the system prompts to complete the software installation.
8 9