Table of Contents
Advertisement
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
WARNING:
Do not plug in the power
cord until the treadmill is completely assembled.
1. With the help of a second person, carefully raise the
Uprights (69) so that the treadmill is in the position
shown.
See the inset drawing. Insert one of the Extension Legs
(102) into the treadmill as shown. Make sure that the
Extension Leg is turned so the Base Pad (99) is on the
bottom. Note: It may be helpful to tip the Uprights (69)
forward as you insert the Extension Leg. Insert the other
Extension Leg (not shown) in the same way.
2. Press the Lock Knob Sleeve (70) into the left Upright (69).
Make sure that the Lock Pin Collar (72) and the Spring
(71) are on the Lock Pin (74). Insert the Lock Pin into
Lock Knob Sleeve (70) and the left Upright (69). Press the
Lock Knob Spacer (117) onto left Upright. Tighten the
Lock Knob (68) onto the Lock Pin.
3. With the help of a second person, tip the Uprights (69)
down as shown. Make sure that the Extension Legs
(102) remain in the Uprights.
Attach each Extension Leg (102) with two 3/4" Screws
(111) as shown.
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position.
Note: A replacement Base Pad (99) may be included. Use
the Base Pad to replace any Base Pad that becomes worn.
and wire cutters
.
1
69
2
69
68
70
71
117
72
3
99
69
69
102
111
99
102
6
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 8.) If an exten-
sion cord is needed, use only a 3-conductor, 1 mm
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
69
near the power cord. The switch must be in the on
position.
PROBLEM: The power turns off during use
99
102
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
74
POWER CORD. Carefully tip the treadmill down as
shown in drawing a. Remove the Screws (39, 90) from
the hood. Raise the Uprights (69) and carefully re-
move the hood.
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.). If necessary, loosen
the 3/4" Screw (111) and move the Reed Switch
111
slightly. Retighten the Screw. Re-attach the hood, and
run the treadmill for a few minutes to check for a cor-
rect speed reading.
2
(14-gauge) cord that is no longer than 1.5 m
c
Tripped
Reset
Tripped
Reset
d
On
Position
a
39
90
69
3 mm
8
111
7
10
Top
View
23
Advertisement
Table of Contents
