Page 1
Service SR6010 / U1B/N1B/N1SG Manual AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Contents ABOUT THIS MANUAL ..............3 Audio Check PASS ..............114 What you can do with this manual ...........3 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK ....115 Using Adobe Reader (Windows version) ........4 LEVEL DIAGRAM ..............116 SAFETY PRECAUTIONS ...............6 BLOCK DIAGRAM ..............122 NOTE FOR SCHEMATIC DIAGRAM ..........7 POWER DIAGRAM ..............126 NOTE FOR PARTS LIST ..............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
Using Adobe Reader (Windows version) Add notes to this data (Sign) Magnify schematic / printed circuit board The Sign function lets you add notes to the data in diagrams - 1 (Ctrl+Space, mouse operation) this manual. Save the file once you have finished adding notes. Press Ctrl+Space on the keyboard and drag the [Example using Adobe Reader X] mouse to select the area you want to view.
Page 5
Magnify schematic / printed circuit board Magnify schematic / printed circuit board diagrams - 2 diagrams - 3 (Loupe Tool function) (Pan & Zoom function) The Pan & Zoom function lets you see which part of The Loupe Tool function lets you magnify a specific a magnified diagram is being shown in a separate part of a diagram in a separate window.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
CAUTION IN SERVICING Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. Press the power button to turn off the power. While holding down buttons "TUNER PRESET -" and "TUNER PRESET +" simultaneously, press the power button to turn on the power.
DISASSEMBLY • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "Precautions During Work" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 13
• The photographs with no shooting direction indicated were taken from the top of the unit. • Photos of SR6010 U are used in this manual. The viewpoint of each photograph (Shooting direction : X) [View from the top] Front side ↓Shooting direction: B↓...
1. FRONT PANEL ASSY Proceeding : TOP COVER → FRONT PANEL ASSY (1) Remove the screws. View from the bottom (2) Remove the screws. Cut the wire clamp, then remove the connector. Remove the FFC. CN102 CUT x4 CN104 2. RADIATOR ASSY Proceeding : TOP COVER →...
3. DIGITAL PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB (1) Remove the screws. Shooting direction: A (2) Cut the wire clamp, then remove the connector. Remove the FFC. CUTx5 CN903 CN704 FFC STYLE PIN CN321 (3) Remove the connector. BN24A BN26A BN25A BN21A BN23A...
4. VIDEO PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB (1) Cut the wire clamp, then remove the connector. PCB HOLDER を外します。 BN21B BN28B CUT x4 BN27B PCB HOLDER 5. INPUT HDAM PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB →...
6. SPK PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB → INPUT HDAM PCB SPK PCB → (1) Remove the screws. View from the bottom (2) Cut the wire clamp, then remove the connector. CN461 CN701 CN704...
SPECIAL MODE Special mode setting button No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power. No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds . No.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. then press the "STATUS" button to display the information in section 1.3 on the display. The version list is also displayed on GUI while the version is displayed on the display.
Page 20
y GUI SFLASH : G U I @ @ $ \ * * * * @ : Model code, $ : Brand code, \ : Region code (U=1, N=2, K=5, F=4) u Ethernet 1st Boot Loader, Hardware ID : N E T F B L * * * * * * * * - A A...
Page 21
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w , e , r , t , y , q . Condition States Display...
Page 22
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 14-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX-XX Version...
2. Selecting the Mode for Service-related Operations 2.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 2.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
2-1. DIAGNOSTIC MODE (Service Path Check Mode) 2-1.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The Video and Audio paths can be checked. The backup data is not rewritten. 2-1.2.
Page 26
Paths to be confirmed Display Settings What to confirm Analog A/D Input Source : CBL/SAT ・Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R) A 0 6 A D (MAIN ZONE) Input Mode : Analog (fixed) ・Analog input ⇒...
Page 27
Paths to be confirmed Display Settings What to confirm Front Amp>>Surround Back Input Source : CBL/SAT ・Analog input ⇒ Speaker output (Surround Back L/R) A 2 2 S B 2 Input Mode : Auto (b The input source can be switched to any source except CBL/SAT.) fig.12a * * * .
Page 28
2-1.6. Confirmation items for the video system See the block diagram fig.XXth. Paths to be confirmed Display Settings What to confirm Analog Video Input Source : CBL/SAT ・Component input ⇒ Component output V 0 1 V I D E O fig.14 Video Convert (IP Scaler) : OFF, All sources ・CVBS input ⇒...
Page 38
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.05a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 39
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.05b #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL COAX.1 MAIN ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 40
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.06 Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 41
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.07a #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL MAIN ZONE3 ZONE2 COAX.1 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 42
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.07b Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 43
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.08a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 44
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK DIRRST Except SR6010 #146 DIRCE #143 fig.08b DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL MAIN ZONE3 ZONE2 COAX.1 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK OPT.1 ADINR BCOSPDIF PCM9211PTR...
Page 45
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.09a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 46
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.09b #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL COAX.1 MAIN ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 47
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.10 Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 48
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.11a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 49
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.11b #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL COAX.1 MAIN ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 50
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.12a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 51
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.12b #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL COAX.1 MAIN ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 52
SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT fig.13a Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 53
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE fig.13b #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL COAX.1 MAIN ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK...
Page 54
SR6010 ANALOG VIDEO BLOCK fig.14 CBL/SAT CBL/SAT_V DVD_V CVBS IN Blu-Ray Blu-Ray_V V.AUX(FRONT) V.AUX_V CVBS OUT CVBS MONITOR COMPONENT OUT COMPONENT OUT Y CBL/SAT_Y COMPONENT OUT PB CBL/SAT CBL/SAT_PB COMPONENT OUT PR NJM2595MTE1 CBL/SAT_PR V_AUX_V DVD_Y CBL/SAT_V COMPONENT IN DVD_V...
Page 55
SR6010 ANALOG VIDEO BLOCK fig.15a CBL/SAT CBL/SAT_V DVD_V CVBS IN Blu-Ray Blu-Ray_V V.AUX(FRONT) V.AUX_V CVBS OUT CVBS MONITOR COMPONENT OUT COMPONENT OUT Y CBL/SAT_Y COMPONENT OUT PB CBL/SAT CBL/SAT_PB COMPONENT OUT PR NJM2595MTE1 CBL/SAT_PR V_AUX_V DVD_Y CBL/SAT_V COMPONENT IN DVD_V...
2-2. Protection History Display Mode 2-2.1. Actions This mode enables the unit to record and display the event when the THERMAL, CURRENT, ASO or DC protection is acti- vated. If protections have been activated multiple times, the latest protection operation is recorded. 2-2.2.
2-2.4. Clearing the Protection History There are two ways to clear the protection history. (a) Activate Protection History Display Mode. Press the "STATUS" button to display the protection history. Press and hold the "DIMMER" button for 3 seconds. P R O T E C T H I S T O R Y : D C Press and hold the "DIMMER"...
2-4. Operation Info Mode 2-4.1. Actions This mode enables the unit to display the accumulated operating time, power on count and each protection count. 2-4.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
2-5. TUNER STEP mode (E2 / E3 only) 2-5.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 2-5.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
3. PANEL / REMOTE LOCK Selection Mode 3.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 3.2. Starting up While holding down buttons "M-DAX" and "DIMMER" simultaneously, press the power button to turn on the power. Select the desired mode using the "TUNER PRESET CH+/-"...
4. Protection Pass Mode 4.1. Actions • This mode allows the power to be turned on without activating protections. • This mode functions in the same way as normal power-on, except that protections are not activated. 4.2. Operations While holding down buttons "DIMMER", "STATUS" and "SOUND MODE" simultaneously, press the power button to turn on the power.
6. CY920 Initialization Mode 6.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 6.2. Operations While the power is on, hold down buttons "TUNER PRESET CH-" and "DIMMER" for at least 3 seconds. Initializing Display I n i t i a l W a i t...
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. Order with your dealer for the jigs your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for DIGITAL PCB ---Items to Be Prepared--- 8U-110084S EXTENSION UNIT KIT 1Sets...
Page 74
BN21B BN28B CUT x4 BN27B PCB HOLDER From AMP PCB BN24C BN26C STYLE PIN CN706 BN64C BN23C (3) Remove the DIGITAL PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. Connect the earth of the PCB to the chassis using an earth wire, etc.
Page 75
(4) Connect the expansion cables. PCB FRONT CNT PCB DIGITAL PCB SIDE CNT PCB FRONT CNT PCB VIDEO PCB SIDE CNT PCB FRONT CNT PCB INPUT PCB SIDE CNT Board-to-Board Connections Ref. No. Ref. No. 15pin CN27A SIDE CNT BN27A DIGITAL 27pin CN23A...
(1) Change the resistor for setting the region. DIGITAL PCB Model Name Model Area R1589 R1590 North America (U) OPEN SR6010 Europe (N) OPEN See the PCB below. (2) Be sure to rewrite with the latest software for your service region. D4332 D4312 D3804...
FIRMWARE UPDATE PROCEDURE 1. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 1.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 78
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure. USB memory root Model Name Model Area Product ID North America (U) 100100420100 SR6010 Europe (N) 100100420200 + firmwares + 000100XXXXXX + APLD.bin + DSP1.bin + DSP2.bin + DSP3.bin...
Page 79
1.8. The firmware update finishes. When the update is completed, the following message appears on the display, then the unit returns to the normal status. Display U p d a t i n g C o m p l e t e ---Cautions on Firmware Update--- •...
Page 80
1.11. About the error codes See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Remedies Code C o n n e c t Disconnect and reconnect the USB Unable to detect USB.
Page 81
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the M a i n request several times. Wait until the Failed in Block Erase while rewrit- Display stops. If the Display stops at the U p d a t i n g ing Main.
Page 82
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the M a i n request several times. Wait until the Time Out in USB Check. Display stops. If the Display stops at the C o n e c t Error display, press and hold the "Power f a i l e d operation"...
Page 83
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the A P L D NACK received in response or request several times. Wait until the no response from Sub for the "L" Display stops. If the Display stops at the U p d a t i n g command.
Page 84
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the G U I Abnormal data in Update Packet request several times. Wait until the received from CY920 (Data Length Display stops. If the Display stops at the U p d a t i n g / Data No).
Page 85
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the E I M G request several times. Wait until the Failed to transit to Application Display stops. If the Display stops at the U p d a t i n g Mode.
2. Updating via DPMS Download the latest firmware from our website and update the firmware. 2.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 87
2.3. About the error codes See the following table for details on the error code display, details of the error code, remedies when updating the firm- ware via DPMS. (DPMS : D&M Product Management Server) Error DPMS Update Error Display Details of Error code Remedies Code...
Page 88
Error DPMS Update Error Display Details of Error code Remedies Code M a i n No Update Packet received from Turn off and on the power. Updating U p d a t i n g CY920 (Time Out). starts automatically. f a i l e d M a i n Abnormal data in Update Packet...
Page 89
Error DPMS Update Error Display Details of Error code Remedies Code M a i n Carry out the update in an environment DPMS login incorrect notification. L o g i n that has little network load. f a i l e d M a i n Carry out the update in an environment DPMS congestion notification.
Page 90
Error DPMS Update Error Display Details of Error code Remedies Code Turn off and on the power. Updating A P L D Error(NG) notification received starts automatically. while requesting Firmware Down- D o w n l o a d Carry out the update in an environment load.
Page 91
Error DPMS Update Error Display Details of Error code Remedies Code G U I Abnormal data in Update Packet Turn off and on the power. Updating received from CY920 (PacketNo- U p d a t i n g starts automatically. Error).
Page 92
Error DPMS Update Error Display Details of Error code Remedies Code Turn off and on the power. Updating E I M G Error in Firmware Update (Time starts automatically. U p d a t i n g Out). Carry out the update in an environment that has little network load.
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity.。 (3) Settings of This Unit •...
Contents Connections Playback Settings Tips Appendix SURROUND MODES AND PARAMETERS Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.”. (v p. 222) Channel output Front Surround...
Page 95
Contents Connections Playback Settings Tips Appendix Sound modes and surround parameters Surround Parameter Loudness Dynamic Low Frequency Sound mode Subwoofer Level Dialog Control Dialog Level Adjust Cinema EQ Management Compression Speaker Select Adjust Direct/Pure Direct (2-channel) z5 Direct/Pure Direct (Multi-channel) z5 DSD Direct (2-channel) DSD Direct (Multi-channel) z5 Stereo...
Page 96
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Dolby Dolby Dolby Sound mode NOTE Analog / (Super DTS- DTS ES...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator on the front Does the power indicator on the front panel flash in green when the power is panel flash in red when the power is turned on? turned on? See "1.2.Fuse is blown."...
2. Analog video COMPONENT/HDMI OUT NG Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI TO "3 HDMI/DVI" To A DIGITAL test point D4332 D4312 D3804 T296 T279 T281 T274 T275 T269 T214 T220 T126 JK201...
Page 99
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the following points? DIGITAL PCB Check the connection between Input CVBS:Check B : R3527 Input COPONENT:Check C the PCBs. COMPONENT-Y : R3530 COMPONENT-Cb : R3528 COMPONENT-Cr...
Page 100
Input CVBS Check the set value of each IC. Are the voltage values as follows? DIGITAL PCB The DIGITAL PCB is faulty. BN21A - 3pin : Hi(3.3V) BN21A - 4pin : Hi(3.3V) BN21A - 5pin : Lo(0V) Use the jigs to extend the DIGITAL PCB.
Page 101
Input COMPONENT Check the set value of each IC. Are the voltage values as follows? The DIGITAL PCB is faulty. DIGITAL PCB BN21A - 2pin : Lo(0V) BN21A - 1pin : Hi(3.3V) Use the jigs to extend the DIGITAL PCB. Is the power supply voltage Check the connection between being output correctly?
3. HDMI/DVI 3.1. No picture or sound is output (HDMI to HDMI) No picture or sound is output. Check the connection of the HDMI/DVI cable. (1) Is the HDMI/DVI cable correctly inserted? Check the connection of the HDMI/DVI cable. (2) Is an HDMI/DVI selector, repeater or image quality improvement Remove all of these and connect only the HDMI/DVI device being used? cable.
Page 103
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors (12) Does the TV support HDCP? cannot be used. If the TV does not support 1080P/4K, a picture cannot (13) Does the TV support 1080P/4K? be output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output See "Audio Check PATH" (page 114). CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK3 INPUT...
Page 105
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short cir- cuited? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistor of the power transis- tor open? Replace the emitter resistor. 0.47 Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 106
4.3. Analog audio No audio output. Is a voltage of ± 7V supplied to SIDE CNT Repair the ± 7V power supply. PCB CN64C 4-7 pin? Is there an audio signal in AMP PCB CN461? Repair the power amplifier. Is electron volume serial data being sent to Check the CPU.
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Is the LAN cable correctly inserted? Insert the LAN cable correctly and then turn on the power again. Check the connection environment Set the IP address, etc. correctly. When the static IP address is used, check that no other devices Are the network settings of this unit correct? have the same IP address and that the subnet mask settings are...
Page 108
Can the output voltage (3.3 V) to Q1107 The circuit of E_POWER1 between IC151 Is E_POWER1 (IC151 uCOM 132 pin) "Hi" ? (FET-SW) be confirmed? and Q1107 are faulty. The circuit around Q1107 (FET-SW) is faulty. Can the output voltage (1.2 V) to IC115 The circuit of E_POWER4 between IC115 Is E_POWER4 (IC151 uCOM 135 pin) "Hi"...
Page 109
5.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Is the Bluetooth function enabled on the Bluetooth device? Enable the Bluetooth function and try connecting again. Checking the unit Is the Wi-Fi/BT antenna cable inserted correctly into CY920? Connect the Wi-Fi/BT antenna cable correctly.
Page 110
5.3. Cannot recognize the connected USB device Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16- and FAT32-formatted Is the USB device supported by this unit? mass storage class, MTP-compatible devices and iPod devices (except for some models).
6. SMPS DC 5V is not output. Replace the IC901 (TOP268EG) and Is IC901 (TOP268EG) damaged? D9001 - D9004. Is IC901 (TOP268EG) and D9001 - D9004 Is the fuse (F9001) functioning properly? Replace the damaged part. damaged? Are there any short circuits caused by the Repair the short circuited area on the soldering on the PCB? PCB.
Page 113
Operation waveform for each part After primary side rectification Primary drain (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C9002 0.01uF 250V OPTION OPTION D9001 1N4007 After secondary rectifications D9002 1N4007 HEATSINK CMY3A238 D9003 1N4007 (16.5*16*30) D9004 1N4007 C9013 D9005 1N4007 50V/1000pF(3216)
LEVEL DIAGRAM SR6010 LEVEL DIAGRAM FRONT ch LINE IN MUTE PRE OUT GAIN PCN1690 ADJ. + + + AK5358 - - R2A15220FP ANALOG H/P OUT SPEAKER + R2A15218FP AK5358 +30dB 4.22Vrms:A/D FULL SCALE SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.23Vrms/8Ω...
Page 117
SR6010 LEVEL DIAGRAM CENTER ch MUTE PRE OUT GAIN PCM1690 ADJ. + + - - R2A15220FP SPEAKER + R2A15218FP +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.23Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS)
Page 118
SR6010 LEVEL DIAGRAM SUBWOOFER ch PCN1690 + + - - R2A15220FP R2A15218FP MUTE PRE OUT GAIN ADJ. +30dB MAX. SIGNAL LEVEL R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms Differential Out PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS) 2.83Vrms=0dBFS +20dB +20dB -10dBFS +10dB +10dB PREOUT -20dBFS...
Page 119
SR6010 LEVEL DIAGRAM SURROUND ch PCM1690 + + - - R2A15220FP SPEAKER + R2A15218FP MUTE PRE OUT GAIN ADJ. +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.23Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS)
Page 120
SR6010 LEVEL DIAGRAM SURR.BACK / Front Wide / Height1 / Height2 ch PRE OUT GAIN PCM1690 ADJ. + + - - R2A15220FP + SPEAKER R2A15218FP GAIN ADJ. +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.23Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL...
Page 121
SR6010 LEVEL DIAGRAM ZONE2 To MAIN LINE IN ZONE PCM5100 MUTE TONE PRE OUT GAIN PCM5100 MONO ADJ. R2A15220FP MONO BD3841FS MONO SPEAKER + MONO R2A15218FP TONE Z2 MONO from D/A F-ch GAIN from D/A SB-ch ADJ. from D/A FH/FW-ch...
BLOCK DIAGRAM SR6010 ANALOG AUDIO BLOCK Z2L_VOL_OUT Z2R_VOL_OUT HDAM R2A15220 70,71 CBL/SAT FL_VOL_OUT PREOUT_FL 72.73 74,75 19,20 Z2 IN1 FR_VOL_OUT PREOUT_FR 76,77 TONE Blu-Ray Z2 IN2(HPF/MONO) 78,79 C_VOL_OUT PREOUT_C Media 82,83 64,65 SW1_VOL_OUT PREOUT_SW1 66,67 22,23 PHONO 62,63 TONE SW2_VOL_OUT PREOUT_SW2 V.AUX...
Page 123
SR6010 ANALOG VIDEO BLOCK CBL/SAT CBL/SAT_V DVD_V CVBS IN Blu-Ray Blu-Ray_V V.AUX(FRONT) V.AUX_V CVBS OUT CVBS MONITOR COMPONENT OUT COMPONENT OUT Y CBL/SAT_Y COMPONENT OUT PB CBL/SAT CBL/SAT_PB COMPONENT OUT PR CBL/SAT_PR NJM2595MTE1 V_AUX_V DVD_Y CBL/SAT_V COMPONENT IN DVD_V DVD_PB...
Page 124
SR6010/ S R7010/ A V7702MK2 DIGITAL AUDIO BLOCK Except SR6010 DIRRST #146 DIRCE #143 DIRDIN #141 DIRDOUT #144 Z3DIRSPDIF DIRCLK #145 Z2DIRSPDIF 24.576MHz COAX.0 DATAAD ADINL MAIN COAX.1 ZONE3 ZONE2 DIRSLRCK OPT.0 DIGTAL IN DIRSBCK ADINR OPT.1 BCOSPDIF DIRSMCK PCM9211PTR...
TO B2 TO 1D TO 0D TO A4 TO B7 TO B5 TO B6 (PAGE 1) (PAGE 5) TO DIGITAL CNT TO LEVEL CHG. A3,4 4.7K R1577 R1578 OPEN R1585 4.7K R1579 OPEN R1580 OPEN OPEN R1581 DSP_ICS DSP_ICS DSP_MOSI DSP_MOSI DSP_MISO DSP_MISO...
TO B4 TO 4E TO 5E TO 6E TO 7E TO 8E TO A7 TO B1 (PAGE 16_C6) DIGITAL CNT (PAGE 8-1_D1) (PAGE 13_A4) (PAGE 17_D6) (PAGE 14_A3) VIDEO PLD PAGE 1 TO DSP1 HDMI SW2 HDMI TX HDMI SW1 TO A9 R1702 OPEN...
Q1916 Q1922 2SC3052 2SC3052 ISA1530AC1 ISA1530AC1 2SC3052 2SC3052 2SC3052 2SC3052 Q1912 ISA1530AC1 SR6010/7010 ONLY SR7010 ONLY SR6010/7010 ONLY PROTECT TO D1 TO AUDIO PLD (PAGE 7_D1) TO MAIN CPU TO 9E (PAGE 3_D5) SCHEMATIC DIAGRAMS (05/38) GND LINE POWER+ LINE...
TO F8 TO 6G TO F9 TO 7G TO 8G TO 9G TO 0H TO E3 TO E7 (PAGE 7_A5) (PAGE 7_A5) (PAGE 8-2_D5) (PAGE 8-2_D3) (PAGE 8-4_D2) (PAGE 8-3_D2) (PAGE 8-1_D2) (PAGE 3_D1) (PAGE 4_C4) TO DSP2 PART FROM A.PLD PART FROM MAIN CPU PART FROM AUDIO PLD TO DSP2 PART...
TO G6 TO G7 TO G0 TO H0 (PAGE 7_A4) (PAGE 8-2_D2) (PAGE 8-1_D3) (PAGE 8-1_D4) FROM DSP1 PART TO A.PLD PART FROM DSP1 PART FROM DSP1 PART 5 6 7 8 5 6 7 8 1 2 3 4 1 2 3 4 IC262 C2645 1000P...
TO F7 TO 1H TO G1 TO G9 (PAGE 7_A4) (PAGE 8-1_D2) (PAGE 7_A5) (PAGE 8-4_D5) ADUDIO PLD PART FROM DSP1 PART FROM AUDIO PLD TO DSP4 PART IC272 C2745 1000P A3V56S40GTP-60 256M BIT SDRAM C2737 C2746 VDD_INT DAI_P09 R2745 DSP3_FLAG0 FLAG0 DAI_P05...
TO H1 TO G2 TO G8 (PAGE 7_A4) (PAGE 8-3_D4) (PAGE 8-1_D2) FROM DSP3 PART ADUDIO PLD PART FROM DSP1 PART IC282 C2855 1000P A3V56S40GTP-60 256M BIT SDRAM C2847 C2856 VDD_INT DAI_P09 R2845 DSP4_FLAG0 FLAG0 DAI_P05 DQ15 R2846 4.7K C2857 FLAG1 DAI_P06 DSP4D0...
TO G3 TO D4 TO F2 (PAGE 7_A3) (PAGE 3_C6) (PAGE 6_C5) TO AUDIO PLD TO MAIN CPU TO DIR A+5V ADINL ADINR DAGND TO A2 C3055 C3056 C3057 1000P C3058 1000P C3061 1000P C3062 1000P C3063 1000P C3064 1000P C3066 1000P C3067...
FRT CNT CONNECT B CN21A CN25A DIGITAL CNT PART TO BN25A TO BN21A PAGE 1_B3 CN24A SR6010 ONLY TO BN24A DIGITAL CNT PART CN26A DIGITAL CNT PART TO 5J DIGITAL CNT PART PAGE 1_D3 TO BN26A PAGE 1_D5 PAGE 1_B5 TO 9K FROM/TO DIGITAL CON.
R9821 TUNER PART C9827 R9825 OPEN OPEN C9821 C9825 OPEN L9821 OPEN OPEN R9823 R9827 OPEN C9809 OPEN C9810 OPEN CHASSIS C9828 R9826 OPEN OPEN C9826 C9811 L9822 OPEN OPEN 0.1uF R9824 CHASSIS R9828 OPEN C9822 OPEN TU901 TUNER_L L-OUT TUNER_R R9822 R-OUT...
EXPLODED VIEW Please see the last chapter for the part list. M24 X2 M23 X2 S16 X2 C23-1 C23-2 M22 X2 S10 x2 S5 x21 S3 X2 S3 X2 WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F564MJCDFC (DIGITAL : IC151) Terminal Functions Pin Name Symbol Function Pu/Pd STBY STOP CEC STBY AVSS0 AVSS0 P05/IRQ13 POWER KEY...
Page 176
Pin Name Symbol Function Pu/Pd STBY STOP CEC STBY MD/FINED Unused M3VPu XCIN XCIN NC(Pull down) XCOUT XCOUT NC(open) RES# RESET Reset input XTAL/P37 XTAL Oscillator connection(12MHz) EXTAL/P36 EXTAL Oscillator connection(12MHz) POWER pin UPSEL/P35(IN)/NMI DSP FLAG3 DSP control pin P34/SCK6/SCK0/IRQ4 BDOWN Power failure detection pin P33/TIOCD0/RXD6/RXD0/ RC IN Remote control signal input pin...
Page 177
Pin Name Symbol Function Pu/Pd STBY STOP CEC STBY P77/TXD11 DSP RST DSP reset output pin (Reset : L) P76/RXD11 DSP BUSY DSP control pin DIGITAL AUDIO POWER SUPPLY (DA3.3V) control pin. PC2/RXD5 DA_POWER (ON:H) P75/SCK11 CEC POWER2 CEC STANDBY SUPPLY control pin(CEC STANDBY) DSP ROM rewrite path switching DSP ROM WRITE (DSP rewritten during the "H")
Page 178
Pin Name Symbol Function Pu/Pd STBY STOP CEC STBY PD6/IRQ6/AN106 DIR CLK DIR control pin(PCM9211) DIR RST DIR control pin(PCM9211) PD5/IRQ5/AN113 788_2_HAINT HDMI MN864788(RX) Audio INT input pin PD4/IRQ4/AN112 Unused DE_RST HDMI ADV7850 RESET control pin PD3/IRQ3/AN111 788_1_HINT HDMI MN864788(TX) HDMI INT input pin 788_1_RST HDMI MN864788(TX) RESET control pin ※...
Page 186
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION PCM5100 (DIGITAL : IC321/IC322) TERMINAL FUNCTIONS, PCM510x PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 187
PCM1690 (FRONT CNT : IC301, IC311) Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 —...
Page 188
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 RSV2 — — — Reserved, tied to analog ground PCM1690 AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 189
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control R2A15220FP (INPUT : IC471) BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB -∞...
Page 190
Notice ; This is not a final specification. Some parametric limits are subject to change. R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION Pin Assignment PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT...
Page 191
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15218FP (INPUT : IC491) AVCC MUTE AVCC N.C. AVEE AVEE N.C. TREL 0/-6/-12/-18dB ADCL BASSL2 BASSL1 ADCR N.C. AGND Bass/ Treble 0~-95dB, -14~+14dB -∞ +42~0dB MAIN N.C.
Page 192
R2A15218FP R2A15218FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control PIN DESCRIPTION Pin Function PIN No. Function Name 23,21, FROUT,FLOUT, 17,15, COUT,SWOUT, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel 11,9, SROUT, SLOUT, SBROUT,SBLOUT 24,20, FRC,FLC, 18,14, CC,SWC, Connects capacitor for reducing click noise of 12,8, SRC,SLC, L/R/C/SW/SL/SR/SBL/SBR channel volume...
Page 193
1pin 0.38 0.1 Reel (Unit : mm) Order quantity needs to b BD3841FS (INPUT : IC484) SSOP-A32 <Tape and Reel information> 13.6 0.2 Tape Embossed carrier tape (MAX 13.95 include BURR) Quantity 2000pcs Direction The direction is the 1pin of product is at t of feed reel on the left hand and you pull out the 0.15 0.1...
Page 194
The NJU72751 is a 4-input / 4-output dual analog switch. NJU72751 Functions are controlled via two-wired serial bus. A-channel switches and B-channel switches are controlled independently. The NJU72751 is well-suited for multi-channel audio systems such as AV amplifiers, DVD receivers and others. NJU72751V (INPUT : IC871) NJU72751V PIN CONFIGURATION...
Page 196
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 197
FRONT REF No. Part No. Part Name Remarks Q'ty New Ver ! F6001 943652500550D FUSE(372 Series/200mA/TR5) CBA2D0200A3EYT FL601 172010008005S CFLGP1261AI JK601 943643101590S JACK, USB STRAIGHT(BLACK 1.5A) CJJ9X010Z JK602 943643102220S JACK, MONO, 3.5mm, SILVER CJJ1D004Z JK603 90M-YT004500R JACK, PHONES(6.35mm,SILVER) CJJ2E026Z JK604 943643102980S JACK, 3P(B/B/B)with S/W, SILVER, VERTICAL CJJ4S051Z...
Page 198
SPK PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 199
REF No. Part No. Part Name Remarks Q'ty New Ver GND92 PLATE , EARTH(TRONIC ELECTRONICS) CJT1A026 JK921-931 943643102490M 2P, SCREW SPK(R/B,GOLD,94V-0,Transparence) CJJ5N025Z JW925A WIRE ASS'Y (1P, 100mm, BLK, UL1015#20, CKM-T) CWE7102100TT L9201-9207 943115010260S COIL , SPEAKER(0.5uH) CLEY0R5KAK RY921-928 682010023006S RELAY,HL3-2A-12S,DC12V,2C1P CSL3A021ZU RY930 943682000810S...
Page 200
HDAM HDAM PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 201
HDAM REF No. Part No. Part Name Remarks Q'ty New Ver R8221-8224 RES, CHIP(1608/5%/330ohm) CRJ10DJ331T R8225,8226 RES, CHIP(1608/5%/1Mohm) CRJ10DJ105T R8227-8230 RES, CHIP(1608/5%/22ohm) CRJ10DJ220T R8231-8234 RES, CHIP(1608/5%/5.6Kohm) CRJ10DJ562T R8235-8238 RES, CHIP(1608/5%/22ohm) CRJ10DJ220T R8239,8240 RES, CHIP(1608/5%/220ohm) CRJ10DJ221T R8241,8242 RES, CHIP(1608/5%/100ohm) CRJ10DJ101T R8243,8244 RES, CHIP(1608/5%/0ohm) CRJ10DJ0R0T R8246...
Page 202
SMPS SMPS PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 203
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 204
FRONT CNT FRONT CNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 205
FRONT CNT REF No. Part No. Part Name Remarks Q'ty New Ver CN24C,25 PIN HEADER (23P,1.25mm,STRAIGHT,B-TO-B) CJP23GI281Z CN26A PIN HEADER (09P,1.25mm,STRAIGHT,B-TO-B) CJP09GI281Z CN26C PIN HEADER (15P,1.25mm,STRAIGHT,B-TO-B) CJP15GI281Z JW9604 WIRE ASS'Y(1P, 80MM,BLK,#22) CWE5202080A L3001 FERRITE CHIP BEAD(2012/220R, CB05YTYH221) CLZ9R018V...
Page 206
SIDE CNT SIDE CNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 207
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 208
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver R4794-4799 RES, CHIP(1608/5%/0ohm) CRJ10DJ0R0T R4801,4802 RES, CHIP(1608/5%/470Kohm) CRJ10DJ474T R4803,4804 RES, CHIP(1608/5%/150Kohm) CRJ10DJ154T R4805,4806 RES, CHIP(1608/5%/270Kohm) CRJ10DJ274T R4807,4808 RES, CHIP(1608/5%/0ohm) CRJ10DJ0R0T R4811,4812 RES, CHIP(1608/5%/100ohm) CRJ10DJ101T R4813,4814 RES, CHIP(1608/5%/100Kohm) CRJ10DJ104T R4815-4818 RES, CHIP(1608/5%/68Kohm) CRJ10DJ683T R4819,4820...
Page 209
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver R8913-8916 RES, CHIP(1608/5%/470ohm) CRJ10DJ471T R8917-8920 RES, CHIP(1608/5%/100Kohm) CRJ10DJ104T R8921,8922 RES, CHIP(1608/5%/220ohm) CRJ10DJ221T R8923 RES, CHIP(1608/5%/10Kohm) CRJ10DJ103T R8925-8928 RES, CHIP(1608/5%/10Kohm) CRJ10DJ103T R8929 RES, CHIP(1608/5%/470Kohm) CRJ10DJ474T R8930 RES, CHIP(1608/5%/1Kohm) CRJ10DJ102T CAPACIITORS GROUP C1001 CAP, CHIP(1608, 50V/0.1uF, X7R)_SAMSUNG CCUS1H104KCS...
Page 210
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver C8991,8992 CAP, CHIP(1608, 50V/0.1uF, X7R)_SAMSUNG CCUS1H104KCS OTHER PARTS GROUP BK103 EARTH , HDMI CMC2A436 BK469 EARTH , INPUT CMC1A440 BN23C PIN SOCKET (21P,1.25mm,ANGLE, B-TO-B) CJP21HJ282Z BN24C PIN SOCKET (23P,1.25mm,ANGLE, B-TO-B) CJP23HJ282Z BN26C PIN SOCKET (15P,1.25mm,ANGLE,B-TO-B)
Page 212
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R1124 RES, CHIP(1608/1%/348Kohm) CRJ10DF3483T R1125 RES, CHIP(1608/1%/76.8Kohm) CRJ10DF7682T R1126 RES, CHIP(1608/5%/0ohm) CRJ10DJ0R0T R1131 RES, CHIP(1608/5%/10ohm) CRJ10DJ100T R1132 RES, CHIP(1608/5%/4.7Kohm) CRJ10DJ472T R1133 RES, CHIP(1608/5%/100Kohm) CRJ10DJ104T R1134 RES, CHIP(1608/1%/348Kohm) CRJ10DF3483T R1135 RES, CHIP(1608/1%/76.8Kohm) CRJ10DF7682T R1136...
Page 213
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R1619-1624 RES, CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R1701 RES, CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R1905 RES, CHIP(1005/5%/100ohm) CRJ06IJ101T R1906 RES, CHIP(1005/5%/22Kohm) CRJ06IJ223T R1907 RES, CHIP(1005/5%/0ohm) CRJ06IJ0R0T R1908 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R1910 RES, CHIP(1005/5%/100ohm) CRJ06IJ101T R1911 RES, CHIP(1005/5%/22Kohm) CRJ06IJ223T R1912...
Page 214
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R2625,2626 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R2627 RES, CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R2629 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R2630 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R2631 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R2633-2640 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R2641 RES, CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R2642 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R2643...
Page 215
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R3539-3544 RES, CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R3547 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R3548 RES, CHIP(1608/1%/470ohm) CRJ10DF4700T R3801 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R3804 RES, CHIP(1005/5%/47ohm) CRJ06IJ470T R3805 RES, CHIP(1608/5%/1Mohm) CRJ10DJ105T R3806 RES, CHIP(1608/5%/1Kohm) CRJ10DJ102T R3807 RES, CHIP(1005/5%/10Kohm) CRJ06IJ103T R3808,3809...
Page 216
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R4234-4240 RES, CHIP(1005/5%/47ohm) CRJ06IJ470T R4243,4244 RES, CHIP(1005/5%/47ohm) CRJ06IJ470T R4245 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R4246 RES, CHIP(1005/5%/47ohm) CRJ06IJ470T R4249 RES, CHIP(1005/5%/100ohm) CRJ06IJ101T R4301 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R4303 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R4308 RES, CHIP(1005/5%/33ohm) CRJ06IJ330T R4310,4311...
Page 217
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C1129 CAP, CHIP(2012, 50V/0.1uF, X7R)_SAMSUNG CCUC1H104KCS C1131 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C1132 CAP, CHIP(2012, 6.3V/10uF, X5R)_SAMSUNG CCUC0J106KCS C1133 CAP, CHIP(1608, 10V/1uF, X7R, X7S)_SAMSUNG CCUS1A105KCS C1134 CAP, CHIP(1608, 50V/3.3pF, C0G)_SAMSUNG CCUS1H3R3JAS C1135 CAP, CHIP(2012, 6.3V/22uF, X5R)_SAMSUNG...
Page 218
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C2225 CAP, CHIP(1005, 50V/100pF, C0G)_SAMSUNG CCUI1H101JAS C2227 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C2228 943134503260S CAP , ELECT (100uF/6.3V, PVO, ELNA) CCEC0JPVO101TS C2443 CAP, CHIP(1005, 50V/1000pF, X7R)_SAMSUNG CCUI1H102KCS C2502,2503 CAP, CHIP(1608, 50V/18pF, C0G)_SAMSUNG CCUS1H180JAS C2505-2507 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG...
Page 219
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C3526 CAP, CHIP(1608, 6.3V/4.7uF, X5R)_SAMSUNG CCUS0J475KCS C3528 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C3529 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C3531 CAP, CHIP(1608, 6.3V/4.7uF, X5R)_SAMSUNG CCUS0J475KCS C3535 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C3536 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG...
Page 220
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C3686 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C3687 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C3688 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C3689 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C3690 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C3691 CAP, CHIP(1608, 6.3V/4.7uF, X5R)_SAMSUNG...
Page 221
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C4087 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C4088 CAP, CHIP(1608, 6.3V/4.7uF, X5R)_SAMSUNG CCUS0J475KCS C4090,4091 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C4092 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG CCUI1E103KCS C4093 CAP, CHIP(1005, 16V/0.1uF, X7R)_SAMSUNG CCUI1C104KCS C4094 CAP, CHIP(1005, 25V/0.01uF, X7R)_SAMSUNG...
Page 222
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver BN21A PIN SOCKET (19P,1.25mm,ANGLE, B-TO-B) CJP19HJ282Z BN23A,24 PIN SOCKET (27P,1.25mm,ANGLE,B-TO-B) CJP27HJ282Z BN25A PIN SOCKET (23P,1.25mm,ANGLE, B-TO-B) CJP23HJ282Z BN26A PIN SOCKET (09P,1.25mm,ANGLE,B-TO-B) CJP09HJ282Z BN27A PIN SOCKET (15P,1.25mm,ANGLE,B-TO-B) CJP15HJ282Z CN152 WAFER, FFC, SMD(11P-1mm, STRAIGHT) CJP11GA193ZY CN221 WAFER, FFC, SMD(07P-1mm, STRAIGHT)
Page 223
7CH AMP 7CH AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 224
7CH AMP REF No. Part No. Part Name Remarks Q'ty New Ver R7106 RES, CHIP(1608/5%/470ohm) CRJ10DJ471T R7107 RES, CHIP(1608/5%/0ohm) CRJ10DJ0R0T R7108 RES, M-OXIDE FILM(1W/1Kohm) CRG1SANJ102RT R7110 RES, CARBON(1/5W,110ohm,J) CRD20TJ111T R7111 RES, M-OXIDE FILM(1W/3.3Kohm) CRG1SANJ332RT R7112 RES, CARBON(1/5W,33Kohm,J) CRD20TJ333T R7114 RES , METAL(1/2W, 27k OHM) CRG12SANJ273T R7116,7117 RES, CHIP(1608/5%/1.2Kohm)
Page 225
7CH AMP REF No. Part No. Part Name Remarks Q'ty New Ver R7444 RES, CHIP(3216/5%/22Kohm) CRJ14CJ223T R7445 RES, CARBON(1/5W,22Kohm,J) CRD20TJ223T R7501 RES, CARBON(1/5W,1.2Kohm,J) CRD20TJ122T R7502 RES, CARBON(1/5W,470Kohm,J) CRD20TJ474T R7503 RES, CARBON(1/5W,33Kohm,J) CRD20TJ333T R7504 WIRE, COPPER(D0.6) C3A206 0.02 R7505 RES, M-OXIDE FILM(1W/1Kohm) CRG1SANJ102RT R7506 RES, CHIP(1608/5%/470ohm)
Page 226
7CH AMP REF No. Part No. Part Name Remarks Q'ty New Ver C7225 CAP, ELECT(25V/220uF) CCEA1EH221T C7238 CAP, CHIP(1608, 50V/0.1uF, X7R)_SAMSUNG CCUS1H104KCS C7301 00D2544574919 CAP, ELECT(50V/47uF),ELNA/RA3 CCEA1HRA3470T C7302 CAP, PE-FILM(100V/470pF/J) CCME2A471JR11T C7304 CAP, PE-FILM(100V/220pF/J) CCME2A221JR11T C7306 00D2544569937 CAP, ELECT(25V/220uF,ELNA/RA3) CCEA1ERA38P221T C7307 CAP, MYLAR(50V/2200pF/J) HCQI1H222JZT...
Page 227
WIRE ASS'Y LOCKING (5P,2.5MM,220MM,UL1569#20,105) CWB7E0052203D TO SPK-BN932 WIRE ASS'Y LOCKING (9P,2.0MM,220MM,UL1007#26) CWB1B009220HC TO INPUT-BN461 WIRE ASS'Y Locking (YH) (13P,2MM,150MM,#26) CWB1B013150HC 421410006004M BADGE , MARANTZ CGB1A206 943402105820S PANEL , AL FRONT CKM1A249GC23 943402105830S PANEL , AL FRONT CKM1A249FC23 943402105840S PANEL , AL FRONT...
Page 228
EXPLODED REF No. Part No. Part Name Remarks Q'ty New Ver 943474001390S GEAR , DEMPER AV8003 CDG1A027Z COVER , DAMPER CMH1A368 COVER , DAMPER CMH1A368RO 943411103340M BUTTON , 9KEY CBT1A1198B37 943411103350M BUTTON , 9KEY CBT1A1198RMD10 FOOT , FRONT CKL2A042H46 00M32CW107010 CUSHION , FOOT CHG1A360 RUBBER CHG1A113...
Page 229
PACKING PACKING ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...