Playback Operation; Tv Auto On/Off Function - Marantz SR6300 User Manual

STATION NAME PRESET (On PRESET display mode)
The station name preset function allows the name of each preset
channel to be entered using alphanumeric characters. The Station
Name button is valid only in the tuner mode. Before station name
preset operation, store stations with the preset memory operation.
1.
Press the MEMORY button !3 on the front panel or MEMO button
¤6 on the remote for more than 3 seconds.
2.
The left most column of the station name indicator flashes,
indicating the character entry ready status.
[Operation (Using the SR6300)]
3.
When you press the TUNING/PRESET
turned, alphabetic and numeric characters will be displayed in the
following order:
A → B → C ...Z → 1 → 2 → 3..... 0 → – → + → / → (Blank) → A
UP →
← DOWN
4.
After selecting the first character to be entered, press the
MEMORY button !3 . The entry in this column is fixed and the next
column starts to flash. Fill the next column and press the
MEMORY button !3 for more than 1 second to confirm the entry.
[Operation (Using the remote control unit)]
First, press the TUNER button ⁄9 on the remote control unit.
(This operation is not necessary if the remote control unit has
already been operated in the TUNER mode.)
3.
Enter the character using the ten keypad ,. For example, to
enter "A":
1) Press the "1" button. "A" appears on the display column.
2) Every time the 1 button is pressed, the displayed character
changes in the order: A → B → C → 1 → A...
Pressing buttons other than the "1" button cause different
characters to be displayed in a similar way, so that other
alphanumeric characters can be entered. To enter a blank or
space, press the "9" button.
4.
When the desired character is displayed, press the MEMO button
¤6 to confirm the entry in this column and move to the next
column. After having filled all of the 8 columns, press the MEMO
button ¤6 , for more than 1 second to confirm the entry.

PLAYBACK OPERATION

NORMAL PLAYBACK
1.
2.
3.
buttons !4 is
or 4.
Note:
• In case of remote control operation, press one of the function
LISTENING TO A DIFFERENT AUDIO SOURCE WHILE
WATCHING A VIDEO SOURCE (Using the remote control unit)
1.
2.

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV IN jack to
control the power (ON/OFF) to the SR6300.
AUTO POWER ON
1.
2.
3.
4.
5.
AUTO POWER OFF
1.
2.
Note:
• AUTO POWER OFF is canceled if the FUNCTION
Caution:
• Some TV broadcasts may cause the TV AUTO FUNCTION to
• S-Video termianl does not support "TV AUTO ON/OFF"
21
Press the POWER button q / ‹4 .
Press the desired FUNCTION SELECTOR button t on the front
panel or press the desired FUNCTION button ⁄9 on the remote
unit to select an input source.
Turn the SURROUND MODE SELECTOR knob e on the front
panel or Surround mode buttons , in the AMP MODE on the
remote unit to select the desired surround mode.
Adjust the volume level using the VOLUME knob r on the front
panel or press the VOL. button ¤3 on the remote. If necessary,
adjust the tone, press the TREBLE , TREBLE ⁄4 and BASS ,
⁄4 on the remote unit.
BASS
buttons twice within 2 seconds to select the function.
Select one of the following video sources
TV, DVD, VCR1, DSS/VCR2 or AUX.
Next, select one of the following audio sources
FM, AM, CD, TAPE, or CDR/MD.
Be sure TV auto mode is enable. (Refer page 18 : PREFERENCE)
Connect your TV TUNER (etc) to the TV IN terminal.
Be sure to connect the video input.
Turn OFF the power to the TV TUNER and the SR6300 will be in
standby mode.
Turn ON the TV TUNER and tune in a receivable station.
When the station is received, the SR6300 turns ON and TV is
selected automatically.
In the above situation, turn the TV TUNER OFF or select a
channel that does not contain any broadcast.
The SR6300 switches to STANDBY after approximately 5
minutes.
SELECTOR button t is set to a source other than TV. The
function reactivates when TV is selected again.
turn on.
function.