Power Spot 575™ INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Spot 575™, has been designed to perform reliably for years when the guidelines in this booklet are followed.
Power Spot 575™ WARRANTY REGISTRATION: The Power Spot 575™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number.
Never touch the fixture during normal operation. This can cause severe personal injuries and/or damage to the fixture. Be sure to unplug the POWER SPOT 575™ from the power outlet before performing any service related issues. Lamp Replacement; Allow at least 30 minutes after disconnecting main power before you open the POWER SPOT 575™.
2.1.1 Clamps The POWER SPOT 575™ has been designed to hold multiple clamps to the bottom of the unit in several different orientations. Always use an appropriately rated clamp to mount this unit to truss. Refer to the printed instructions on the bottom of the fixture for proper clamp installation.
DMX chain. 2.5 Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The POWER SPOT 575™ can be controlled via DMX-512 protocol. The POWER SPOT 575™ is a 15 channel DMX fixture. The DMX address is set electronically using the controls on the side panel of the fixture.
The chart below details a proper cable conversion. Fuse Requirements The POWER SPOT 575 electronic system is protected by a 5x20 mm external fuse: 250v / 10A (US model) or 230V / T 5 A (EU model). The fuse requirements are clearly printed on the side of the fixture.
Master for the audio program SVPT Basic position for the audio program SIZE Size for the audio program (NORM-BIG-MIDL-SMAL) LAMP Switch on/of the lamp direct at the Power Spot 575 RESE Reset TIME POWR Running time of the fixture (non destructible)
DMX signal the display will flash continuously. D001 To set or adjust a DMX address, please follow the procedure below: 1. Switch on the POWER SPOT 575™ and wait for the fixture reset process to RESE finished (' ' will flash in the LED while fixture is in reset mode).
Feedback 3.9.10 Feedback ”APC” FEED The POWER SPOT 575™ is equipped with ”APC,” automatic position correction. This function automatically corrects the Pan and Tilt movement should the unit lose step or is obstructed and forced to lose step. Press the Enter button to access the sub-menu.
Power Spot 575™ Operation Operating Modes: The Power Spot 575™ can operate in three different modes. This next section will detail the differences in the operating modes. • Stand alone mode - The fixture will react to sound, chasing through the built-in programs.
• Wait min. 20 minutes after the last operation to cool down the fixture. • Don’t touch the bulb of the lamp with bare fingers (this can cause damages. • Before you put the POWER SPOT 575™ into operation close the casing, otherwise your retina can be hurt! 6.2 Lamp Change...
Power Spot 575™ Changing/Replacing Gobos The POWER SPOT 575™ is fitted with a standard size gobo wheel that accepts gobos with an outside diameter of 27mm and a viewable image size of 23mm. Glass or steel gobos may be used. Please follow the safety procedures and installation below for proper...
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances should alcohol or solvents be used! The inside optical system should be maintained only by authorized persons. Please contact Elation professionals for recommendation associated with internal cleaning procedures. 9.1 Safety Regulations •...
United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professionals shall have no liability whatsoever for loss of or damage to any such ®...
Page 42
The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professionals be liable for any loss or damage, direct or consequential, arising out of the ®...
Page 47
Power Spot 575™ Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax www.ElationLighting.com / info@ElationLighitng.com...