1. Manuals
  2. Brands
  3. Sharp Manuals
  4. All in One Printer
  5. MX 5500N - Color Laser - Copier
  6. Installation manual

Sharp MX-5500N Installation Manual

Digital full color multifunctional system
Hide thumbs Also See for MX-5500N:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Troubleshooting Manual, Instructions for Use Manual
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
[ 1 ] MX-5500N/6200N/7000N (Main unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 2 ] MX-LCX2 (Large capacity tray (A4)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[ 3 ] MX-LCX3 (Large capacity tray (A3)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[ 4 ] MX-RBX2 (Paper pass unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[ 5 ] MX-CFX1 (Inserter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[ 6 ] MX-PNX2A/B/C/D (Punch module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[ 7 ] MX-FNX3 (4K finisher) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[ 8 ] MX-FNX4 (4K Saddle stitch finisher). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[ 9 ] MX-FRX3, MX-FRX3U (Data security kit). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] MX-PKX1 (PS3 expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] AR-PF1 (Barcode font kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1
[12] MX-AMX1 (Application integration module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[13] MX-FXX1 (Facsimile expansion kit). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
[14] MX-FWX1 (Internet Fax expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
INSTALLATION MANUAL
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MODEL
CONTENTS
SHARP CORPORATION
CODE: 00ZMX7000/I1E
MX-5500N
MX-6200N
MX-7000N
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

Advertisement

Table of Contents
loading

Related Manuals for Sharp MX-5500N

Summary of Contents for Sharp MX-5500N

  • Page 1: Table Of Contents

    [ 1 ] MX-5500N/6200N/7000N (Main unit) ........

  • Page 2: Configuration

    Punch module (MX-LCX2) Inserter (MX-PNX2A/B/C/D) (MX-CFX1) Digital full color multifunctional system Paper pass unit (Copier/Printer/Scanner) (MX-RBX2) Large capacity tray A3 (MX-5500N) (MX-LCX3) (MX-6200N) (MX-7000N) Staple cartridge Saddle stitch finisher (AR-SC3) (MX-FNX4) Data security kit Barcode font kit PS3 expansion kit...
  • Page 3 B. Machine configuration Copier memory (Local memory) (MB) Printer memory (System memory) (MB) 896MB Copier Standard provision PCL printer Standard provision PS printer Option (Product key target.) Main body LCD Color VGA 10.4" Option (No support for some areas.) Scanner Standard provision Filing Standard provision...
  • Page 4 Temperature: 10 to 35°C ±2%. If power waveform is deformed, a trouble may occur. Humidity: 20 to 85% RH (4) Safety Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m) Be sure to properly ground the machine. MX-7000N MX-5500N/6200N/7000N 1 – 1...

  • Page 5: Transit And Delivery

    Copy quality may be adversely affected and a trouble may be caused. (5) Vibration Avoid installation near a machine which produces vibrations. If vibrations are applied to the copier machine, copy images may be deflected and a trouble may be caused. MX-7000N MX-5500N/6200N/7000N 1 – 2...
  • Page 6 Lift the main unit slightly, and remove the bottom pad L. * Slope : Deal as a parts. Part name Part code Skid slope DKiT– 0367FCZZ Attach the slope to the concave section of the skid. MX-7000N MX-5500N/6200N/7000N 1 – 3...
  • Page 7 D. Check the packed items Check that all the items are included in the package. Names of bundles Quantity Waste toner bottle Paper exit tray Paper exit full detection actuator Operation manual pocket Operation manual MX-7000N MX-5500N/6200N/7000N 1 – 4...
  • Page 8 NOTE: If the machine is left unused for one month or more, the heat roller rubber may be deformed. In such a case, release the pressure by pushing up both levers. Attach the removed fixing material to the position shown in the figure for storage. MX-7000N MX-5500N/6200N/7000N 1 – 5...
  • Page 9 Pinch the knob and remove the development unit. Hold the drum fixing knob by the hand to not rotate, remove the screw, and remove the drum fixing knob. Remove two fixing screws of the DV cover. Pull out the fixing cover. MX-7000N MX-5500N/6200N/7000N 1 – 6...
  • Page 10 12) Fix the DV cover with the two screws. drop developer on the drive section (marked with 13) Shake the development unit horizontally a few times. * When supplying developer, do not tilt the development unit. MX-7000N MX-5500N/6200N/7000N 1 – 7...
  • Page 11 Disconnect the connectors on front side and rear side. 15) Fix it with the fixing screw. D. Infusing the developer (black) Loosen the fixing screw. While rotating the MG roller, infuse the developer. Hold the knob and remove the development unit. MX-7000N MX-5500N/6200N/7000N 1 – 8...
  • Page 12 Engage the pawls to the toner hopper unit, and install it, and fix with the screws. 11) Close the cover of the process section. Shake the development unit horizontally a few times. 12) Tighten the screws. Push the fixing cover. MX-7000N MX-5500N/6200N/7000N 1 – 9...
  • Page 13 Paper exit full detection actuator IL interface harness Screw (S tight M4x8) (2) Installation of the IL interface harness Remove the screw, and remove the switch cover. Check that the waste toner bottle is installed securely. MX-7000N MX-5500N/6200N/7000N 1 – 10...
  • Page 14 Install the paper holding arm (Package part No. 2), and install the paper exit full detection actuator (Package part No. 3). * Check the size of the diameter of place where paper holding arm is installed. MX-7000N MX-5500N/6200N/7000N 1 – 11...
  • Page 15 AT DEVE ADJ_L_M AT DEVE VO_M_M AT DEVE ADJ_L_Y AT DEVE VO_M_Y AT DEVE ADJ_M_K AT DEVE VO_H_K AT DEVE ADJ_M_C AT DEVE ADJ_M_M AT DEVE ADJ_M_Y AT DEVE ADJ_H_K AT DEVEVO_L_K AT DEVEVO_L_C AT DEVEVO_L_M EXECUTE MX-7000N MX-5500N/6200N/7000N 1 – 12...
  • Page 16 J. Installation of the operation manual pocket * Be sure to insert all of five toner cartridges (Y/M/C/BK1/ Install the operation manual pocket (Package part No. 4) to the BK2). back side of the machine. [Color toner cartridge positions] MX-7000N MX-5500N/6200N/7000N 1 – 13...
  • Page 17 Fixed Paper Side Disable Duplex Disable Staple Disable Punch Copy Print I-Fax Doc. Filing Type Plain Tray 4 Change Size Auto-Inch Fixed Paper Side Disable Duplex Disable Staple Disable Punch Copy Print I-Fax Doc. Filing MX-7000N MX-5500N/6200N/7000N 1 – 14...
  • Page 18 * Double the sheet, and install it. * Be careful to place and direction that install the sheet. b. A4-B5 series tray 1 (A4 to B5) * Except Europe, Australia, and New Zealand Pull out the tandem cassette. MX-7000N MX-5500N/6200N/7000N 1 – 15...
  • Page 19 Remove the screw, and remove the mylar sheet. Change the installing direction and install with screws. (2 positions) 11) Attach the A4 size regulation plate to inner side of the waste toner bottle section cover. MX-7000N MX-5500N/6200N/7000N 1 – 16...
  • Page 20 (PLEASE USE SPECIFIED TYPE OF A3 OR 11" 17" SIZE PAPER FOR THIS ADJUSTMENT) EXECUTE Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically selected.) The color patch image (adjustment pattern) is printed out. MX-7000N MX-5500N/6200N/7000N 1 – 17...

  • Page 21: Auto Adjustment

    The color patch image (adjustment pattern) is printed out. Note: Do not cancel the simulation until "PLEASE QUIT THIS MODE" is displayed. CLOSE SIMULATION NO. 46-24 TEST ENGINE HALFTONE AUTO ADJUSTMENT COMPLETED THIS PROCEDURE. PLEASE QUIT THIS MODE. MX-7000N MX-5500N/6200N/7000N 1 – 18...
  • Page 22 • If the data are kept, the setup values and the adjustment values can be entered without adjustments, shortening the servicing CLOSE SIMULATION NO.67-24 TEST time. PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE COMPLETED THIS PROCEDURE. PLEASE QUIT THIS MODE. MX-7000N MX-5500N/6200N/7000N 1 – 19...
  • Page 23 Lock the following sections. • Scanner (Optical section) • Paper cassette lift plate NOTE: Since the hard disk drive is built in the machine, use care not to exert vibrations or shocks to the machine when in transit. MX-7000N MX-5500N/6200N/7000N 1 – 20...
  • Page 24 [2] MX-LCX2 Pull out gently the large capacity tray until it stops. MX-7000N Service Manual 1. Unpacking A. Pulling out of the large capacity tray (A4) unit Pull out the large capacity tray (A4) unit. Remove the paper feed base fixing screw (1 pc.) of the large capacity tray.
  • Page 25 C. Check the packed items Disconnect the power plug of the main unit from the power out- let. Check that all the items are included in the package. Names of bundles Quantity Mounting plate upper B. Attach the mounting plate upper and the lower Connecting plate lower front Connecting plate lower rear front/rear connecting plate...
  • Page 26 Release the lock, and open the right door. Remove the fixing screws (2 pcs.) of the machine entry port, and remove the entry port cover. Attach the entry port cover reversely to the machine and fix it with the two fixing screws which was removed in procedure 3). * When working, be careful to prevent damage of the paper pass (transport) surface on the entry port cover.
  • Page 27 10) Close the right door. At that time, pull the large capacity tray in a right direction and check that a large capacity tray is locked to the main body. C. Attach of the large capacity tray to the main unit Hold the grips of the front and the rear cabinets with both * If lock is incomplete, when the power switch is turned on, the...
  • Page 28 <<How to separate the large capacity tray from the main R side unit>> Turn the lock release screw of the front cover clockwise and tighten the screw securely to release lock. E. Connector connection Remove the fixing screws (one for each) from the connector cover on the main unit and then remove the two connector covers.
  • Page 29 Loosen the stopper fixing screw (1 pc.) on the lower right side of the paper feed tray to disable the stopper function. F side R side b. Auxiliary guide size switch Then pull out the paper feed tray again until it stops. When changing the size of the side plate R, check to confirm the mark positions of "...
  • Page 30 G. Turn ON the main power switch of the main Tighten the removed rear edge shaft with the fixing screw (blue), and store it in the storage space inside the front cabi- unit net. Connect the power plug of the main unit into the power outlet. Open the front cabinet of the main unit.
  • Page 31 H. Size setting [When shifted to the front side] To adjust the print line in the direction A from the paper center as Execute SIM 26-2 "Size setting" with the key operations of the main shown in the figure, increment the number of value. Then make a unit.
  • Page 32 Loosen the stopper fixing screw (1 pc.) on the lower right side Push the large capacity tray slowly into the original position. of the paper feed tray to disable the stopper function. Then make a copy to check to insure that there is no more shift. Repeat the procedures until there is no shift.
  • Page 33 [3] MX-LCX3 Manually pull out the cassette. MX-7000N Service Manual Push the shaft at the rear side of the front cabinet to release the lock. (About 5mm) 1. Unpacking A. Pulling out of the large capacity tray (A3) unit Pull out the large capacity tray (A3) unit. * When the lock is released, be careful the spring will push out the cassette about 50mm.
  • Page 34 C. Check the packed items Remove the fixing screws (3 pcs.) of the paper feed table of the LCC, and remove the cautionary note A. Check that all the items are included in the package. Note: When the power is turned on without removing the fixing screw, remove the fixing screw and execute SIM 15.
  • Page 35 Open the front cabinet of the main unit. Turn OFF the power Release the lock, and open the right door. switch in the front cabinet. "OFF" Disconnect the power plug of the main unit from the power out- let. Remove the screws, and remove the upper cover. B.
  • Page 36 Remove the two fixing screws of the machine entry port, and 10) Close the right door. remove the entry port cover. Attach the entry port cover reversely to the machine and fix it with the two fixing screws which was removed in procedure 3. * When working, be careful to prevent damage of the paper pass (transport) surface on the entry port cover.
  • Page 37 a. When the height is properly adjusted: b. When the height is not properly adjusted: When both the edges of the connecting plates on front and Use the adjustment device on the lower left side of the LCC to rear are fit with the longest mark on the mounting plates each, adjust the height of the left caster section.
  • Page 38 <2> c. If the upper section of the LCC left side is locked first Turn the adjustment screw above to adjust the height. and the positioning plate cannot be inserted : After adjustment with the adjustment screw, tighten the screws on the both ends of the caster movable plate which were loos- ened in the previous procedure.
  • Page 39 Front side - When the upper side is not locked Raise the adjuster on the lower side of the LCC right side until the hole shown in the figure below comes at the center, and check that it is locked. * If lock is incomplete, when the power switch is turned on, the message, "Check installation of tray 5"...
  • Page 40 [How to separate the LCC from the machine] Push the resin cover beneath the lock section on the top of the left side of the LCC and shift the LCC to the right. Release the Remove the left front cabinet of the LCC. top lock.
  • Page 41 E. Select the paper size Rear edge plate size changeover <1> Slowly pull out the paper feed base tray until it stops. Lift the MC-CL handle at the top of the rear edge plate and shift it to the desired paper size position. <2>...
  • Page 42 Open the front cabinet of the main unit. Turn ON the power Item Default switch in the front cabinet. BK-MAG Main scan print magnification ratio BK Print off-center adjustment value (Manual paper feed) Print off-center adjustment value (Tray 1) Print off-center adjustment value (Tray 2) Print off-center adjustment value (Tray 3)
  • Page 43 (2) Mechanical adjustment-1 <3> Push the large capacity tray slowly into the original position. Since the off-center adjustment has been made at shipping, there is normally no need to adjust. If the center is shifted, however, adjust with the simulation. If the shift is not recovered, perform the following steps to adjust.
  • Page 44 <3> Set a sheet of paper on the paper feed base tray. Check that Push the large capacity tray slowly into the original position. the front regulation plate is at the marked center, and push it in contact with the front regulation plate. Loosen the blue screws of the rear regulation plate.
  • Page 45 b. Diagonal feed adjustment [In the case of diagonal feed 2] Press the lock button on the front cabinet and lower the paper Loosen the blue screw (A) on the front regulation plate. feed base tray to the paper supply position. Pull out the tray. Referring to the degree of diagonal feed, move the regulation plate in the direction of (+) and fix the blue screw.
  • Page 46 [4] MX-RBX2 MX-7000N Service Manual 1. Unpacking C. Check the packed items A. Pulling out of the paper pass unit Check that all the items are included in the package. Pull out the paper pass unit. B. Removal of the protection material Names of bundles Quantity Remove the fixing tape.
  • Page 47 2. Installation Remove the toner cartridge. <Note before installation> * Before starting installation, check to insure that the data lamp on the operation panel does not light up or blink. A. Turn OFF the power of the main unit Turn OFF the power switch on the operation panel. "OFF"...
  • Page 48 E. Installation of the reverse detection lever D. Installation of the short-circuit harness Install the reverse detection lever (Package part No. 6). * As for the following procedures, only destinations other than North America, Australia, and New Zealand are required. For * Be careful of the installing direction of the reverse detection North America and Australia, New Zealand, progress to the pro- lever.
  • Page 49 Fix the right rail with the fixing screw (Package part No. 1). Fix the reverse tray with the hand screw (Package part No. 3) while holding it to upper direction. I. Installation of the paper pass unit G. Installation of the left rail Pull out the slide rails.
  • Page 50 K. Installation of the toner cartridges Insert the upper front cover (Package part No. 12) to the sup- porting point, and fix it with a E-ring (Package part No. 4). Install the toner cartridges. Close the upper front cover. Fix the wire with fixing screws (Package part No. 2). J.
  • Page 51 [5] MX-CFX1 MX-7000N Service Manual 1. Unpacking A. Removal of the inserter B. Removal of the protection material * For removal of the inserter, manpower of two persons or more is Remove the fixing tapes and protection material. required. Remove the packing cushion, and bundled items from packing cusion.
  • Page 52 2. Installation Open the top door, and remove the fixing tape and protection material. <Note before installation> * Before installing the MX-CFX1, unpack the MX-FNX3 or MX- FNX4. A. Installation of the FIN connection fixture A/B Fix the FIN connection fixture B (Package part No. 7) to the FIN connection fixture A (Package part No.
  • Page 53 C. Connection of the inserter and finisher (Punch • Connection fixture F/R for MX-FNX3 (Screw used for installation : Package part No.3 of MX-FNX3) unit) Attach the inserter to the finisher (or Punch unit). * Match the sign of the inserter to connection plate, and engage the inserter.
  • Page 54 Close the front cover of the finisher (or Punch unit). Install the rear cover of the finisher (or Punch unit) with the fix- ing screws. Remove the screws on rear side of the finisher (or Punch unit), and remove the rear cover. D.
  • Page 55 E. Installation of the rail F. Check of the connected position of main unit and finisher. Engage the inserter that has installed finisher (Punch unit) to the main unit. Put the inserter that has installed the finisher (Punch unit) close to the main unit. Release the lock, and remove the inserter from the main unit.
  • Page 56 Turn the height adjustment bolt on the rear side so that the Turn the height adjustment screws on the front side so that the height of the center of the positioning pin and the center of the fixing screw of the adjustment section on the front side may positioning guide is fit.
  • Page 57 Check the height of rear cabinet of the inserter and rear cabi- <Adjust of the height on rear side> net of the finisher. Remove the rear cabinet of the finisher, and loosen the rear caster fixing screws on the inserter side. Rear * When the height is properly adjusted, progress to the proce- dure of "H.
  • Page 58 H. Check the clearance of the main unit and the Remove each cabinet on the front and the rear side of the fin- isher, and loosen the fixing screws of the front and rear caster inserter on the left side. Put the inserter that has installed the finisher (Punch unit) * The adjustment procedure is different according to the close to the main unit.
  • Page 59 Tighten the fixing screws of the front and rear caster on the left Touch the auxiliary caster to the floor, and tighten the caster side, and attach each cabinet on the front and the rear side of fixing screws so that the indicator scale is fit. the finisher.
  • Page 60 K. Connection of connector to the main unit Open the front cabinet of the main unit. Turn ON the power switch in the front cabinet. Connect one of the two connector of the finisher to the main body and connect one of another to the inserter, and tighten each screws.
  • Page 61 [6] MX-PNX2A/B/C/D Open the front cover, and open the top cover. MX-7000N Service Manual 1. Unpacking A. Pulling out of the punch unit Pull out the punch unit. Remove the screws, and remove the fixing material. (2 posi- tions) B. Removal of the protection material Remove the fixing tape and protection material.
  • Page 62 C. Check the packed items Attach the step screw A (Package part No. 2) to the finisher. Check that all the items are included in the package. Remove the fixing screw, and remove the connector cover on rear side of the finisher. MX-FNX4 only Names of bundles...

  • Page 63: Punch Unit

    B. Connection of connector of the finisher and Attach the front cover mounting fixture (Package part No. 6) with the fixing screws (Package part No. 3). punch unit • In the case of the saddle stitch finisher (MX-FNX4) Remove the fixing screws, and remove the rear cover. Install it using three fixing screws (Package part No.
  • Page 64 Install the Connection fixture R (Package part No. 8) to the Check that the center of the screw hole of the punch unit is in main unit with the fixing screws (Package part No. 4). the range of specification of an oval hole of the mounting fix- ture in front side of main unit.
  • Page 65 Fix the main unit and the punch unit with the fixing screw By using nippers, split the removed connector cover of the fin- (Package part No. 4 of MX-FNX3 or MX-FNX4). isher along the perforated line. Close the front door of punch unit. Install the connector cover of the finisher and fix it with the fix- ing screw.
  • Page 66 I. Punch position label attachment J. Turn ON the main power switch of the main unit Attach the punch position label to the position indicated in the figure. Connect the power plug of the main unit into the power outlet. [For scanner] (Package part No.
  • Page 67 [7] MX-FNX3 MX-7000N Service Manual Remove the skid and packing cushions. 1. Unpacking A. Removal of the finisher * For removal of the finisher, manpower of two persons or more is required. Remove the fixing material, and remove the top case. Remove the bundled items from packing cushion.
  • Page 68 B. Removal of the protection material C. Check the packed items Remove the fixing tapes and protection material. Check that all the items are included in the package. Names of bundles Quantity Binding head round tapping M4x8 IT tapping M4x20 Binding head M4x12 Open the front upper door, and remove the fixing tapes and Step screw B...
  • Page 69 A. Installation of the rail Install the connection fixture F (Package part No. 7) to the main unit with the fixing screws (Package part No. 3). Install the rail (Package part No. 5) to the finisher with the fix- ing screws (Package part No. 1). Install the rail reception sheet metal (Package part No.
  • Page 70 Check that the center of the screw hole of the finisher is in the Open the front upper door. range of specification of an oval hole of the connection fixture that exist on main body rear side. Remove the screws, and open the front lower door. * When not the range of specification, execute the following adjustment.
  • Page 71 Remove the fixing tapes. 10) Turn the bolt for which the adjustment is necessary, and adjust to become it within the range of specification. Loosen both of the caster fixing screws of the front side and rear side. 11) Check to insure that the upper and lower clearances between the main unit and the finisher are even.
  • Page 72 12) Tighten the caster fixing screws so that the indicator scale is 15) Close the front lower door, and fix with the fixing screws. fit. 16) Close the front upper door. 13) Install the rear lower cover with the fixing screws. 17) Attach the front lower cover with the fixing screws.
  • Page 73 Open the front cover of finisher. Install the Step screw B (Package part No. 4). Fix the finisher to the main unit with the step screw B (Package Attach the connector cover on rear side of the finisher. part No. 4). Close the front cover.
  • Page 74 G. Staple position label attachment H. Turn ON the main power switch of the main unit Attach the label to the position indicated in the figure. [For scanner] (Package part No. 9) Connect the power plug of the main unit into the power outlet. Edge of R part in corner Reference line of Edge of R part in corner...
  • Page 75 [8] MX-FNX4 MX-7000N Service Manual Remove the skid and packing cushions. 1. Unpacking A. Removal of the saddle stitch finisher * For removal of the saddle stitch finisher, manpower of two per- sons or more is required. Remove the fixing material, and remove the top case. Remove the bundled items from packing cushion.
  • Page 76 B. Removal of the protection material Remove the screws and remove the fixing material for paper exit tray. (four positions) Remove the fixing tapes and protection material. Open the front door of the finisher, and remove the fixing tapes and protection material. Pull out the stapler unit.
  • Page 77 C. Check the packed items Replace the stapler unit to the original position, and close the front door. Check that all the items are included in the package. Remove the fixing screws, and remove the right lower cover. Remove the fixing screws, and remove the pressure release plates of saddle section.
  • Page 78 2. Installation Install the connection fixture F (Package part No. 7) to the main unit with the fixing screws (Package part No. 3). <Note before installation> * When the MX-FNX4 is installed, first install the MX-RBX2, and then install the MX-FNX4. * When the MX-FNX4 and MX-PNX2 is installed at the same time, first install the MX-PNX2, and then install the MX-FNX4.
  • Page 79 Check that the center of the screw hole of the finisher is in the Remove the cabinet fixing screw. range of specification of an oval hole of the connection fixture that exist on main body rear side. Remove the screw, and remove the front lower cabinet 1. Remove the fixing screw of the front lower cabinet 2.
  • Page 80 Remove the screws, and remove the rear lower cover. 10) Remove the screw, and remove the spanner installed inside the front door. 11) Turn the bolt for which the adjustment is necessary, and adjust to become it within the range of specification. Remove the fixing tapes.
  • Page 81 13) Tighten the caster fixing screws so that the indicator scale is 16) Install the front lower cabinet 1 with the fixing screws. fit. 17) Attach the cabinet fixing screw. 14) Install the rear lower cover with the fixing screws. 18) Install the spanner for adjustment to inside the front door with screw.
  • Page 82 E. Connection of the saddle stitch finisher Close the front cover. Engage the saddle stitch finisher to the main unit. Remove the screw, and remove the connector cover on rear side of the finisher. Open the front door of saddle stitch finisher. Install the Step screw B (Package part No.
  • Page 83 F. Connection of connector to the main unit H. Turn ON the main power switch of the main unit Connect two connectors of the saddle stitch finisher to the main unit, and tighten the screws. Connect the power plug of the main unit into the power outlet. Open the front cabinet of the main unit.
  • Page 84 [9] MX-FRX3, MX-FRX3U After checking that the operation panel has gone out, open the MX-7000N Service Manual front cabinet and turn the main power switch to the "OFF" posi- tion. 1. Unpacking A. Check the packed items Check that all the items are included in the package. "OFF"...
  • Page 85 Remove the screws of control box. Raise the finger handle, Pull out the control box until the position in which the connector and pull out the control box slowly. of the HDD-IDE cable is seen. Pull the sheet, and remove the HDD-IDE cable.
  • Page 86 F. Installation of the rear cabinet upper Remove the seven screws that fixing the rear cabinet upper. Remove the rear cabinet upper. Install the fold section of upper side on the rear cabinet upper to the main unit. Secure it with the seven screws that have been removed in step D-3).
  • Page 87 H. Turn ON the power switches of the main unit * If the fax box unit is installed, carry out the steps 3). Connect the I/F cable to the MFP PWB. Push the I/F cable into Insert the power plug of the main unit to the power outlet. the recessed portion of the sheet metal on the control box.

  • Page 88: Operation Check

    (Cyan)], set to the [Bk (Black)] with full color mode, then copy the blank paper with B/W mode. Use the specified A4 paper by SHARP, be sure to don't use the back print paper. Set on the document table the each paper that printed by procedure b), and copy it.

  • Page 89: Mx-Pkx1 (Ps3 Expansion Kit)

    [10] MX-PKX1 MX-7000N Service Manual 1. Unpacking A. Check the packed items Names of bundles Quantity CD-ROM (For Screen Font) Product key sheet NOTE: To set up the PS driver, do not use the CD-ROM (Package part No. 1) which is included in the MX-PKX1 but use the CD-ROM which is included in the MX-PBX1.

  • Page 90: Ar-Pf1 (Barcode Font Kit)

    [11] AR-PF1 Disconnect the power plug of the main unit from the power out- MX-7000N Service Manual let. 1. Unpacking A. Check the packed items AR-PF1 barcode font ROM PWB B. Removal of the control box * If cables are connected to the control box, remove all cables. Names of bundles Quantity Remove the screw of right rear cabinet, push down the right...
  • Page 91 C. Installation of the barcode font ROM PWB Hold the snap band to arrow direction, and remove it, and remove the I/F cable. Install the barcode font ROM PWB to the barcode connector. * Check to confirm that the silver push lever extends out when the PWB is installed.
  • Page 92 E. Turn ON the main power switch of the main * If the fax box unit is installed, carry out the steps 3). unit Connect the I/F cable to the MFP PWB. Push the I/F cable into the recessed portion of the sheet metal on the control box. Insert the power plug of the main unit into the power outlet.
  • Page 93 G. Font list Font Font name Font Font name Code128TT-Regular OCR-A Code128-NarrowTT- OCR-B Regular Code128-WideTT- OCR-B-C39-Regular Regular Code39HalfInch-Regular Upc-Half Code39OneInch-Regular Upc-Half-Bars Code39QuarterInch- Upc-HalfMusic Regular Code39SmallHigh- Upc-HalfNarrow Regular Code39Slim-Regular Upc-HalfThin Code39SmallLow- Upc-Tall-Regular Regular Code39SmallMedium- Upc-TallBarsThin-regular Regular Code39Wide-Regular Upc-TallMusicThin- Regular Codabar-Regular Upc-TallNarrow-Regular Interleaved2of5-Regular Upc-TallThin-regular Interleaved2of5-Thin-...

  • Page 94: Mx-Amx1 (Application Integration Module)

    [12] MX-AMX1 MX-7000N Service Manual 1. Unpacking A. Check the packed items Names of bundles Quantity CD-ROM MX-AMX1 GETTING STARTED GUIDE Sharpdesk license kit Operation Manual 2. Installation <Note before installation> * To enable the Application Integration Module function, the prod- uct key must be acquired.

  • Page 95: Mx-Fxx1 (Facsimile Expansion Kit)

    [13] MX-FXX1 * The fax box unit without the mark “N” for identification includes MX-7000N Service Manual only the step screw (Package part No.3) not for installation. Therefore, when installing, prepare the service parts (LX- 1. Unpacking BZ1088FCZZ) in advance. The fax box unit with the mark for identification includes the step A.
  • Page 96 "OFF" Disconnect the power plug of the main unit from the power out- let. B. Installation of fax box unit Remove the two screws from the rear cabinet of the main unit. Attach the supplied step screw A (Package part No. 2) to one of the two positions from which the screws are removed.
  • Page 97 C. Removal of the control box D. Attach the FAX memory Remove the screw of right rear cabinet, push down the right Install the FAX memory (Package part No. 4) to the socket on rear cabinet. Disengage the pawls, and remove the right rear the MFP PWB as shown in the figure below so that the mem- cabinet so that slide to the front side.
  • Page 98 Connect the I/F cable to the MFP PWB. Push the I/F cable into Push into the cable to the right cabinet rear cover, and attach the recessed portion of the sheet metal on the control box. it. At this time, check that the pawls are properly fitted to the main unit.
  • Page 99 H. Set the destination and the logo type Use numeric keys [0] and [1] to enter the desired 8-digit coun- try code. Switch the operation panel to the copy mode and use the key After entry, press [SET], [EXECUTE], and [YES] in this order. operation [P], [∗], [C], and [∗] to enter the simulation mode.
  • Page 100 Use the numeric keys to enter [10] in the sub-code entry screen shown below and press the [START] key. FAX SOFT SW. SETTING. FAX SOFT SW. CLEAR. FAX PWB MEMORY CHECK. SIGNAL OUTPUT CHECK. (LEVEL MAX) In the submenu screen shown below, press [EXECUTE] on the touch panel.

  • Page 101: Mx-Fwx1 (Internet Fax Expansion Kit)

    [14] MX-FWX1 MX-7000N Service Manual 1. Unpacking A. Check the packed items Names of bundles Quantity CD-ROM Product key sheet 2. Installation <Note before installation> * In order to enable the Internet Fax send function, the product key must be acquired. * In order to specify the address of the Internet Fax with the PCFAX driver, the PC-FAX driver must be updated by the Inter- net Fax expansion kit.
  • Page 102 LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
  • Page 103 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Page 104 COPYRIGHT © 2006 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher.

This manual is also suitable for:

Mx-6200nMx-7000n

Table of Contents