Ford 2016 EXPEDITION Owner's Manual

Table of Contents

Quick Links

Download this manual

2016 EXPEDITION Owner's Manual

owner.ford.com

ford.ca

June 2015

First Printing

Owner's Manual

Expedition

Litho in U.S.A.

I n f o r ma t i o n P r o v i d e d b y :

GL1J 19A321 AA

Table of Contents

Troubleshooting

Summary of Contents for Ford 2016 EXPEDITION

Page 1 2016 EXPEDITION Owner’s Manual owner.ford.com ford.ca June 2015 First Printing Owner’s Manual Expedition Litho in U.S.A. I n f o r ma t i o n P r o v i d e d b y : GL1J 19A321 AA...
Page 2 No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2015 All rights reserved. Part Number: 20150508195124...
Page 3 I n f o r ma t i o n P r o v i d e d b y :...
Page 4: Table Of Contents
About This Manual...........7 Symbols Glossary..........7 Keys and Remote Controls Data Recording..........9 Principle of Operation........41 California Proposition 65......11 General Information on Radio Perchlorate............11 Frequencies...........41 Ford Credit............11 Remote Control..........42 Replacement Parts Replacing a Lost Key or Remote Recommendation........11 Control............45 Special Notices..........12 Mobile Communications MyKey Equipment.............12...
Page 5 Table of Contents Adjusting the Steering Wheel - Vehicles Warning Lamps and Indicators....88 With: Power Adjustable Steering Audible Warnings and Indicators....91 Column............67 Audio Control..........68 Information Displays Voice Control...........69 General Information........92 Cruise Control..........70 Information Messages........103 Information Display Control.......70 Heated Steering Wheel........70 Climate Control Manual Climate Control......113 Pedals...
Page 6 Table of Contents Using Stability Control........177 Starting and Stopping the Engine Terrain Response General Information........145 Using Hill Descent Control......179 Ignition Switch..........145 Keyless Starting..........145 Parking Aids Starting a Gasoline Engine.......146 Principle of Operation........181 Engine Block Heater........149 Rear Parking Aid..........181 Fuel and Refueling Front Parking Aid..........182 Rear View Camera........183 Safety Precautions........151...
Page 7 Table of Contents Economical Driving........220 Transfer Case Fluid Check......251 Driving Through Water........221 Brake Fluid Check.........251 Floor Mats............221 Washer Fluid Check........252 Fuel Filter............252 Roadside Emergencies Changing the 12V Battery......252 Roadside Assistance........223 Checking the Wiper Blades.....254 Hazard Warning Flashers......224 Changing the Wiper Blades.....255 Fuel Shutoff...........224 Adjusting the Headlamps......255 Jump Starting the Vehicle......225...
Page 8 Table of Contents Motorcraft Parts..........303 Appendices Vehicle Identification Number....305 End User License Agreement....391 Vehicle Certification Label......306 Transmission Code Designation...306 Capacities and Specifications - 3.5L Ecoboost ..........307 Audio System General Information........312 Audio Unit - Vehicles With: AM/FM/CD/ SYNC/Satellite Radio......313 Audio Unit - Vehicles With: Sony AM/FM/ CD..............315 Digital Radio............317 Satellite Radio..........319...
Page 9 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 10: Introduction
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about your vehicle, the greater the safety and pleasure you will get from driving it.
Page 11 Introduction Brake system Front airbag Cabin air filter Front fog lamps Check fuel cap Fuel pump reset Child safety door lock or unlock Fuse compartment Hazard warning flashers Child seat lower anchor Heated rear window Child seat tether anchor Heated windshield Cruise control E71340 Interior luggage compartment...
Page 12: Data Recording
Parking brake Additionally, when your vehicle is in for service or repair, Ford Motor Company, Ford of Canada, and service and repair Power steering fluid facilities may access or share among them data for vehicle improvement purposes.
Page 13 If you do not want other government authorities or other Ford or its vendors to receive this third parties acting with lawful information, do not activate the authority. Other parties may seek to service.
Page 14: California Proposition 65
Ford replacement collision parts meet our stringent requirements for fit, finish, (U.S. Only) structural integrity, corrosion protection Ford Credit offers a full range of financing and dent resistance. During vehicle and lease plans to help you acquire your development we validate these parts vehicle.
Page 15: Special Notices
We do not recommend or endorse the use caused to your vehicle as a result of the of any non-Ford-approved aftermarket failure of non-Ford parts may not be OBD plug-in devices. The vehicle Warranty covered by the Ford Warranty. For...
Page 16: Export Unique Options
Introduction EXPORT UNIQUE OPTIONS For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’s Manual. A market unique supplement may be supplied that complements this book.
Page 17: Environment
Environment PROTECTING THE ENVIRONMENT You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim. I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 18: Child Safety
Ford recommends Exposure of people or animals to these checking with a NHTSA Certified Child high temperatures for even a short time...
Page 19: Installing Child Restraints
Child Safety Recommendations for Safety Restraints for Children Child Child size, height, weight, or age Recommended restraint type Infants or Children weighing 40 lb (18 kg) or less Use a child safety seat toddlers (generally age four or younger). (sometimes called an infant carrier, convertible seat, or toddler seat).
Page 20: Child Safety
Child Safety Use a child safety seat (sometimes called • Place the vehicle seat upon which the an infant carrier, convertible seat, or child seat will be installed in the upright toddler seat) for infants, toddlers, or position. children weighing 40 pounds (18 •...
Page 21 Child Safety E142530 E142875 3. While holding the shoulder and lap belt 5. To put the retractor in the automatic portions together, route the tongue locking mode, grasp the shoulder through the child seat according to the portion of the belt and pull downward child seat manufacturer's instructions.
Page 22 Child Safety Using Lower Anchors and Tethers 8. Remove remaining slack from the belt. for CHildren (LATCH) Force the seat down with extra weight, for example, by pressing down or WARNING kneeling on the child restraint while pulling up on the shoulder belt in order Never attach two child safety seats to force slack from the belt.
Page 23: Using Tether Straps
Child Safety The locator symbols are on round plastic buttons for the center seat and on rectangular tags for the outboard seats. Follow the instructions on attaching child safety seats with tether straps. See Using Tether Straps in this chapter. Attach LATCH lower attachments of the child seat only to the anchors shown.
Page 24 Child Safety Some of the rear seats of your vehicle are Once the child safety seat has been equipped with built-in tether strap anchors installed using either the safety belt, the located behind the seats as described lower anchors of the LATCH system, or below.
Page 25 Child Safety For center seating positions, route the child safety seat tether strap over the back of the seat. For outboard seating positions, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, recline the seat back slightly to obtain proper fit.
Page 26: Booster Seats
Child Safety BOOSTER SEATS WARNING Never place, or allow a child to place, the shoulder belt under a child's arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
Page 27: Types Of Booster Seats
Child Safety • Can the child sit all the way back against their vehicle seat back with knees bent comfortably at the edge of the seat cushion? • Can the child sit without slouching? • Does the lap belt rest low across the hips? •...
Page 28: Child Restraint Positioning
Child Safety E142596 E142597 WARNINGS If the booster seat slides on the vehicle the way back. When possible, all children seat upon which it is being used, placing a age 12 and under should be properly rubberized mesh sold as shelf or carpet restrained in a rear seating position.
Page 29: Child Safety Locks
Child Safety WARNINGS WARNINGS manufacturer. A safety seat that is Always restrain an unoccupied child improperly installed or utilized, is seat or booster seat. These objects inappropriate for your child's height, age, may become projectiles in a crash or or weight or does not properly fit the child sudden stop, which may increase the risk may increase the risk of serious injury or of serious injury.
Page 30 Child Safety E205034 The locks are located on the rear edge of each rear door and must be set separately for each door. Move the lock control up to engage the lock. Move it down to disengage the lock. I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 31: Seatbelts
Seatbelts PRINCIPLE OF OPERATION WARNINGS When possible, all children 12 years old and under should be properly WARNINGS restrained in a rear seating position. Always drive and ride with your Failure to follow this could seriously seatback upright and the lap belt increase the risk of injury or death.
Page 32: Fastening The Seatbelts
Seatbelts The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal crashes, the safety belt pretensioners may be activated alone or, if the crash is of sufficient severity, together with the front airbags.
Page 33: Safety Belt Locking Modes
Seatbelts Pregnant women should always wear their Vehicle Sensitive Mode safety belt. The lap belt portion of a This is the normal retractor mode, which combination lap and shoulder belt should allows free shoulder belt length be positioned low across the hips below adjustment to your movements and the belly and worn as tight as comfort will locking in response to vehicle movement.
Page 34: Seatbelt Height Adjustment
Seatbelts How to Use the Automatic Locking Use only extensions manufactured by the Mode same supplier as the safety belt. Manufacturer identification is on a label located either at the end of the webbing or on the retractor behind the trim. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.
Page 35: Seatbelt Warning Lamp And Indicator Chime
Seatbelts Second Row Comfort Guide WARNING Position the safety belt comfort guide so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash. E205037 To adjust the comfort guide: Slip the shoulder belt into the belt...
Page 36: Seatbelt Reminder
Seatbelts Conditions of operation If... Then... The driver's safety belt is not buckled The safety belt warning light illuminates 1- before the ignition switch is turned to the 2 minutes and the warning chime sounds on position... 4-8 seconds. The driver's safety belt is buckled while the The safety belt warning light and warning indicator light is illuminated and the chime turn off.
Page 37: Child Restraint And Seatbelt Maintenance
• The transmission is in park (P). specific to the child restraint. • The ignition is off. Ford Motor Company recommends that • All vehicle doors are closed. all safety belt assemblies in use in vehicles • The driver safety belt is unbuckled.
Page 38: Supplementary Restraints System
Supplementary Restraints System The airbags are a supplemental restraint PRINCIPLE OF OPERATION system and are designed to work with the safety belts to help protect the driver and WARNINGS right front passenger from certain upper Airbags do not inflate slowly or body injuries.
Page 39: Driver And Passenger Airbags
Supplementary Restraints System Restraint Safety System module. During a crash, the restraints control module may activate the safety The restraint safety system provides an belt pretensioners and/or either one or improved overall level of frontal crash both stages of the dual-stage airbag protection to front seat occupants and is supplemental restraints based on crash designed to help further reduce the risk of...
Page 40: Side Airbags
Supplementary Restraints System · Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator (page 39). Proper Driver and Front Passenger Seating Adjustment WARNING The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 in E142846 (25 cm) between an occupant’s chest and Children must always be properly...
Page 41: Safety Canopy
Supplementary Restraints System ·Crash sensors and monitoring WARNINGS system with readiness indicator. Do not attempt to service, repair, or See Crash Sensors and Airbag modify the airbag, its fuses or the Indicator (page 39). seat cover on a seat containing an airbag as you could be seriously injured or The design and development of the side killed.
Page 42: Crash Sensors And Airbag Indicator
Supplementary Restraints System The system consists of the following: WARNINGS • Safety canopy curtain airbags located To reduce risk of injury, do not above the trim panels over the front obstruct or place objects in the and rear side windows identified by a deployment path of the curtain label or wording on the headliner or airbag.
Page 43: Airbag Disposal
Supplementary Restraints System Your vehicle has a collection of crash and The fact that the safety belt pretensioners occupant sensors which provide or front airbags did not activate for both information to the restraints control front seat occupants in a crash does not module which deploys (activates) the mean that something is wrong with the front safety belt pretensioners, driver...
Page 44: Keys And Remote Controls
Keys and Remote Controls • Structures around the vehicle. PRINCIPLE OF OPERATION • Other vehicles parked next to your The remote control allows you to: vehicle. • Remotely lock or unlock the vehicle The radio frequency used by your remote doors.
Page 45: Remote Control
Keys and Remote Controls REMOTE CONTROL Integrated Keyhead Transmitter Equipped) E138616 The intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to use the push button start. E210695 Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle.
Page 46: Keys And Remote Controls
Keys and Remote Controls Replacing the Battery 3. Insert the new battery. Refer to the symbols inside the transmitter for the Note: Refer to local regulations when correct orientation of the battery. disposing of transmitter batteries. Press the battery down to make sure it is fully in the housing.
Page 47: Car Finder
Keys and Remote Controls 4. Insert a new battery with the + facing This feature allows you to start your downward. Press the battery down to vehicle from the outside. The transmitter make sure it is fully in the housing. has an extended operating range.
Page 48: Replacing A Lost Key Or Remote Control
Keys and Remote Controls Turning Your Vehicle Off After Remote To start your vehicle remotely: Starting Press the lock button to lock all the doors. Press the button once. The parking lamps turn off. 2. Press the remote start button twice. E138625 The exterior lamps flash twice.
Page 49: Mykey
MyKey • Driver assist features, if equipped on PRINCIPLE OF OPERATION your vehicle, are forced on: parking aid, blind spot information system (BLIS) MyKey allows you to program keys with with cross traffic alert, lane departure restricted driving modes to promote good warning and forward collision warning driving habits.
Page 50: Creating A Mykey
MyKey • Various vehicle speed minders can be CREATING A MYKEY set. Once you select a speed, it will be shown in the display, followed by an Use the information display to create a audible tone when the preselected MyKey: vehicle speed is exceeded.
Page 51: Clearing All Mykeys
MyKey Note: You can clear or change your MyKey CLEARING ALL MYKEYS settings at any time during the same key cycle as you created the MyKey. Once you You can clear or change your MyKey have switched the vehicle off, however, you settings using the information display will need an admin key to change or clear control on the steering wheel.
Page 52: Checking Mykey System Status
MyKey You can find information on programmed CHECKING MYKEY SYSTEM MyKey(s) using the information display STATUS control on the steering wheel. See Information Displays (page 92). To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to: Message Description Settings...
Page 53: Using Mykey With Remote Start Systems
Systems start systems. If you choose to install a remote start system, see an authorized When using a Ford-approved aftermarket dealer for a Ford-approved remote start remote start system, the vehicle recognizes system. the remote start system transmitter as an The following information may help if you additional admin key.
Page 54: Mykey Troubleshooting
MyKey 2. Start your vehicle using your After clearing your MyKeys, you can create non-Ford-approved remote start a new MyKey. See Creating a MyKey system transmitter. (page 47). 3. See Clearing All MyKeys (page 48). Note: With push-button start, you cannot Follow Steps 1-3.
Page 55 MyKey Condition Potential Causes I lost a key. Program a spare transmitter. See Passive Anti-Theft System (page 62). I accidentally programmed all keys as The vehicle has a remote start system trans- MyKeys. mitter that is recognized as an admin key. Clear all MyKeys by using the remote start trans- mitter.
Page 56: Locks
Locks unlocking mode applies to the remote LOCKING AND UNLOCKING control, keyless entry keypad and intelligent access. You can also change You can use the power door lock control between the unlocking modes using the or the remote control to lock and unlock information display.
Page 57: Auto Relock
Locks At the Liftgate To do this, lock your vehicle after you have closed all the doors by: The liftgate unlocks and opens • Using the keyless entry keypad. automatically when you press the liftgate release button. • Pressing the lock button on another intelligent access key.
Page 58: Manual Liftgate
Locks Autounlock The lamps will turn off if all the doors remain closed and: Autounlock unlocks all the doors when all • 25 seconds have elapsed. of the following occur: • You press the push button ignition • The ignition is on, all the doors are switch.
Page 59: Opening The Liftgate Window
Locks Note: Be careful when opening or closing With the Remote Control the liftgate in a garage or other enclosed Press twice within three seconds area to avoid damaging the liftgate. to unlatch the liftgate. Note: Do not hang anything, for example E138630 a bike rack, from the glass or liftgate.
Page 60: Power Liftgate
Locks Closing the Liftgate WARNINGS Keep keys out of reach of children. Do not allow children to operate or play near an open or moving power liftgate. You should supervise the operation of the power liftgate at all times. Note: Make sure that you close the liftgate before operating or moving your vehicle, especially in an enclosure, like a garage or a parking structure.
Page 61: Opening And Closing The Liftgate
Locks Opening and Closing the Liftgate WARNING Make sure all persons are clear of the power liftgate area before using the power liftgate control. Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not leave the liftgate open while driving.
Page 62: Keyless Entry
Locks Obstacle Detection When Closing The system stops when it detects an obstacle. Three chimes sound and the system reverses to open. Once you remove the obstacle, you can power close the liftgate. Note: Entering your vehicle while the liftgate is closing can cause your vehicle to bounce and activate obstacle detection.
Page 63 Locks You can use the keypad to lock or unlock Tips: the doors without using a key. • Do not set a code that uses five of the same number. For vehicles without intelligent access, you can operate the keypad with the •...
Page 64: Unlocking And Locking The Doors
Locks Displaying the Factory Set Code Note: You must have an intelligent access key within 3 ft (1 m) of your vehicle. Note: You will need to have two programmed passive anti-theft keys for this procedure. To display the factory-set code in the information display: Insert a key into the ignition and switch the ignition on for a few seconds.
Page 65: Security
Note: Your vehicle comes equipped with two integrated keyhead transmitters or two Note: The system is not compatible with intelligent access keys. non-Ford aftermarket remote start systems. The integrated keyhead transmitter Use of these systems may result in vehicle functions as a programmed ignition key...
Page 66: Anti-Theft Alarm
Security You must have two previously Programming a Spare Intelligent programmed coded keys and the new Access Key unprogrammed key readily accessible. See See your authorized dealer to have your authorized dealer to have the spare additional keys programmed to your key programmed if two previously vehicle.
Page 67: Power Running Boards
Power Running Boards (If Equipped) Automatic Power Deploy USING POWER RUNNING BOARDS WARNINGS In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Make sure that the running boards have deployed, and have finished moving before attempting to step on them.
Page 68 Power Running Boards (If Equipped) • When disabled (OFF), the running boards move to the stowed position regardless of the door position. • When enabled (AUTO), the running boards move back to the correct positions based on the door position. Bounce-back The running board will reverse direction and move to the end of travel if it...
Page 69: Steering Wheel
Steering Wheel ADJUSTING THE STEERING WHEEL - VEHICLES WITH: COLUMN SHIFT/MANUAL ADJUSTABLE STEERING COLUMN WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 122).
Page 70: Adjusting The Steering Wheel - Vehicles With: Power Adjustable Steering Column
Steering Wheel ADJUSTING THE STEERING WHEEL - VEHICLES WITH: POWER ADJUSTABLE STEERING COLUMN Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 122). WARNING Do not adjust the steering wheel when your vehicle is moving. E183047 Unlock the steering column.
Page 71: Audio Control
Steering Wheel End of Travel Position AUDIO CONTROL (If Equipped) The steering column sets a stopping Operate the following functions with the position just short of the end of the column control: position to prevent damage to the steering column. A new stopping position sets if the Type One steering column encounters an object when tilting or telescoping.
Page 72: Voice Control
Steering Wheel Type Two Press and hold the seek button to: • Tune the radio to the next station up or down the frequency band. • Seek through a track. VOICE CONTROL (If Equipped) Type One E205756 Volume up. Seek up or next. Media.
Page 73: Cruise Control
Steering Wheel Type Two CRUISE CONTROL E205805 See Cruise Control (page 186). INFORMATION DISPLAY CONTROL E205758 Phone mode. Voice recognition. See SYNC (page 323). E205806 See Information Displays (page 92). HEATED STEERING WHEEL Equipped) See your MyFord Touch information. I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 74: Pedals
Pedals (If Equipped) ADJUSTING THE PEDALS WARNING Never use the controls while your feet are on the accelerator and brake pedals and the vehicle is moving. You can find the control on the left side of the steering column. Press and hold the appropriate side of the control to move the pedals.
Page 75: Wipers And Washers
Wipers and Washers Note: Clean the windshield and wiper WINDSHIELD WIPERS blades if they begin to leave streaks or smears. If that does not resolve the issue, Note: Fully defrost the windshield before install new wiper blades. See Changing you switch the windshield wipers on. the Wiper Blades (page 255).
Page 76: Windshield Washers
Wipers and Washers Keep the outside of the windshield clean. REAR WINDOW WIPER AND The rain sensor is very sensitive. If the area WASHERS around the mirror is dirty, then the wipers may operate if dirt, mist or insects hit the Rear Window Wiper windshield.
Page 77: Lighting
Lighting GENERAL INFORMATION LIGHTING CONTROL Condensation in Lamp Assemblies Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold.
Page 78: Autolamps
Lighting Headlamp Flasher If equipped, the following also activate when the lighting control is in the autolamps position and you switch them on in the information display: • Configurable daytime running lamps. • Automatic high beam control. • Adaptive headlamp control. The headlamps remain on for a period of time after you switch the ignition off.
Page 79: Instrument Lighting Dimmer
Lighting INSTRUMENT LIGHTING DAYTIME RUNNING LAMPS DIMMER Equipped) WARNING The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog.
Page 80: Front Fog Lamps
Lighting 3. The transmission is not in park (P) for DIRECTION INDICATORS vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions. 4. The lighting control is in the autolamps position. 5. The headlamps are off. The other lighting control switch positions do not activate the daytime running lamps, and you can use them to temporarily...
Page 81: Interior Lamps
Lighting INTERIOR LAMPS Front Row Map Lamps (If Equipped) Press the switches on either side of each map lamp to turn on the lamps. The map lamps light when: • any door is opened. • the instrument panel dimmer switch is pressed up until the courtesy lamps come on.
Page 82: Ambient Lighting
Lighting Rear Cargo Lamp The rear cargo lamps light when: • any door is opened, and the switch is in the middle position. • the instrument panel dimmer switch is pressed up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is off (and the switch is in the middle position).
Page 83: Windows And Mirrors
Windows and Mirrors Overriding the Bounce-Back Feature POWER WINDOWS WARNING WARNINGS When you override the bounce-back Do not leave children unattended in feature the window will not reverse your vehicle and do not let them play if it detects an obstacle. Take care with the power windows.
Page 84: Exterior Mirrors
Windows and Mirrors Power-Folding Mirrors EXTERIOR MIRRORS (If Equipped) Power Exterior Mirrors WARNING Do not adjust the mirrors when your vehicle is moving. E163060 Note: Moving the mirrors 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the control down during full travel, may disable the system to protect the motors from overheating.
Page 85: Interior Mirror
Windows and Mirrors Heated Exterior Mirrors Auto-Dimming Mirror See Heated Windows and Mirrors (page Note: Do not block the sensors on the front 121). and back of the mirror. Mirror performance may be affected. A rear center passenger or Memory Mirrors raised rear center head restraint may also (If Equipped) block light from reaching the sensor.
Page 86: Rear Quarter Windows
Windows and Mirrors The rear view mirror may have to be SUN VISORS adjusted to its lower arm position to prevent interference when the childminder mirror is extended down. REAR QUARTER WINDOWS Equipped) WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows.
Page 87: Windows And Mirrors
Windows and Mirrors Bounce-Back WARNINGS When closing the moonroof, you The moonroof will stop automatically should verify that it is free of while closing. It will reverse some distance obstructions and make sure that if there is an obstacle in the way. children and pets are not in the proximity Pull and hold the SLIDE control within two of the roof opening.
Page 88: Instrument Cluster
Instrument Cluster GAUGES Type 1 and 2 E205349 Tachometer. Information display (Type 2 shown Type 1 similar). Speedometer. Fuel gauge. Engine coolant temperature gauge. Outside Air Temperature Information Display Shows the outside air temperature. Odometer Trip Computer Located in the bottom of the information I n f o r ma t i o n P r o v i d e d b y : display.
Page 89: Expedition (Tb7) Canada/United States Of America, Enusa, First Printing
Instrument Cluster Vehicle Settings and Personalization Note: If the gas station nozzle shuts off before the tank is full, try a different gas See General Information (page 92). pump nozzle. Fuel Gauge Note: There is a small reserve left in the tank when the fuel gauge reaches empty.
Page 90: Expedition (Tb7) Canada/United States Of America, Enusa, First Printing
Instrument Cluster Type 3 E205350 Left Information Display. Speedometer. Right Information Display. See SYNC (page 323). Vehicle Settings and Personalization Left Information Display See General Information (page 92). Odometer Located in the bottom of the information display. Registers the accumulated distance your vehicle has traveled.
Page 91: Warning Lamps And Indicators
Instrument Cluster WARNING LAMPS AND WARNING INDICATORS Driving a vehicle with the brake system warning light on is dangerous. The following warning lamps and A significant decrease in braking indicators alert you to a vehicle condition performance may occur. It will take you that may become serious.
Page 92: Engine Oil
Instrument Cluster Engine Oil Liftgate Ajar If it illuminates with the engine Lights when the liftgate is not running or when you are driving, completely closed. this indicates a malfunction. E162453 Stop your vehicle as soon as it is safe to Low Fuel Level do so and switch the engine off.
Page 93: Instrument Cluster
Instrument Cluster Service Engine Soon Stability Control System If the service engine soon Displays when the indicator light stays illuminated AdvanceTrac®/Traction control after you start the engine, it is active. If the light remains on, E138639 indicates that the On Board Diagnostics have the system serviced immediately.
Page 94: X4 Low
Instrument Cluster 4X4 LOW Illuminates when you engage four-wheel drive low. If the light fails to display or remains on E163174 when the ignition is on, have the system serviced immediately by an authorized dealer. 4X4 HIGH Illuminates when you engage four-wheel drive high.
Page 95: Information Displays
Information Displays • Press the up and down arrow buttons GENERAL INFORMATION to scroll through and highlight the options within a menu. WARNING • Press the right arrow button to enter a Driving while distracted can result in sub-menu. loss of vehicle control, crash and •...
Page 96: Information Displays
Information Displays Display Mode Distance to E Digital Speedo Oil Press Oil Temp Trans Temp Note: Pressing OK stops/starts the timer. Trip 1 & 2 Holding OK resets the odometer and timer. Use the arrow buttons to choose between the following. Trip 1 &...
Page 97 Information Displays Driver Assist DTE Calculation Normal history used or Towing history used Engine Hours Engine Hours XXXXX Engine Idle Hours Engine Idle Hours XXXXX Note: Some items are optional and may Settings not appear. In this mode, you can configure different driver setting choices.
Page 98 Information Displays Settings Volume Limiter - check enabled or uncheck disabled Do Not Disturb Always On or User Selectable Clear MyKeys Hold OK to Clear All MyKeys Display Setup Distance Miles & Gallons, L/100km or km/L Temperature Fahrenheit or Celsius Language Select Language - Hold OK to set language *Some MyKey items only appear if a MyKey is set.
Page 99 Information Displays Trip/Fuel Trip 1 or Trip 2 Fuel Economy Fuel History • Trip 1 or Trip 2 - Shows your trip time, Towing fuel used, odometer and average mpg. Use the arrow buttons to configure • Fuel Economy - Shows your different towing setting choices.
Page 100 Information Displays Towing Delete Trailer List of named trailers — Hold OK to Delete Add Trailer Naming Editor Connection Checklist Ball Coupler Connected and Locked? Electrical Wiring Connect? Lights Function Correctly? Safety Chains Connected? Tongue Jack Raised? Mirrors Adjusted? TBC gain setting adjusted? Trailer Disconnected? Trailer Setup Go to start of Add Trailer Process...
Page 101 Information Displays Settings Driver Select Sport, Normal or Comfort Suspension DTE Calculation Normal history used or Towing history used Advanced Vehicle Lighting Autolamp Delay Select time Settings interval Locks Autolock - check enabled or uncheck disabled Autounlock - check enabled or uncheck disabled Remote Unlock Driver’s Door or...
Page 102 Information Displays Settings Temperature °Fahrenheit or °Celsius Language Select Language - Hold OK to Set *Some MyKey items only appear if a MyKey is set. The arrows in the upper left corner of the Information Display Controls display indicate additional content (Type 3) available when lit.
Page 103 Information Displays Display Mode Oil Life Distance to Empty Digital Speedometer - Press OK to change the currently units displayed Note: Press and hold OK to reset the Trip/Fuel currently displayed information. Use the arrow buttons to choose between the following trip and fuel options. Trip/Fuel Trip 1 or Trip 2 Fuel Economy...
Page 104 Information Displays Towing Press OK to change the selected trailer Change Trailer Settings Rename Trailer Reset Trailer Mileage Delete Trailer Trailer Setup Add Trailer Naming Editor Connection Checklist Ball Coupler Connected and Locked? Electrical Wiring Connect? Lights Function Correctly? Safety Chains Connected? Tongue Jack Raised? Mirrors Adjusted? TBC gain setting adjusted?
Page 105 Information Displays Blindspot - check enabled or uncheck disabled Cross Traffic Alert - check enabled or uncheck disabled Driver Select Sport, Normal or Comfort Suspension DTE Calculation Normal or Towing Front Park Aid - check enabled or uncheck disabled Rear Park Aid - check enabled or uncheck disabled Advanced Vehicle Easy Entry / Exit - check enabled or uncheck disabled...
Page 106: Information Messages
Information Displays MyKey* MyKey Status Number of Admin Keys, MyKeys and MyKey Mileage Create MyKey Hold OK to Create MyKey 911 Assist Always On or User Selectable Do Not Disturb Always On or User Selectable Traction Control Always On or User Selectable Max Speed 65 MPH (105 km/h), 70 MPH (110 km/h), 75 MPH (120 km/h), 80...
Page 107: Alarm Messages
Information Displays AdvanceTrac / Traction Control Messages Message Action Traction control off/ Displays when you switch the traction control system off or Traction control on on. See Using Traction Control (page 175). Service AdvanceTrac Displays when the system detects a condition that requires service.
Page 108: Brake System Messages
Information Displays Blind Spot Information System Messages Message Action Blindspot Not Available Displays when the blind spot information system/cross traffic Sensor Blocked See alert system sensors are blocked. Driver can typically clean Manual the sensor to resolve. Blindspot System Fault Displays when a fault with the blind spot information system occurs.
Page 109: Engine Messages
Information Displays Engine Messages Message Action Power Reduced to Lower Engine Displays when the engine has reduced power to help Temp reduce high engine temperature. Engine On Informs you that you are exiting your vehicle and the engine is on. Fuel Messages Message Action...
Page 110: Maintenance Messages
Information Displays Message Action Restart Now or Key is Displays when you press the start/stop button to shut off the Needed engine and an Intelligent Access Key is not detected inside the vehicle. Accessory Power Active Displays when the vehicle is in the accessory ignition state. Starting System Fault This message displays when there is a problem with your vehicle’s starting system.
Page 111: Off Road Messages
Information Displays MyKey Messages Message Action MyKey active Drive Displays when MyKey is active. Safely Speed Limited to xx Displays when starting the vehicle and MyKey is in use and MPH/km/h the MyKey speed limit is on. Near Vehicle Top Speed Displays when a MyKey is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h).
Page 112: Park Aid Messages
Information Displays Message Action For Hill Descent Select Gear Displays when hill descent control mode requires driver shift transmission into gear. Hill Descent Driver Resume Displays when the hill control mode requires the driver Control to resume control. Hill Descent Control FAULT Displays when a hill descent system fault is present.
Page 113: Remote Start Messages
Information Displays Remote Start Messages Message Action To Drive: Turn Key to On Displays as a reminder to turn the key to on to drive the vehicle after a remote start. To Drive: Press Brake Displays as a reminder to apply the brake and the start button and START Button to drive the vehicle after a remote start.
Page 114: Transmission Messages
Information Displays Message Action Trailer Disconnected Displays when a trailer connection becomes discon- nected, either intentionally or unintentionally, and the system senses it during a given ignition cycle. Disregard this status if your vehicle is not equipped with a factory installed trailer brake controller.
Page 115: Wd Messages
Information Displays 4WD Messages Message Action Check 4X4 Displays when a 4X4 system fault is present. 4X4 Shift In Progress Displays when the 4X4 system is making a shift. For 4X4 Low Apply Brake Displays when trying to select 4X4 Low. For 4X4 Low Shift to N Displays when you select 4X4 LOW with the vehicle stopped.
Page 116: Climate Control
Climate Control MANUAL CLIMATE CONTROL E205762 Fan speed control: Adjust the volume of air circulated in the vehicle. Temperature control: Controls the temperature of the air circulated in your vehicle. Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off.
Page 117: Manual Climate Control - Vehicles With: Electronic Manual Temperature Control (Emtc)
Climate Control Note: Recirculated air may also turn on and off automatically in instrument panel or instrument panel and floor airflow modes during hot weather to improve cooling efficiency. A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air.
Page 118 Climate Control Defrost: Select to distribute air through the windshield air vents. Air distribution to the instrument panel and footwell vents turns off. You can also use this setting to defrost and clear the windshield of a thin covering of ice. A/C: Press the button to switch the air conditioning on or off.
Page 119: Automatic Climate Control
Climate Control AUTOMATIC CLIMATE CONTROL E205763 Power and Driver temperature control: Press the button to switch the system on and off. When the system is off, it prevents outside air from entering the vehicle. Adjusts the temperature setting using the control on the driver side. Climate controlled seats: Press the button to switch the climate controlled seats on and off.
Page 120: Hints On Controlling The Interior Climate
Climate Control MAX A/C: Press the button for maximum cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on and the fan automatically adjusts to the highest speed. Recirculated air: Press the button to switch between outside air and recirculated air.
Page 121: Heating The Interior Quickly
Climate Control Automatic Climate Control Note: If you select AUTO during cold outside temperatures, the system directs Note: Adjusting the settings when your airflow to the windshield and side window vehicle interior is extremely hot or cold is vents. In addition, the fan may run at a not necessary.
Page 122: Cooling The Interior Quickly
Climate Control Cooling the Interior Quickly Vehicle with manual climate control Vehicle with automatic climate control Adjust the temperature control to the Press the MAX A/C button. MAX A/C position. Drive with the windows fully open until you feel cold air through the air vents. Recommended Settings for Cooling Vehicle with manual climate control Vehicle with automatic climate control...
Page 123: Rear Passenger Climate Controls
Climate Control REAR PASSENGER CLIMATE CONTROLS E188689 Fan speed control: Adjust the volume of air circulated in the vehicle. Heated seats (if equipped): Press the button to switch the heated seats on and off. See Heated Seats (page 134). Temperature control: Control the temperature of the air circulated in your vehicle.
Page 124: Heated Windows And Mirrors
Climate Control Turn the ignition on to return the system HEATED WINDOWS AND to its previous settings. You can now make MIRRORS adjustments normally, but you need to turn certain vehicle-dependent features back Heated Rear Window on, such as: • Heated seats.
Page 125: Seats
Seats We recommend that you follow these SITTING IN THE CORRECT guidelines: POSITION • Sit in an upright position with the base of your spine as far back as possible. WARNINGS • Do not recline the seatback more than Sitting improperly, out of position or 30 degrees.
Page 126: Adjusting The Head Restraint
Seats Lowering the Head Restraint WARNINGS Install the head restraint properly to Press and hold button C. help minimize the risk of neck injury 2. Push the head restraint down. in the event of a crash. Removing the Head Restraint Note: Adjust the seatback to an upright Pull the head restraint up until it driving position before adjusting the head...
Page 127: Manual Seats
Seats Second Row Center Seat Head WARNINGS Restraint Rock the seat backward and forward after releasing the lever to make sure The center rear head restraint is fixed and that it is fully engaged. non-adjustable. The head restraint consists of a trimmed foam covering over the upper structure of the seatback.
Page 128: Power Seats
Seats E181777 The control is located on the outboard side of the seat. Move the switch in the direction of the arrow to raise or lower the seat E205041 cushion or to move the seat forward, Manual Lumbar backward, up or down. (If Equipped) Power Recline (If Equipped)
Page 129: Memory Function
Seats 2. Continue pressing the control until it reaches the end of the seat track. 3. Continue pressing the control for about two seconds. You will feel the seat bounce back slightly. Power Lumbar (If Equipped) E205043 Saving a PreSet Position Switch the ignition on.
Page 130: Rear Seats
Seats Easy Entry and Exit Feature You can also recall a preset memory position by: Equipped) • Pressing the unlock button on your This feature adjusts the position of the seat remote control if it is linked to a preset and steering column to allow easier exit position.
Page 131 Seats Move the front passenger seat forward so that the second row seat head restraint clears the front seat. E205045 Lift the seatback toward the rear of the vehicle. E190842 2. Rotate the seatback until you hear a click, locking it in the upright position. Lower the head restraints by pulling on the strap.
Page 132 Seats Place the second-row seats in a kneel 2. Return the seatback to the upright down load floor position to allow more position. cargo space. Adjusting the Second Row To place the seats in the cargo mode: Outboard 40% Seat for E-Z Entry Fold down the second row seat.
Page 133: Exiting The Third Row
Seats Fold down the second row seat and Note: If a squeak is heard from the latch release the handle. area, the latch striker pin should be wiped clean of dust or debris. 2. Pull the handle up again until the seat releases from the floor.
Page 134 Seats E205053 E205054 The release handle is located on the Locate the release handle in the upper outboard side of the seat cushion. Lift it to left seatback. Pull the handle to release adjust the seatback to your desired the folding seat latch. position.
Page 135: Adjusting The Second Row Center
Seats 3. To return the seat to the upright WARNINGS position, lift the seatback until the latch Before returning the seatback to its is fully engaged. original position, make sure that cargo or any objects are not trapped Adjusting the Second Row Center behind the seatback.
Page 136 Seats To return the seatback to its original position, lift the seatback until it latches into place. PowerFold Third Row Seat Equipped) Note: The power fold down seats operate for 10 minutes after you switch the ignition off. The transmission must be in park (P) and the liftgate, or liftgate glass must be open.
Page 137: Heated Seats
Seats Rear Seats HEATED SEATS (If Equipped) (If Equipped) WARNING Front Seats Persons who are unable to feel pain WARNING to the skin because of advanced age, chronic illness, diabetes, spinal cord People who are unable to feel pain injury, medication, alcohol use, exhaustion, to their skin because of advanced or other physical conditions, must exercise age, chronic illness, diabetes, spinal...
Page 138: Climate Controlled Seats
Seats Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. The heated seat module resets at every ignition run cycle. While the ignition is on, press the high or low heated seat switch to enable heating mode.
Page 139 Seats Locate the filters under each front seat and access them from the second-row footwell area. Move the front seats all the way forward and to the full up positions to ease access. E146319 To remove a filter: Switch the ignition off. 2.
Page 140: Universal Garage Door Opener
Universal Garage Door Opener (If Equipped) HomeLink Wireless Control System WARNINGS Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. E142657 Do not use the system with any The universal garage door opener replaces garage door opener that does not...
Page 141 Universal Garage Door Opener (If Equipped) To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming Your Garage Door Opener Motor E142658 With your vehicle parked outside of the Note: You may need a ladder to reach the garage, turn your ignition to the on unit and you may need to remove the cover...
Page 142 Universal Garage Door Opener (If Equipped) Gate Operator / Canadian Press and hold the outer two function Programming buttons simultaneously for approximately 20 seconds until the Canadian radio-frequency laws require indicator lights above the buttons flash transmitter signals to “time-out” (or quit) rapidly.
Page 143 Universal Garage Door Opener (If Equipped) Press and hold the previously programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green. 2. Press the same button twice to confirm the change.
Page 144 Universal Garage Door Opener (If Equipped) 5. Press and hold the previously programmed button on the visor for 2 seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator...
Page 145: Auxiliary Power Points
Auxiliary Power Points 12 Volt DC Power Point Locations Power points may be in the following WARNINGS locations: Do not plug optional electrical • On the lower instrument panel. accessories into the cigar lighter socket. Incorrect use of the cigar •...
Page 146 Auxiliary Power Points When the indicator light on the power point • On: The power point is working, the ignition is on and a device is plugged • Off: The power point is off, the ignition is off or no device is plugged in. •...
Page 147: Storage Compartments
Storage Compartments Press near the rear edge of the door to CENTER CONSOLE open it. Stow items in the cup holder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. Available console features include: E208344 Cup holder.
Page 148: Starting And Stopping The Engine
Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH (If Equipped) WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle or drive your vehicle on dry grass or other dry ground cover.
Page 149: Ignition Modes
Starting and Stopping the Engine Ignition Modes Note: You can crank the engine for a total of 60 seconds without the engine starting before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit.
Page 150: Starting And Stopping The Engine
Starting and Stopping the Engine Note: You must have your intelligent access 2. Insert the passive key into the backup key in your vehicle in order to shift the slot. transmission out of park (P). 3. With the key in this position, press the brake pedal then press the push button Fully depress the brake pedal.
Page 151: Automatic Engine Shutdown
Starting and Stopping the Engine Automatic Engine Shutdown 2. Switch the ignition off. 3. Apply the parking brake. For vehicles with a keyless ignition, this feature automatically shuts down the Vehicles with Keyless Start engine if it has been idling for an extended period.
Page 152: Engine Block Heater
Starting and Stopping the Engine 3. Press and hold the push button ignition Note: The heater is most effective when switch, or press it three times within outdoor temperatures are below 0°F two seconds. (-18°C). 4. Apply the parking brake. The heater acts as a starting aid by warming the engine coolant.
Page 153: Using The Engine Block Heater
Starting and Stopping the Engine • Make sure the system is unplugged and properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use. • Make sure the heater system is checked for proper operation before winter.
Page 154: Fuel And Refueling
Fuel and Refueling • Automotive fuels can be harmful or SAFETY PRECAUTIONS fatal if swallowed. Fuel such as gasoline is highly toxic and if WARNINGS swallowed can cause death or Do not overfill the fuel tank. The permanent injury. If fuel is swallowed, pressure in an overfilled tank may call a physician immediately, even if no cause leakage and lead to fuel spray...
Page 155: Fuel Quality
Fuel and Refueling • Fuels containing the octane booster FUEL QUALITY additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Choosing the Right Fuel • Leaded fuel (using leaded fuel is prohibited by law). The use of fuels with metallic compounds such as methylcyclopentadienyl manganese tricarbonyl (commonly known as MMT), which is a manganese-based fuel additive, will impair engine...
Page 156: Refueling
Fuel and Refueling Filling a Portable Fuel Container Fully open the fuel tank filler door until it engages and remove the fuel tank Use the following guidelines to avoid filler cap. electrostatic charge build-up when filling Note: Capless fuel systems do not have a an ungrounded fuel container: fuel tank filler cap.
Page 157: Fuel And Refueling
Fuel and Refueling Easy Fuel Capless Fuel System WARNINGS When refueling always shut the WARNING engine off and never allow sparks or open flames near the fuel tank filler The fuel system may be under valve. Never smoke or use a cell phone pressure.
Page 158: Fuel Consumption
Fuel and Refueling If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving.
Page 159: Emission Control System
Fuel and Refueling Calculating Fuel Economy • Fuel economy may decrease with lower temperatures. Do not measure fuel economy during the • Fuel economy may decrease when first 1,000 mi (1,600 km) of driving (this is driving short distances. your engine’s break-in period). A more •...
Page 160: Transmission
Fuel and Refueling If you use parts other than Ford, Motorcraft When the service engine soon or Ford-authorized parts for maintenance indicator illuminates, the OBD-II replacements, or for service of system has detected a components affecting emission control, malfunction. Temporary malfunctions may...
Page 161: Transmission
Fuel and Refueling Readiness for Drive on an expressway or highway for a Inspection/Maintenance (I/M) steady 15 minutes, followed by 20 minutes Testing of stop-and-go driving with at least four 30-second idle periods. Some state/provincial and local Allow the vehicle to sit for at least eight governments may have hours without starting the engine.
Page 162: Transmission
Transmission Putting your vehicle in or out of gear: AUTOMATIC TRANSMISSION Fully press down the brake pedal. WARNINGS 2. Move the gearshift lever into the Always set the parking brake fully desired gear. and latch the gearshift in park (P). 3.
Page 163 Transmission Second (2) To deactivate the tow/haul feature and return to normal driving mode, press the Transmission operates in second (2) gear button on the gearshift lever twice. The only. Use second (2) gear to start-up on TOW HAUL light will deactivate. Tow/haul slippery roads.
Page 164 Transmission In order to prevent the engine from running With the gearshift lever in drive (D), press at too low an RPM, which may cause it to the – button to active PRS. The available stall, SelectShift will still automatically and selected gears are indicated on the make some downshifts if it has determined instrument cluster.
Page 165: Brake-Shift Interlock
Transmission Brake-Shift Interlock 3. Remove the gearshift lever boot. 4. Place fingers into gearshift lever boot WARNINGS hole and pull top half of shroud up and Do not drive your vehicle until you forward to separate it from the lower verify that the brake lamps are half of the shroud.
Page 166 Transmission 8. Apply the brake, pull the white disk 3. Locate the brake shift interlock lever then move the shifter to neutral (N). on the passenger side of the shifter assembly. 9. Start your vehicle. 4. Apply the brake pedal. Using a Perform Steps 4 through 8 in reverse order, screwdriver (or similar tool), press and making sure to engage the hinge pivots...
Page 167: Four-Wheel Drive
Four-Wheel Drive (If Equipped) 4X4 HIGH USING FOUR-WHEEL DRIVE Continuously illuminates when WARNING 4H is selected. E181779 For important information regarding safe operation of this type of vehicle, 4X4 LOW see General Information in the Wheels and Tires chapter. Continuously illuminates when 4L is selected.
Page 168 Four-Wheel Drive (If Equipped) • 4H provides electronically locked four-wheel drive power to front and rear wheels. The information display will display 4H when this mode is selected. This mode is not recommended for use on dry pavement. This mode is only intended for severe winter or off-road conditions, such as deep snow, ice or shallow sand.
Page 169 Four-Wheel Drive (If Equipped) 3. Move the 4WD switch to the desired The differences that make your vehicle so mode. versatile also make it handle differently than an ordinary passenger car. The information display will display a message indicating a 4X4 shift is in Maintain steering wheel control at all progress.
Page 170 Four-Wheel Drive (If Equipped) The transfer case supples power to all four It may be less risky to strike small objects, wheels. On four-wheel drive vehicles, the such as freeway reflectors, with minor transfer case allows you to select different damage to your vehicle rather than 4WD modes when necessary.
Page 171: Rear Axle
If you must drive through high water, drive land-use regulations and responsibilities slowly. Traction or brake capability may in our nations wilderness areas. Ford Motor be limited. Company joins the U.S. Forest Service and When driving through water, determine the...
Page 172 Four-Wheel Drive (If Equipped) Note: Avoid turning on steep slopes or hills. Descend a hill in the same gear you would A danger lies in losing traction, slipping use to climb up the hill to avoid excessive sideways and possible vehicle roll over. brake application and brake overheating.
Page 173 Four-Wheel Drive (If Equipped) Avoid sudden braking. Although a four-wheel drive vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it will not stop any faster as braking occurs at all four wheels. Do not become overconfident as to road conditions.
Page 174: Rear Axle
Rear Axle LIMITED SLIP DIFFERENTIAL (If Equipped) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited-slip axle functions like a standard rear axle. The axle may exhibit a slight noise or vibration during tight turns with low vehicle speed.
Page 175: Brakes
Brakes Emergency Brake Assist GENERAL INFORMATION Emergency brake assist detects when you Note: Occasional brake noise is normal. If brake heavily by measuring the rate at a metal-to-metal, continuous grinding or which you press the brake pedal. It continuous squeal sound is present, the provides maximum braking efficiency as brake linings may be worn-out and an long as you press the pedal.
Page 176: Parking Brake
Brakes PARKING BRAKE WARNINGS You must remain in your vehicle once you have activated the system. WARNING Always set the parking brake fully During all times, you are responsible and make sure the transmission is for controlling your vehicle, placed in park (P). Failure to set the supervising the system and parking brake and engage park could result intervening, if required.
Page 177: Using Hill Start Assist
Brakes Using Hill Start Assist Bring your vehicle to a complete standstill. Keep the brake pedal pressed and select an uphill gear (for example, first (1) when facing uphill or reverse (R) when facing downhill). 2. If the sensors detect that your vehicle is on a slope, the system will activate automatically.
Page 178: Traction Control
Traction Control Switching the System Off PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time.
Page 179: Stability Control
Stability Control If a driving condition activates either the PRINCIPLE OF OPERATION stability control or the traction control system you may experience the following WARNINGS conditions: Vehicle modifications involving • The stability and traction control light braking system, aftermarket roof flashes.
Page 180: Using Stability Control
Stability Control skidding off its intended route. Vehicle with stability control maintaining control on a slippery surface. USING STABILITY CONTROL Stability Control and Traction Control with Roll Stability Control (RSC The system automatically activates when you start your engine. You can switch off the electronic stability control and roll stability control portions of the system below 35 mph (56 km/h).
Page 181: Stability Control
Stability Control Stability Control and Traction Control with RSC Features Vehicle speed Illuminated Enabled Enabled Disabled exceeds 35 mph (56 km/h) after button is pressed and held for more than 5 seconds Button pressed Not illuminated Enabled Enabled Enabled again after deactivation Button not Illuminated...
Page 182: Terrain Response
Terrain Response (If Equipped) Hill descent control requires a cooling USING HILL DESCENT down interval after sustained use. The CONTROL amount of time that the feature can remain active before cooling varies with Principle of Operation conditions. The system provides a warning in the message center and a chime sounds WARNINGS when the system is about to disengage for...
Page 183: Terrain Response
Terrain Response (If Equipped) Hill Descent Modes Information Display Message Description Hill Descent Control Active Displays at speeds below 20 mph (32 km/h) when you press the Hill Descent Control and Hill Descent Control activates. Hill Descent Control Ready Displays at speeds below 20 mph (32 km/h) when you press the Hill Descent Control switch and conditions are not correct for hill descent activation.
Page 184: Parking Aids
Parking Aids Note: The sensing system cannot be turned PRINCIPLE OF OPERATION off when a MyKey is present. See Principle of Operation (page 46). WARNINGS Note: If you attach certain add-on devices To help avoid personal injury, please such as a trailer or bike rack, the rear sensing read and understand the limitations system may detect that add-on device and of the system as contained in this...
Page 185: Front Parking Aid
Parking Aids E187330 Coverage area of up to 28 in (70 cm) from the front bumper. There is decreased E130178 coverage area at the outer corners. Coverage area of up to 6 ft (1.8 m) from The system sounds an audible warning the rear bumper.
Page 186: Rear View Camera
Parking Aids REAR VIEW CAMERA WARNINGS The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage. Objects that are close to either corner of the bumper or under the bumper, might not be seen on the E162528...
Page 187: Parking Aids
Parking Aids Note: When towing, the camera only sees Always use caution while reversing. what you are towing behind your vehicle. Objects in the red zone are closest to your This might not provide adequate coverage vehicle and objects in the green zone are as it usually provides in normal operation farther away.
Page 188 Parking Aids This allows you to get a closer view of an object behind your vehicle. The zoomed image keeps the bumper in the image to provide a reference. The zoom is only active while the transmission is in reverse (R).
Page 189: Cruise Control
Cruise Control PRINCIPLE OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). USING CRUISE CONTROL WARNINGS Do not use cruise control on winding roads, in heavy traffic or when the...
Page 190: Switching Cruise Control Off
Cruise Control Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, your vehicle returns to the speed that you previously set. • Press and release SET+ or SET-. When you select km/h as the display measurement in the Information display the set speed changes in...
Page 191: Driving Aids
Driving Aids Note: When a vehicle passes quickly BLIND SPOT INFORMATION through the blind spot zone, typically fewer SYSTEM than two seconds, the system does not trigger. WARNING Using the System To help avoid injuries, NEVER use the Blind Spot Information System as a The Blind Spot Information System turns replacement for using the interior on when you start the engine and you drive...
Page 192: Driving Aids
Driving Aids The Blind Spot Information System illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from. When the Blind Spot Information System is alerting on a vehicle and the corresponding turn signal is ON, the Blind Spot Information System alert indicator flashes as an increased warning level.
Page 193: Cross Traffic Alert
Driving Aids Switching the System Off and On If the system detects a degraded performance condition, a message warning You can temporarily switch the Blind Spot of a blocked sensor will appear in the Information System off in the information information display.
Page 194 Driving Aids Cross Traffic Alert is designed to detect fully obstructed. Reversing slowly helps vehicles that approach with a speed up to increase the coverage area and 37 mph (60 km/h). Coverage decreases effectiveness. when the sensors are partially, mostly or E142440 In this first example, the left sensor is only partially obstructed;...
Page 195: System Limitations
Driving Aids Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. System Lights, Messages and Audible Alerts E142442 The Cross Traffic Alert illuminates an amber alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from.
Page 196: False Alerts
Driving Aids The following are other situations that may Note: The Cross Traffic Alert switches on limit the Cross Traffic Alert performance: whenever the ignition is switched on and ready to provide appropriate alerts when • Adjacently parked vehicles or objects the transmission is in reverse (R).
Page 197: Drive Control
Driving Aids Extreme continuous steering may increase DRIVE CONTROL the effort required for you to steer your vehicle. This increased effort prevents Driver Select Suspension overheating and permanent damage to the steering system. You do not lose the Driver select suspension delivers a unique ability to steer your vehicle manually.
Page 198: Self-Leveling Suspension
Driving Aids Modes: SELF-LEVELING SUSPENSION • Comfort – Provides a more relaxed The self-leveling suspension system is driving experience, maximizing comfort. designed to improve ride, handling and Your steering effort decreases and the general vehicle performance during: suspension movement is more fluid. Comfort mode is ideal when you desire •...
Page 199: Load Carrying
Load Carrying To move the shelf to the shelf position: REAR UNDER FLOOR STORAGE (If Equipped) Cargo Management System E205356 Pull up and pivot the shelf over the channels on the side trim panels and snap the shelf ends in the channels. E205355 To move the shelf to the divider A storage compartment is located in the...
Page 200: Roof Racks And Load Carriers
When using the roof rack system, we recommend you use Ford Genuine Accessory crossbars designed specifically for your vehicle. Make sure that you securely fasten the load. Check the tightness of the load before driving and at each fuel stop.
Page 201: Load Limit
Load Carrying the following terms for LOAD LIMIT determining your vehicle’s weight Vehicle Loading - with and ratings, with or without a trailer, without a Trailer from the vehicle’s Tire Label or Safety Compliance Certification This section will guide you in the Label: proper loading of your vehicle, Base Curb Weight - is the weight...
Page 202: Load Carrying
Load Carrying Example only: WARNING The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space E210944...
Page 203: Towing
Load Carrying Cargo Weight - includes all Certification Label. The label shall weight added to the Base Curb be affixed to either the door hinge Weight, including cargo and pillar, door-latch post, or the door optional equipment. When towing, edge that meets the door-latch trailer tongue load or king pin post, next to the driver seating weight is also part of cargo weight.
Page 204 Load Carrying Example only: E198828 WARNING Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. E143819 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 205: Towing
Load Carrying GCW (Gross Combined Weight) Tongue Load or Fifth Wheel - is the Gross Vehicle Weight plus King Pin Weight - refers to the the weight of the fully loaded amount of the weight that a trailer trailer. pushes down on a trailer hitch. GCWR (Gross Combined Examples: For a 5000 pound Weight Rating) - is the maximum...
Page 206: Towing
Load Carrying 1. Locate the statement "The *Suppose your vehicle has a combined weight of occupants 1400-pound (635-kilogram) cargo and cargo should never exceed and luggage capacity. You decide XXX kg or XXX lb." on your to go golfing. Is there enough load vehicle’s placard.
Page 207 Load Carrying be: 635 kilograms - (2 x 99 Special Loading Instructions kilograms) - (12 x 45 kilograms) = for Owners of Pick-up Trucks 635 - 198 - 540 = -103 kilograms. and Utility-type Vehicles You will need to reduce the load WARNING weight by at least 240 pounds (104 kilograms).
Page 208: Towing
Towing Load Placement TOWING A TRAILER To help minimize how trailer WARNINGS movement affects your vehicle Do not exceed the GVWR or when driving: the GAWR specified on the • Load the heaviest items closest certification label. to the trailer floor. Towing trailers beyond the •...
Page 209: Trailer Sway Control
Ford Note: Make sure to take into consideration does not recommend disabling this feature trailer frontal area. Do not exceed 36.5 feet²...
Page 210 Towing To calculate the maximum loaded trailer 3. This equals the maximum loaded weight for your vehicle: trailer weight for this combination. Start with the gross combined weight Note: The trailer tongue load figures into rating for your vehicle model and axle the payload for your vehicle.
Page 211: Essential Towing Checks
Towing When attaching the trailer wiring connector ESSENTIAL TOWING CHECKS to your vehicle, only use a proper fitting connector that works with the vehicle and Follow these guidelines for safe towing: trailer functions. Some seven-position • Do not tow a trailer until you drive your connectors may have the SAE J2863 logo, vehicle at least 1000 miles (1600 which confirms that it is the proper wiring...
Page 212 Towing Integrated Hitch Rating The standard integrated hitch has two ratings depending on mode of operation: WARNING • Weight-carrying mode requires a draw Towing trailers beyond the maximum bar and hitch ball. The draw bar tongue weight exceeds the limit of supports all the vertical tongue load of the towing system and could result the trailer.
Page 213: Safety Chains
Towing Weight-distributing Hitch - Vehicles 8. Drive the vehicle and trailer at 20–25 with Automatic Leveling Suspension mph (32–40 km/h) for approximately 2 miles (3 kilometers) to re-level the WARNING suspension. Do not adjust a weight-distributing 9. Park your vehicle and trailer on a level hitch to any position where the rear surface.
Page 214: Trailer Brakes
Integrated Trailer Brake Controller (If braking). The gain setting displays in the Equipped) message center. WARNING The Ford trailer brake controller has been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and most electric-over-hydraulic brakes. It will not activate hydraulic surge-style trailer brakes.
Page 215 Towing The controller shows gain setting, output B: Manual control lever: Slide the control bar graph, and trailer connectivity status lever to the left to turn on the trailer's in the information display. They appear in electric brakes independent of the tow the information display as follows: vehicle's.
Page 216 However, your Ford warranty does not cover • Avoid towing in adverse weather this diagnosis if the fault is with the trailer.
Page 217: When Towing A Trailer
The trailer brake controller is only a gearshift in position P to aid engine and factory-installed or dealer-installed transmission cooling and to help A/C item. Ford is not responsible for performance. warranty or performance of the • Turn off the speed control with heavy controller due to misuse or customer loads or in hilly terrain.
Page 218: Towing Points
Towing • Allow more distance for stopping with Exceeding these limits may allow water to a trailer attached. Anticipate stops and enter vehicle components: brake gradually. • Causing internal damage to the • Avoid parking on a grade. However, if components.
Page 219: Transporting The Vehicle
We recommend the use of a wheel lift and dollies or flatbed equipment to tow your vehicle. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Vehicle damage may occur if towed incorrectly, or by any other means.
Page 220: Towing The Vehicle On Four Wheels
Towing It is acceptable to have your two-wheel Follow these guidelines if you have a need drive vehicle towed with the front wheels for recreational towing, for example towing on the ground (without dollies) and the your vehicle behind a motorhome. These rear wheels off the ground.
Page 221 Towing Note: If completed successfully, the WARNINGS information display shows NEUTRAL TOW Failing to put the transfer case in its LEAVE IN N or NEUTRAL TOW ENABLED neutral position will damage vehicle LEAVE TRANSMISSION IN NEUTRAL. components. This indicates that your vehicle is safe to tow with all wheels on the ground.
Page 222 Towing 6. Release the parking brake, start the engine, and shift the transmission to position D to make sure the transfer case is out of position N. If the transfer case does not successfully shift out of position N, set the parking brake until you can have your vehicle serviced.
Page 223: Driving Hints
Driving Hints 4. Check the coolant level. See Engine BREAKING-IN Coolant Check (page 247). You need to break in new tires for 5. Have your vehicle checked by an approximately 300 miles (480 authorized dealer as soon as possible. kilometers). During this time, your vehicle may exhibit some unusual driving ECONOMICAL DRIVING characteristics.
Page 224: Driving Through Water
Driving Hints • Avoid using speed control in hilly When driving through standing water, drive terrain. very slowly and do not stop your vehicle. Your brake performance and traction may • Do not rest your foot on the brake be limited. After driving through water and pedal while driving.
Page 225: Driving Hints
Driving Hints WARNINGS Never place floor mats or any other covering on top of already installed floor mats. Floor mats should always rest on top of vehicle carpeting surface and not another floor mat or other covering. Additional floor mats or any other covering will reduce the pedal clearance and potentially interfere with pedal operation.
Page 226: Roadside Emergencies
• Towing — independent service contractors, if not prohibited by state, Canadian customers who require roadside local or municipal law, shall tow Ford assistance, call 1-800-665-2006. eligible vehicles to an authorized dealer within 35 mi (56 km) of the Vehicles Sold in Canada: Using...
Page 227: Hazard Warning Flashers
Well maintained roads and increase the risk of fire and serious surfaces help ensure safe travel for the injury. Ford Motor Company recommends supplier, and allow their representatives that the fuel system be inspected by an to perform service as per the standard authorized dealer after any collision.
Page 228: Preparing Your Vehicle
Roadside Emergencies Preparing Your Vehicle 3. Remove your foot from the brake pedal and press the START/STOP button Do not attempt to push-start your to switch off the ignition. automatic transmission vehicle. 4. You can either attempt to start the Note: Attempting to push-start a vehicle engine by pressing the brake pedal and with an automatic transmission may cause...
Page 229: Jump Starting
Roadside Emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the booster vehicle battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery and the fuel injection system, or connect the negative (-) cable to a ground connection point if available.
Page 230: Roadside Emergencies
Roadside Emergencies E142665 Remove the negative (-) jumper cable from the disabled vehicle. 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle battery.
Page 231: Customer Assistance
A reasonable time must be allowed to Oakville, Ontario L6K 0C8 perform a repair after taking your vehicle Telephone to the authorized dealer. Repairs will be made using Ford or Motorcraft® parts, or 1-800-565-3673 (FORD) remanufactured or other parts that are Online authorized by Ford.
Page 232: In California (U.s. Only)
2. Four or more repair attempts are made Ford in writing before pursuing remedies on the same nonconformity (a defect under your state’s warranty laws. Ford is or condition that substantially impairs also allowed a final repair attempt in some the use, value or safety of the vehicle) states.
Page 233: The Better Business Bureau (Bbb) Auto Line Program (U.s. Only)
BBB. Canadian dealers. In those cases where You are not bound by the decision, and you continue to feel that the efforts by Ford may reject the decision and proceed to of Canada and the authorized dealer to...
Page 234: Getting Assistance Outside The U.s. And Canada
CAMVAP decisions are fast, fair, FORD MOTOR COMPANY and final as the arbitrator’s award is Customer Relationship Center binding on both you and Ford of Canada. 1555 Fairlane Drive CAMVAP services are available in all Fairlane Business Park #3 Canadian territories and provinces.
Page 235: Ordering Additional Owner's Literature
(VIN) and new REPORTING SAFETY DEFECTS address with Ford Motor Company Export (U.S. ONLY) Operations & Global Growth Initiatives by emailing expcac@ford.com. If you are in another foreign country, contact the nearest authorized dealer.
Page 236: Reporting Safety Defects (Canada Only)
However, information about motor vehicle NHTSA cannot become involved safety from in individual problems between http://www.safercar.gov. you, your dealer, or Ford Motor Company. REPORTING SAFETY DEFECTS To contact NHTSA, you may call (CANADA ONLY) the Vehicle Safety Hotline...
Page 237: Fuses
Fuses The power distribution box is located in FUSE SPECIFICATION CHART the engine compartment. It has high-current fuses that protect your Power Distribution Box vehicle’s main electrical systems from overloads. WARNINGS Always disconnect the battery before If you disconnect and reconnect the servicing high current fuses.
Page 238 Fuses Fuse or relay number Fuse amp rating Protected components Relay Electronic cooling fan. Relay Rear window defroster. Heated mirror relay. Relay Electronic cooling fan. Relay Run/start relay. Relay Power distribution box relay. 40A* Power running boards. Heated seats. 40A* Run/start relay.
Page 239 Fuses Fuse or relay number Fuse amp rating Protected components 40A* Blower motor relay. 40A* 110-volt AC power point. 30A* Auxiliary blower motor. 50A* Powertrain control module relay. 30A* Power liftgate. — Not used. — Not used. Relay Trailer tow backup lamps relay. Relay Electronic fan 2 relay.
Page 240 Fuses Fuse or relay number Fuse amp rating Protected components 5A** Blower motor run/start. — Not used. 15A** Heated mirrors. — Not used. — Not used. — Not used. 25A* Electronic fan. 30A* Moonroof. — Not used. 20A* Auxiliary power point (rear of center console).
Page 241: Passenger Compartment Fuse Panel
Fuses Fuse or relay number Fuse amp rating Protected components — Not used. 5A** Rain sensor. — Not used. — Not used. Relay Wiper motor relay. *Cartridge fuses. **Mini fuses. To remove the trim panel for access to the Passenger Compartment Fuse fuse box, pull the panel toward you and Panel swing it out away from the side and...
Page 242 Fuses E163102 The fuses are coded as follows: Fuse or relay number Fuse amp rating Protected components Driver window. Rear seat control. Multimedia gateway module. Passenger window. Demand lamps. Amplifier. Rear electronic automatic temperature control. 7.5A Power mirror. I n f o r ma t i o n P r o v i d e d b y : Driver seat memory switch.
Page 243 Fuses Fuse or relay number Fuse amp rating Protected components SYNC. Power lift gate. Electric finish panel. Display. Run accessory relay. Passive entry/start module. Interior lighting. Puddle lamps. Right turn and stop/turn signals. Left turn and stop/turn signals. Reverse lamp. Center high mount stop lamp.
Page 244 Fuses Fuse or relay number Fuse amp rating Protected components Ignition switch. Key inhibit switch. Radio. GPS. Front park lamps. Trailer brake on/off. Power vent. Rear windows. Power inverter. CCD suspension module. Rear park assist. Rear camera. BLIS. Heated seat. Climate module.
Page 245: Changing A Fuse
Fuses Fuse or relay number Fuse amp rating Protected components Fog lamps. — Not used. — Not used. CHANGING A FUSE Fuses WARNING You must replace a failed fuse with one that has the specified amperage rating. If you use a fuse with a higher amperage rating, you may cause severe wire damage and may start a fire.
Page 246: Maintenance
Maintenance Working with the Engine On GENERAL INFORMATION WARNING Have your vehicle serviced regularly to help maintain its roadworthiness and resale To reduce the risk of vehicle damage value. There is a large network of and/or personal burn injuries, do not authorized dealers that are there to help start your engine with the air cleaner you with their professional servicing...
Page 247: Under Hood Overview - 3.5L Ecoboost
Maintenance 3. Raise the hood until the lift cylinders hold it open. 4. To close, lower the hood and make sure that it is closed properly and fully latched. E190266 UNDER HOOD OVERVIEW - 3.5L ECOBOOST E166496 Windshield washer fluid reservoir. See Washer Fluid Check (page 252). I n f o r ma t i o n P r o v i d e d b y : Battery.
Page 248: Engine Oil Dipstick
Maintenance Engine oil filler cap. See Engine Oil Check (page 245). Engine oil dipstick. See Engine Oil Dipstick (page 245). Brake fluid reservoir. See Brake Fluid Check (page 251). Engine coolant reservoir. See Engine Coolant Check (page 247). Air filter assembly. See Changing the Engine Air Filter (page 262). Power distribution box.
Page 249: Oil Change Indicator Reset
2. If the engine oil level is not within the following message. normal range, add engine oil that Reset Successful meets Ford specifications. See Capacities and Specifications (page When the oil change indic- 303). ator resets the instrument 3.
Page 250: Engine Coolant Check
Maintenance Note: For best results, coolant ENGINE COOLANT CHECK concentration should be tested with a refractometer such as Robinair® Coolant WARNINGS and Battery Refractometer 75240. We do Do not add engine coolant when the not recommend the use of hydrometers or engine is hot.
Page 251: Severe Climates
Maintenance Severe Climates 3. Refill with engine coolant as soon as possible. If you drive in extremely cold climates: Water alone, without engine coolant, can • It may be necessary to have an cause engine damage from corrosion, authorized dealer increase the coolant overheating or freezing.
Page 252 Maintenance the service engine soon indicator You have limited engine power when in the will illuminate. fail-safe mode, so drive your vehicle with caution. Your vehicle will not maintain If the engine reaches a preset high-speed operation and the engine will over-temperature condition, the engine operate poorly.
Page 253: Automatic Transmission Fluid Check
Maintenance At this time, you may notice your engine 5. If the coolant is low, add coolant, and coolant temperature gauge needle move restart the engine. See Adding Engine toward the H and the POWER REDUCED Coolant or How Fail-Safe Cooling TO LOWER TEMP message may appear Works in this chapter for more in the information display.
Page 254: Transfer Case Fluid Check
4. Add fluid through the filler opening. Fill to the bottom of the opening. Use only fluid that meets Ford specifications. See Capacities and Specifications (page 303). I n f o r ma t i o n P r o v i d e d b y :...
Page 255: Washer Fluid Check
Batteries normally produce explosive unless you are adding fluid. gases which can cause personal Only use fluid that meets Ford injury. Therefore, do not allow specifications. See Capacities and flames, sparks or lighted substances to Specifications (page 303).
Page 256 Maintenance If you see any corrosion on the battery or WARNINGS terminals, remove the cables from the Keep batteries out of reach of terminals and clean with a wire brush. You children. Batteries contain sulfuric can neutralize the acid with a solution of acid.
Page 257: Checking The Wiper Blades
Maintenance Note: For flexible fuel vehicles, if you are After battery replacement, or in some operating on E85, you may experience poor cases after charging the battery with an starts or an inability to start the engine and external charger, the battery management driveability problems until the fuel trim and system requires eight hours of vehicle sleep ethanol content have been relearned.
Page 258: Changing The Wiper Blades
Maintenance 3. Press the wiper blade secondary CHANGING THE WIPER locking clip. BLADES 4. Remove the wiper blade. Note: Do not hold the wiper blade when Note: Make sure that the wiper arm does lifting the wiper arm. not spring back against the glass when the wiper blade is not attached.
Page 259: Removing A Headlamp
Maintenance Vertical Aim Adjustment Park your vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. 2. Measure the height from the center of your headlamp (indicated by a 3.0 millimeter circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of...
Page 260: Changing A Bulb
Maintenance Note: If the bulb is accidentally touched, clean it with rubbing alcohol before installing it. Headlamp Bulb Switch all of the lamps and the ignition off. 2. Remove the headlamp. See Removing a Headlamp (page 256). E167360 3. Remove the pushpin at the upper inboard corner of the lamp.
Page 261: Front Direction Indicator Bulb
Maintenance Front Direction Indicator Bulb LED Direction Indicator and Side Marker Bulbs (If Equipped) These lamps have LED bulbs. Contact an authorized dealer. Fog Lamp Bulb (If Equipped) E205569 Switch all of the lamps and the ignition off. 2. Remove the headlamp. See Removing a Headlamp (page 256).
Page 262 Maintenance Rear Lamp, Brake Lamp, Rear LED Rear Lamp, Brake Lamp, Rear Direction Indicator and Reverse Direction Indicator and Reverse Lamp Bulbs Lamp Bulbs (If Equipped) These lamps have LED bulbs. Contact an authorized dealer. Central High-mounted Brake Lamp Bulb Switch all of the lamps and the ignition off.
Page 263: Bulb Specification Chart
Maintenance License Plate Lamp Bulb 3. Remove the bulb by pulling it straight out. Side Direction Indicator Bulb These lamps have LED bulbs. Contact an authorized dealer. BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized D.O.T.
Page 264 Maintenance Interior Lamps Lamp Specification Power (Watt) Glove compartment lamp. Vanity mirror lamp. A6224PF Map lamp. Interior lamp. Rear dome lamp. Second row rail lamp. I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 265: Changing The Engine Air Filter
Maintenance CHANGING THE ENGINE AIR FILTER WARNING To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. Note: Failure to use the correct air filter E163756 element may result in severe engine 2.
Page 266 Maintenance E163758 E163760 5. Release the three clamps that secure Reconnect the mass air flow sensor the cover to the air filter housing. Push electrical connector to the outlet the air filter cover toward the center of tube. Make sure the locking tab on the vehicle and up slightly to release it.
Page 267: Vehicle Care
Vehicle Care GENERAL INFORMATION CLEANING THE EXTERIOR Your Ford or Lincoln authorized dealer has Wash your vehicle regularly with cool or many quality products available to clean lukewarm water and a neutral pH your vehicle and protect its finishes. shampoo, we recommend Motorcraft Detail Wash.
Page 268: Waxing
Vehicle Care Note: Never use abrasive materials, for • Do not allow wax to come in contact example steel wool or plastic pads as they with any non-body (low-gloss black) can scratch the chrome surface. colored trim. The wax will discolor or stain the parts over time.
Page 269: Cleaning The Windows And Wiper Blades
Vehicle Care • Never wash or rinse any ignition coil, CLEANING THE INTERIOR spark plug wire or spark plug well, or the area in and around these locations. WARNINGS • Cover the battery, power distribution Do not use cleaning solvents, bleach box, and air filter assembly to prevent or dye on the vehicle’s safety belts, water damage when cleaning the...
Page 270: Cleaning The Instrument Panel And Instrument Cluster Lens
Vehicle Care Wipe up spilled liquid using a clean, CLEANING THE INSTRUMENT soft cloth as quickly as possible. PANEL AND INSTRUMENT 2. Use Motorcraft Premium Leather and CLUSTER LENS Vinyl Cleaner or a commercially available leather cleaning product for WARNING automotive interiors.
Page 271: Vehicle Care
Vehicle Care You should: • Do not spill coffee, ketchup, mustard, orange juice or oil-based products on • Remove dust and loose dirt with a the leather as they may permanently vacuum cleaner. stain the leather. • Clean and treat spills and stains as •...
Page 272: Repairing Minor Paint Damage
Vehicle Care • Clean the wheels weekly using REPAIRING MINOR PAINT Motorcraft Wheel and Tire Cleaner. DAMAGE Apply using manufacturer's instructions. Authorized dealers have touch-up paint to • Use a sponge to remove heavy match your vehicle’s color. Your vehicle deposits of dirt and brake dust color code is printed on a sticker on the accumulation.
Page 273: Removing Vehicle From Storage
Vehicle Care Battery • Touch-up exposed or primed metal to prevent rust. • Check and recharge as necessary. Keep • Cover chrome and stainless steel parts connections clean. with a thick coat of auto wax to prevent • If storing your vehicle for more than 30 discoloration.
Page 274 Vehicle Care • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive your vehicle 15 ft (4.5 m) back and forth to remove rust build-up. • Check fluid levels (including coolant, oil and gas) to make sure there are no leaks, and fluids are at recommended levels.
Page 275: Wheels And Tires
Ford dealer to have the system abrupt maneuvers, drive at safe speeds for reprogrammed. If you intend to change the the conditions, keep tires inflated to Ford size of the wheels from that fitted by the recommended pressures, never overload...
Page 276: Wheels And Tires
Wheels and Tires Utility vehicles and trucks handle On some four-wheel drive vehicles, the differently than passenger cars in the initial shift from two-wheel to four-wheel various driving conditions that are drive while the vehicle is moving can cause encountered on streets, highways and a momentary clunk and ratcheting sound.
Page 277 Wheels and Tires E168583 E145299 • Higher - to allow higher load carrying As a result of the above dimensional capacity and to allow it to travel over differences, Sport utility vehicles and rough terrain without getting hung up trucks often will have a higher center of or damaging underbody components.
Page 278: Tire Care
U.S. Department of TIRE CARE Transportation Tire quality Information About Uniform grades: The U.S. Department of Tire Quality Grading Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 279 Wheels and Tires The traction grades, from highest Federal Motor Vehicle Safety to lowest are AA, A, B, and C. The Standard No. 139. Grades B and A grades represent the tire’s ability represent higher levels of to stop on wet pavement as performance on the laboratory measured under controlled test wheel than the minimum...
Page 280 Wheels and Tires *kPa: Kilopascal, a metric unit of Information Contained on the air pressure. Tire Sidewall *PSI: Pounds per square inch, a Both United States and Canada standard unit of air pressure. Federal regulations require tire manufacturers to place *Cold tire pressure: The tire standardized information on the pressure when the vehicle has...
Page 281 Wheels and Tires A. P: Indicates a tire, designated G. H: Indicates the tire's speed by the Tire and Rim Association, rating. The speed rating denotes that may be used for service on the speed at which a tire is cars, sport utility vehicles, designed to be driven for extended minivans and light trucks.
Page 282 Wheels and Tires J. Tire Ply Composition and Letter mph ( km/h) Material Used: Indicates the rating number of plies or the number of 168 (270) layers of rubber-coated fabric in the tire tread and sidewall. Tire 186 (299) manufacturers also must indicate Note: For tires with a maximum the ply materials in the tire and the sidewall, which include steel,...
Page 283 Wheels and Tires *Traction: The traction grades, The tire suppliers may have from highest to lowest are AA, A, additional markings, notes or B, and C. The grades represent the warnings such as standard load tire's ability to stop on wet or radial tubeless.
Page 284 Wheels and Tires C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual; defined as four tires on the rear axle (a total of six or more tires on the vehicle).
Page 285 Numbers of 70 or automatic service station gauges lower indicate a short sidewall. may be inaccurate. Ford recommends the use of a digital D. D: Indicates a diagonal type tire. or dial-type tire pressure gauge R: Indicates a radial type tire.
Page 286 Certification Label or Tire Label. of the vehicle. If you do not maintain the inflation pressure at When weather temperature the levels specified by Ford, your changes occur, tire inflation vehicle may experience a condition pressures also change. A 10°F known as shimmy.
Page 287 Wheels and Tires Note: If you are checking tire Note: Some spare tires operate at pressure when the tire is hot, (for a higher inflation pressure than the example, driven more than 1 mile other tires. For T type mini-spare [1.6 kilometers]), never bleed or tires, see the Dissimilar spare wheel reduce air pressure.
Page 288 Wheels and Tires it needs to be repaired or replaced. When the tire tread wears down For your safety, tires that are to the same height as these wear damaged or show signs of bars, the tire is worn out and must excessive wear should not be used be replaced.
Page 289 LT-metric or all-season versus sidewall of all tires. This all-terrain) as those originally information identifies and provided by Ford. The describes the fundamental recommended tire and wheel size characteristics of the tire and also may be found on either the Safety provides a U.S.
Page 290 Wheels and Tires WARNINGS WARNINGS not recommended by Ford can 3. Stand at a minimum of 12 ft affect the safety and performance (3.6 m) away from the wheel and of your vehicle, which could result tire assembly. in an increased risk of loss of vehicle control, vehicle rollover, 4.
Page 291 Wheels and Tires If the tire pressure monitoring Highway Hazards system indicator is flashing, the No matter how carefully you drive system is malfunctioning. Your there’s always the possibility that replacement tire might be you may eventually have a flat tire incompatible with your tire on the highway.
Page 292 Wheels and Tires Wheel misalignment in the front Note: Your vehicle may be or the rear can cause uneven and equipped with a dissimilar spare rapid treadwear of your tires and wheel and tire assembly. A should be corrected by an dissimilar spare wheel and tire authorized dealer.
Page 293: Using Snow Chains
Snow tires must be the same size, load index, speed rating as those • Install chains securely, verifying that originally provided by Ford. Use of the chains do not touch any wiring, any tire or wheel not recommended by brake lines, or fuel lines.
Page 294 Wheels and Tires Each tire, including the spare (if When the malfunction indicator is provided), should be checked illuminated, the system may not be able monthly when cold and inflated to detect or signal low tire pressure as to the inflation pressure recommended by intended.
Page 295 Wheels and Tires Changing Tires With a Tire Understanding Your Tire Pressure Pressure Monitoring System Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low.
Page 296 Wheels and Tires Low tire pressure Possible cause Customer action required warning light Solid warning light Tire(s) under-inflated Make sure tires are at the proper pres- sure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar),...
Page 297 Wheels and Tires When Inflating Your Tires Tire Pressure Monitoring System Reset Procedure When putting air into your tires (such as at a gas station or in your garage), the tire WARNING pressure monitoring system may not To determine the required respond immediately to the air added to pressure(s) for your vehicle, see the your tires.
Page 298 (one meter) away from another starting with the left front tire in the Ford Motor Company vehicle following clockwise order: Left front undergoing the system reset procedure (driver's side front tire), Right front at the same time.
Page 299: Changing A Road Wheel
If the tire pressure monitor sensor and wheels that were originally provided becomes damaged, it will no longer by Ford. If the dissimilar spare tire or wheel function. See Tire Pressure is damaged, it should be replaced rather Monitoring System (page 290).
Page 300: Location Of The Spare Tire And Tools
Wheels and Tires When driving with one of the dissimilar • Use commercial car washing spare tires listed above, do not: equipment. • Exceed 50 mph (80 km/h). • Use snow chains on the end of the vehicle with the dissimilar spare wheel •...
Page 301: Tire Change Procedure
Always use the jack provided as versus all-terrain) as those originally original equipment with your vehicle. provided by Ford. The recommended tire If using a jack other than the one and wheel size may be found on either the provided as original equipment with your...
Page 302 Wheels and Tires Park on a level surface, activate the hazard 3. Insert the winch extension tool flashers and set the parking brake. Then, assembly through the access hole in place the transmission in park (P) and turn the floor and engage the winch. the engine off.
Page 303 Wheels and Tires 6. Raise the vehicle to provide sufficient ground clearance when installing the spare tire, about 1/4 inch (6 millimeters). Installing the Spare Tire E208657 Rear jacking point E175447 Remove the lug nuts with the lug wrench. 2. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Page 304: Technical Specifications
M14 x 1.5 150 lb.ft (204 Nm) Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. I n f o r ma t i o n P r o v i d e d b y : Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).
Page 305 Wheels and Tires E145950 Wheel pilot bore Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles. I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 306: Capacities And Specifications
Capacities and Specifications ENGINE SPECIFICATIONS Engine 3.5L Ecoboost Cubic inches Firing order 1-4-2-5-3-6 Ignition system Coil on plug Compression ratio 10.0:1 Spark plug gap 0.030 in (0.75 mm) - 0.033 in (0.85 mm) Drivebelt Routing E167467 MOTORCRAFT PARTS Component Part Number Air filter element FA-1883 Oil filter...
Page 307: Capacities And Specifications
Rear window wiper blade WW-1612 We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability.
Page 308: Vehicle Identification Number
Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. E142477 World manufacturer identifier Brake system, Gross Vehicle Weight Rating, Restraint Devices and their locations Make, vehicle line, series, body type Engine type Check digit...
Page 309: Vehicle Certification Label
Capacities and Specifications VEHICLE CERTIFICATION TRANSMISSION CODE LABEL DESIGNATION E167469 E167814 The National Highway Traffic Safety The transmission code is on the Safety Administration Regulations require that a Compliance Certification Label. The Safety Compliance Certification Label be following table shows the transmission affixed to a vehicle and prescribe where code along with the transmission the Safety Compliance Certification Label...
Page 310: Capacities And Specifications - 3.5L Ecoboost
Capacities and Specifications CAPACITIES AND SPECIFICATIONS - 3.5L ECOBOOST Capacities WARNING The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel. Item Capacity Engine oil...
Page 311 Do not check or change the lubricant unless you suspect a leak or submerge the axle in water. Contact an authorized dealer. Add 4 oz. (118 ml) of Additive Friction Modifier XL-3 or equivalent for complete refill of Ford limited-slip differential. Approximate dry fill capacity. Actual amount may vary during fluid changes. Specifications...
Page 312 Capacities and Specifications Name Specification Brake fluid (U.S. and Mexico): WSS-M6C65-A1 Motorcraft DOT 3 Motor Vehicle Brake Fluid PM-1-C Brake fluid (Canada): WSS-M6C65-A1 High Performance DOT 3 Motor Vehicle Brake Fluid CPM-1-C Brake fluid: WSS-M6C65-A2 Motorcraft® DOT 4 LV High Performance Motor Vehicle Brake Fluid (U.S.
Page 313 Capacities and Specifications Name Specification A/C refrigerant (Canada): WSH-M17B19-A Motorcraft R-134a Refrigerant CYN-16-R A/C refrigerant (Mexico): WSH-M17B19-A Motorcraft R-134a Refrigerant MYN-19 A/C refrigerant compressor oil: WSH-M1C231-B Motorcraft PAG Refrigerant Compressor Oil YN-12-D Multi-purpose grease: ESB-M1C93-B Motorcraft Multi-Purpose Grease Spray XL-5 Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1...
Page 314 Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.
Page 315: Audio System
Audio systems capable of recognizing and compact discs may not function correctly playing MP3 and WMA individual tracks when used in Ford CD players. and folder structures work as follows: • There are two different modes for MP3...
Page 316: Audio Unit - Vehicles With: Am/Fm/Cd/Sync/Satellite Radio
Audio System • MP3 and WMA folder mode represents AUDIO UNIT - VEHICLES WITH: a folder structure consisting of one AM/FM/CD/SYNC/SATELLITE level of folders. The CD player numbers RADIO all MP3 and WMA tracks on the disc (noted by the MP3 or WMA file extension) and all folders containing WARNING MP3 and WMA files, from F001 (folder)
Page 317: Audio System
Audio System E205855 Display screen: Shows audio and SYNC information. Number block: In radio mode, store your favorite stations for later access. When tuned to any station, press and hold a preset button until sound returns. In CD mode, press a button to select a track. In phone mode, press the buttons to enter a phone number.
Page 318: Audio Unit - Vehicles With: Sony Am/Fm/Cd
Audio System Power and volume: Press this button to switch the system off and on. Turn the control to adjust the volume. CD slot: Insert a CD. Eject: Press this button to eject a CD. SOUND: Press this button to adjust settings for Treble, Midrange, Bass, Balance and Fade.
Page 319 Audio System E205856 TUNE: Turn this control to search through the radio frequency band manually. Memory presets: Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns. MEDIA: Press this button to access different audio modes, such as AM, FM and A/V Input.
Page 320: Digital Radio
Audio System Rear Seat Audio Controls E182082 VOL: Adjust radio volume. MEDIA: Scroll through available audio system modes. Rear audio display: See displayed time, radio frequency, Sirius radio channel or CD track. CLOCK: Press to display the current time in 12-hour format. The time displays for a few seconds or you can press the CLOCK button again to switch immediately back to the last media state.
Page 321 Audio System When HD Radio broadcasts are active, you • Memory presets allow you to save an can access the following functions: active channel as a memory preset. Touch and hold a memory preset slot • Scan allows you to hear a brief until the sound returns.
Page 322: Satellite Radio
SIRIUS® broadcasts a variety of music, HD Radio logos are proprietary trademarks news, sports, weather, traffic and of iBiquity Digital Corp. Ford Motor entertainment satellite radio channels. For Company and iBiquity Digital Corp. are not more information and a complete list of...
Page 323: Satellite Radio Reception Factors
Ford Motor Company shall not be of your vehicle. See an authorized dealer responsible for any such programming for availability.
Page 324 Audio System Troubleshooting Message Condition Action Acquiring… Radio requires more than No action required. This two seconds to produce message should disappear audio for the selected shortly. channel. Satellite antenna fault There is an internal module If this message does not or system failure present.
Page 325: Usb Port
Audio System USB PORT (If Equipped) E207805 See your SYNC information. E205592 WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Page 326: Sync
SYNC (If Equipped) GENERAL INFORMATION E198355 • Text message. SYNC is an in-vehicle communications system that works with your • Use the advanced voice recognition Bluetooth-enabled cellular phone and system. portable media player. This allows you to: • Charge your USB device (if your device •...
Page 327 SYNC (If Equipped) Monday-Saturday, 8:30am-9:00pm EST. When using SYNC: • Do not operate playing devices if the Sunday, 10:30am-7:30pm EST. power cords or cables are broken, split In the United States, call 1-800-392-3673. or damaged. Place cords and cables In Canada, call 1-800-565-3673. out of the way, so they do not interfere with the operation of pedals, seats, Times are subject to change due to...
Page 328: Using Voice Recognition
Make sure the interior of your vehicle is vehicle's SYNC module. Ford Motor as quiet as possible. Wind noise from Company and Ford of Canada will not open windows and road vibrations may access the system data for any purpose...
Page 329: System Interaction And Feedback
SYNC (If Equipped) Voice command If you want the system to carry out the following Voice Settings | Voice Adjust the level of voice interaction and feedback. Preferences Help Hear a list of voice commands available in the current mode. You can say any of the voice commands that appear within open and close brackets that are separated by |.
Page 330 SYNC (If Equipped) Confirmation prompts are short questions correct?". If turned off, the system simply the system asks when it is not sure of your makes a best guess as to what you request or when there are multiple possible requested and may ask you to confirm responses to your request.
Page 331: Using Sync With Your Phone
SYNC (If Equipped) Other features, such as text messaging USING SYNC WITH YOUR using Bluetooth and automatic phonebook PHONE download, are cell phone-dependent features. To check your cell phone's Hands-free calling is one of the main compatibility, see your cell phone's manual features of SYNC.
Page 332: Pairing Subsequent Cell Phones
SYNC (If Equipped) Pairing Subsequent Cell Phones Depending on your cell phone's capability and your market, the system may prompt Note: To scroll through the menus, press you with questions, such as setting the the up and down arrows on your audio current cell phone as the primary cell system.
Page 333 SYNC (If Equipped) Voice Command You can also say any of the following: [Phone] Settings [Message] Notification Voice Command Call ___ [Phone] Settings [Message] Notification Call ___ at Home [Phone] Settings [Set] Phone Ringer Call ___ at Work [Phone] Settings [Set] Ringer 1 Call ___ in Office [Phone] Settings [Set] Ringer 2 Call ___ on Mobile...
Page 334: Making A Call
SYNC (If Equipped) Making a Call Press the voice button and when prompted say: Voice Command Action and Description Call ___ This command is not available until your cell phone informa- tion is completely downloaded using Bluetooth. Dial Use to enter a phone number digit by digit. When the system confirms the number say one of the following commands: Dial To confirm the number and initiate the call.
Page 335 SYNC (If Equipped) Message Action and Description Press the phone button. 2. Access the desired contact through SYNC or use voice commands to place the second call. Once actively in the second call, press MENU. 3. Scroll to Join Calls, and press the OK button. Wait until the following message appears.
Page 336 SYNC (If Equipped) Press the phone button to enter the Phone Menu, then scroll to: Message Action and Description Phone Redial Press the OK button to redial the last number called. Press the OK button again to confirm. Call History Access any previously dialed, received or missed calls after you connect your Bluetooth-enabled cell phone to SYNC.
Page 337: Text Messaging
SYNC (If Equipped) Message Action and Description Vehicle Health Create and receive a diagnostic report card on your vehicle. Mobile Apps Interact with SYNC-capable mobile applications on your smartphone. Sys Settings Access Bluetooth Devices menu listings and advanced menu listings. Exit Press the OK button to exit the phone menu.
Page 338 The system sends each text message with the following signature: This message was sent from my Ford. I n f o r ma t i o n P r o v i d e d b y :...
Page 339: Accessing Your Phone Settings
SYNC (If Equipped) Message Action and Description Download now Allows you to download your unread messages to SYNC. To download the messages, press the OK button to select. The display indicates the system is downloading your messages. When downloading is complete, SYNC returns you to the inbox.
Page 340 SYNC (If Equipped) Message Action and Description Press the OK button then select one of the following and press the OK button again to confirm. Message Notification On Message Notification Off Modify Phone- Modify the contents of your phone book (such as add, delete, down- book load).
Page 341 SYNC (If Equipped) Press the Phone button to enter the Phone Menu, then scroll to: Message Action and Description Sys Settings Press the OK button. Bluetooth device Press the OK button. Select one of the following: See Using SYNC With Your Phone (page 328). Connect BT Connect a previously paired Bluetooth-enabled phone.
Page 342 SYNC (If Equipped) Advanced and set prompts, languages, defaults, perform a master reset, install an The Advanced menu allows you to access application and view system information. To access the advanced menu, press the phone button to enter the Phone Menu, the scroll to: Message Action and Description...
Page 343: Sync Applications And Services
SYNC (If Equipped) Message Action and Description Press the OK button and scroll to select. Press the OK button to confirm. System info Access the Auto Version number as well as the FDN number. Press the OK button to select. Return Exit the current menu.
Page 344 SYNC (If Equipped) If a crash deploys an airbag (excluding www.SYNCMyRide.ca or knee airbags and rear inflatable safety www.syncmaroute.ca. belts [if equipped]) or activates the fuel See Supplementary Restraints System pump shut-off, your SYNC-equipped (page 35). Important information about vehicle may be able to contact emergency airbag deployment is in this chapter.
Page 345 SYNC (If Equipped) In the Event of a Crash 911 Assist Privacy Notice Not all crashes will deploy an airbag or When you turn on 911 Assist, it may activate the fuel pump shut-off (the disclose to emergency services that your triggers for 911 Assist).
Page 346 Action and Description Vehicle Health (Report) The system will run a vehicle health report of your vehicle's diagnostic systems and send the results to Ford where it combines with scheduled maintenance information, open recalls, other field service actions and vehicle inspection items that still need servicing by an authorized dealer.
Page 347 Run Report Press the OK button for SYNC to run a health report of your vehicle's diagnostic systems and send the results to Ford where it combines with scheduled maintenance information, open recalls, other field service actions and vehicle inspection items that still need servicing by an authorized dealer.
Page 348 For more information, see SYNC Services Terms and Conditions at www.SYNCMyRide.com. If you do not want Ford or its service providers to collect your vehicle travel information or other information identified in the Terms and Conditions, do not subscribe or use the service.
Page 349 SYNC (If Equipped) Connecting to SYNC Services Using the Phone Menu Press the phone button, then scroll to: Message Action and Description SYNC Apps Press the OK button. Services Press the OK button. The display indicates the system is connecting. 2.
Page 350 SYNC (If Equipped) Voice command Action and Description The live operator can assist you by searching for businesses by name or by category, residential addresses by street address or by name or specific street intersections. The system may prompt you to speak with an operator when it has difficulty matching your voice request.
Page 351: Sync Applink
SYNC (If Equipped) SYNC Services quick tips You can even access your account outside your vehicle. Just use the number on your phone's call history. Traffic and Directions features do not function properly but information services and the 411 connect and text message features are available.
Page 352: Using Sync With Your Media Player
SYNC (If Equipped) Press the Menu button to the SYNC menu and scroll to: Menu item Action and description SYNC-Media Press the OK button. Mobile Apps Press the OK button and scroll through the list of available applications and select your desired app. Scroll until the app name followed by For more information, please visit: "Menu", is displayed (such as, Stitcher...
Page 353 SYNC (If Equipped) To Connect Using Voice Commands Plug the device into the USB port. See E142599 USB Port (page 322). Press the voice button and when prompted say: Voice command Action and Description USB [1] You can now play music by saying any of the appropriate voice commands.
Page 354: What's Playing
SYNC (If Equipped) What's Playing? When a track is playing, you can ask the system to tell you what is currently playing. Press the voice button and when prompted say: Voice command Action and Description Whats This? | Whats The system reads the metadata tags of the playing track, Playing? and if the metadata tags are populated, the system will tell you what track is playing.
Page 355: Media Menu Features
SYNC (If Equipped) Voice command Voice command Search The system searches all Autoplay Off Genre ___ the data from your Autoplay Turn autoplay on to listen to indexed music and, if [on] music processed during available, begins to play indexing. Turn autoplay off to the chosen type of music.
Page 356 SYNC (If Equipped) Press the AUX button, then the Menu button to enter the Media Menu. You can then scroll to: Message Action and Description Play Menu Play your music by artist, album, genre, playlists, tracks, similar music or to simply, play all.
Page 357: Accessing Your Play Menu
SYNC (If Equipped) Message Action and Description Autoplay Press the OK button to turn autoplay on to listen to music processed during indexing. Turn autoplay off to allow the indexing process to finish before the system plays any of your music. Mobile Apps Interact with SYNC-capable mobile applications on your smartphone.
Page 358 SYNC (If Equipped) Message Action and Description Play all indexed media (tracks) from your playing device in flat file mode, one at a time in numerical order. Artists Sort all indexed media by artist. Once selected, the system lists and then plays all artists and tracks alphabetically. If there are fewer than 255 indexed artists, the system lists them alphabetically in flat file mode.
Page 359 SYNC (If Equipped) Message Action and Description Browse USB Explore all supported digital media on your media device connected to the USB port. You can only view media content which is compatible with SYNC; other files saved are not visible. Press the OK button.
Page 360 SYNC (If Equipped) Message Action and Description Press the OK button. When find SYNC appears in the display, press the OK button again. 2. Follow the directions in your phone's manual to put your phone into discovery mode. A six-digit PIN appears in the display.
Page 361 SYNC (If Equipped) You can then scroll to: Message Action and Description Sys Settings Press the OK button. Bluetooth device Press the OK button. You can then select one of the following: Confirmation Prompts Have SYNC guide you by asking questions, helpful hints or ask you for a specific action.
Page 362: Sync Troubleshooting
SYNC (If Equipped) Use the website at any time to check your SYNC TROUBLESHOOTING phone's compatibility, register your account and set preferences as well as Your SYNC system is easy to use. However, access a customer representative via an should questions arise, see the tables online chat (during certain hours).
Page 363 SYNC (If Equipped) Phone issues Issue Possible cause(s) Possible solution(s) Depending upon your phone, you may have to grant SYNC permission to access your phonebook contacts. Make sure to confirm when prompted by your phone during the phonebook download. I am having trouble This is a phone-dependent Go to the website to review connecting my phone to...
Page 364 SYNC (If Equipped) USB and media issues Issue Possible cause(s) Possible solution(s) I am having trouble This may be a possible Try turning off the device, connecting my device. device malfunction. resetting the device, removing the device's battery, then trying again. Make sure you are using the manufacturer's cable.
Page 365 SYNC (If Equipped) Vehicle Health Report and Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I received a text that I did You did not activate your This is a free feature, but you not activate Vehicle Health account on the website.
Page 366 SYNC (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) SYNC does not understand You may be using the wrong Review the phone voice what I am saying. voice commands. commands and the media You may be speaking too voice commands at the soon or at the wrong time.
Page 367 SYNC (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) The system may not be Make sure you are saying the reading the name the same contacts exactly as they are way you are saying it. listed. For example, if you Contacts in your phonebook save a contact as Joe may be very short and...
Page 368 AppLink. Also, some may have a "Ford SYNC" setting, so check the app's settings menu on the phone. My phone is connected, my Sometime apps do not...
Page 369 SYNC (If Equipped) AppLink issues Issue Possible cause(s) Possible solution(s) On an iPhone with iOS7+, to force close an app, double tab the home button then swipe up on the app to close it. Tab the home button again, then select the app again to restart it.
Page 370 SYNC phone listed in SYNC's bluetooth ports apps can to find. If the app has a "Ford Mobile Apps Menu. use to connect. If you have SYNC" setting, disable that more AppLink apps on your...
Page 371: Accessories
Contact an authorized Ford dealer for the accessory Exterior Style manufacturer's limited warranty details and request a copy of the Ford Licensed • Keyless entry. Accessories product limited warranty from • Side window deflectors.
Page 372 • If you or an authorized Ford dealer add any non-Ford electrical or electronic accessories or components to your vehicle, you may adversely affect battery performance and durability. In...
Page 373: Extended Service Plan (Esp)
3. BaseCARE - Covers 84 components. Transferable Coverage 4. PowertrainCARE - Covers 29 critical If you sell your vehicle before your Ford components. Extended Service Plan coverage expires, Ford Extended Service Plan is honored by you can transfer any remaining coverage all authorized Ford dealers in the U.S.,...
Page 374: Scheduled Maintenance
Premium Maintenance Plan that covers all Service Plan. Ford Extended Service Plan scheduled maintenance, and selected is the only service contract backed by Ford wear items. The coverage is prepaid, so Motor Company of Canada, Limited. you never have to worry about affording Depending on the plan you purchase, Ford your vehicle’s maintenance.
Page 375: Scheduled Maintenance
If you do not use Ford authorized parts they you sell or trade it. Keep all receipts for may not meet our specifications and completed maintenance with your vehicle.
Page 376: Owner Checks And Services
When the oil change message appears in Additives and Chemicals the information display, it is time for an oil This owner's manual and the Ford change. Make sure you perform the oil Workshop Manual list the recommended change within two weeks or 500 miles additives and chemicals for your vehicle.
Page 377: Multi-Point Inspection
Scheduled Maintenance Check every month Engine oil level. Function of all interior and exterior lights. Tires (including spare) for wear and proper pressure. Windshield washer fluid level. Check every six months Battery connections. Clean if necessary. Body and door drain holes for obstructions. Clean if necessary. Cooling system fluid level and coolant strength.
Page 378: Normal Scheduled Maintenance...........375 I N F O R Ma T I O N P R O V I D E D B Y
Scheduled Maintenance Multi-Point inspection Accessory drive belt(s) Hazard warning system operation Battery performance Horn operation Engine air filter Radiator, cooler, heater and air conditioning hoses Exhaust system Suspension components for leaks or damage Exterior lamps operation Steering and linkage Tires (including spare) for wear and proper Fluid levels ;...
Page 379: Normal Maintenance Intervals
Scheduled Maintenance When to expect the message prompting you to change your oil Interval Vehicle use and example Normal Normal commuting with highway driving 7500-10000 miles No, or moderate, load or towing (12000-16000 km) Flat to moderately hilly roads No extended idling Severe Moderate to heavy load or towing 5000-7499 miles...
Page 380 Scheduled Maintenance At every oil change interval as indicated by the information display Inspect the steering linkage, ball joints, suspension, tire-rod ends, driveshaft and U- joints. Inspect the wheels and related components for abnormal noise, wear, looseness or drag. Do not exceed one year or 10000 miles (16000 kilometers) between service intervals. Reset the Intelligent Oil-Life Monitor after engine oil and filter changes.
Page 381: Special Operating Conditions Scheduled Maintenance
Scheduled Maintenance Perform the services shown in the SPECIAL OPERATING following tables when specified or within CONDITIONS SCHEDULED 3,000 mi (4,800 km) of the message MAINTENANCE appearing in the information display prompting you to change your oil. If you operate your vehicle primarily in any •...
Page 382 Scheduled Maintenance Operating in dusty or sandy conditions (such as unpaved or dusty roads) Inspect frequently, service Replace engine air filter. as required Every 5,000 mi (8,000 km) Inspect the wheels and related components for abnormal noise, wear, looseness or drag. Rotate tires, inspect tires for wear and measure tread depth.
Page 383 During long periods useful life. Ford Motor Company, however, of trailer towing with outside temperatures urges you to have all recommended above 70°F (21°C) and at wide-open...
Page 384: Scheduled Maintenance Record
Scheduled Maintenance SCHEDULED MAINTENANCE RECORD Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 385 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 386 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 387 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 388 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 389 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 390 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 391 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 392 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 393 Scheduled Maintenance Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Dealer stamp Repair Order #: Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 394: End User License Agreement
COMPANY nor its suppliers shall be include software licensed or owned by liable for any damages arising out of Ford Motor Company and its affiliates errors in the speech recognition ("FORD MOTOR COMPANY"). Those process. It is your responsibility to...
Page 395 • Single EULA: The end user • Additional Software/Services: The documentation for the DEVICES and SOFTWARE may permit FORD MOTOR related systems and services may COMPANY, third party software and contain multiple EULAs, such as service suppliers, its affiliates and/or...
Page 396 DEVICES. electronic form, you may print one copy of UPGRADES AND RECOVERY MEDIA: such electronic documentation. If the SOFTWARE is provided by FORD EXPORT RESTRICTIONS: You MOTOR COMPANY separate from the acknowledge that the SOFTWARE is DEVICES on media such as a ROM chip, subject to U.S.
Page 397 Should you have any questions concerning are driving. Pull over in a safe and legal this EULA, or if you desire to contact FORD manner before attempting to access a MOTOR COMPANY for any other reason,...
Page 398 Appendices substitute for your personal judgment. Your Responsibilities and Assumptions of Any route suggestions made by this Risk system should never replace any local • You agree to each of the following:(a) traffic regulations or your personal Any use of the SOFTWARE while judgment or knowledge of safe driving driving an automobile or other vehicle practices.
Page 399 "AS IS" AND “AS AVAILABLE”, WITH ALL COMPANY SHALL BE FOUND IN THE FAULTS AND WITHOUT WARRANTY OF WARRANTY INFORMATION INCLUDING ANY KIND, AND FORD MOTOR COMPANY WITH YOUR OWNER GUIDE. TO THE HEREBY DISCLAIMS ALL WARRANTIES EXTENT THAT THERE IS ANY CONFLICT...
Page 400 Consumer-Related Disputes will also litigate any dispute in small claims court apply. To commence arbitration, submit a in your county of residence or FORD Commercial Arbitration Rules Demand for MOTOR COMPANY’S principal place of Arbitration form to the AAA. You may...
Page 401 AAA’s and arbitrator’s fees and expenses. If you reject FORD MOTOR (i) Severability. If the class action waiver COMPANY’S last written settlement (Section e) is found to be illegal or...
Page 402 Appendices 3. Software License (a) observe all traffic laws and otherwise drive safely; • Subject to your compliance with the (b) use your own personal judgment while terms of this Agreement, TeleNav driving. If you feel that a route suggested hereby grants to you a personal, by the TeleNav Software instructs you to non-exclusive, non-transferable license...
Page 403 Appendices ii. violates any law, statute, ordinance or is dependent on the accuracy of regulation, including but not limited to laws navigation, as the maps or functionality and regulations related to spamming, of the TeleNav Software are not privacy, consumer and child protection, intended to support such high risk obscenity or defamation, or applications, especially in more remote...
Page 404 Appendices REASON WHATSOEVER (INCLUDING, to the exclusive jurisdiction of the WITHOUT LIMITATION, ALL DAMAGES courts of the County of Santa Clara, REFERENCED HEREIN AND ALL California. The United Nations DIRECT OR GENERAL DAMAGES IN Convention on Contracts for the CONTRACT, TORT (INCLUDING International Sale of Goods shall not NEGLIGENCE) OR OTHERWISE), THE apply.
Page 405 Appendices conferred by implication, statute, inducement, estoppel or otherwise, and The headings in this Agreement are for TeleNav and its suppliers and licensors convenience of reference only, will not be hereby reserve all of their respective rights deemed to be a part of this Agreement, other than the licenses explicitly granted and will not be referred to in connection in this Agreement.
Page 406 Appendices HERE holds a non-exclusive license from positioning devices or any mobile or the United States Postal Service® to wireless-connected electronic or computer publish and sell ZIP+4® information. devices, including without limitation cellular phones, palmtop and handheld ©United States Postal Service® 2014. computers, pagers, and personal digital Prices are not established, controlled or assistants or PDAs.
Page 407 Appendices DAMAGES, DIRECT OR INDIRECT, WHICH Governing Law. The above terms and MAY RESULT FROM THE USE OR conditions shall be governed by the laws POSSESSION OF THE INFORMATION; OR of the State of Illinois [insert “Netherlands” FOR ANY LOSS OF PROFIT, REVENUE, where European HERE Data is used], CONTRACTS OR SAVINGS, OR ANY without giving effect to (i) its conflict of...
Page 408 Appendices If the Contracting Officer, federal Gracenote Data shall also apply to such government agency, or any federal official content and such content providers shall refuses to use the legend provided herein, be entitled to all of the benefits and the Contracting Officer, federal protections set forth herein that are government agency, or any federal official...
Page 409 Appendices Gracenote uses a unique identifier to track OF THE GRACENOTE SOFTWARE OR ANY queries for statistical purposes. The GRACENOTE SERVER. IN NO CASE WILL purpose of a randomly assigned numeric GRACENOTE BE LIABLE FOR ANY identifier is to allow Gracenote to count CONSEQUENTIAL OR INCIDENTAL queries without knowing anything about DAMAGES OR FOR ANY LOST PROFITS...
Page 410 Index Anti-Theft Alarm..........63 Arming the Alarm..........63 Disarming the Alarm...........63 Appendices.............391 See: Four-Wheel Drive........164 Audible Warnings and Indicators....91 Direction Indicator Chime........91 Headlamps On Warning Chime.......91 Key in Ignition Warning Chime......91 Parking Brake On Warning Chime....91 See: Climate Control..........113 Audio Control..........68 About This Manual...........7 Media................69 Seek, Next or Previous........69 See: Brakes............172...
Page 411 Index Bonnet Lock Changing the 12V Battery......252 See: Opening and Closing the Hood..243 Battery Management System.......254 Booster Seats..........23 Changing the Engine Air Filter....262 Changing the Wiper Blades.....255 Types of Booster Seats........24 Brake Fluid Check.........251 Checking MyKey System Status....49 Brakes..............172 Checking the Wiper Blades.....254 Childminder Mirror.........82 General Information...........172 Breaking-In.............220...
Page 412 Index Cruise Control..........70 Engine Coolant Check........247 Principle of Operation........186 Adding Engine Coolant........247 Cruise control Checking the Engine Coolant......247 See: Using Cruise Control........186 Recycled Engine Coolant........248 Customer Assistance.........228 Severe Climates..........248 What You Should Know About Fail-Safe Cooling..............248 Engine Immobilizer Data Recording..........9 See: Passive Anti-Theft System.....62 Engine Oil Check..........245 Event Data Recording...........9...
Page 413 Fog Lamps - Front See: Parking Brake..........173 See: Front Fog Lamps.........77 Hazard Warning Flashers......224 Foot Pedals See: Adjusting the Pedals........71 See: Using Hill Descent Control....179 Ford Credit............11 Headlamp Adjusting (U.S. Only)..............11 See: Adjusting the Headlamps.....255 Four-Wheel Drive.........164 Headlamp Removal Front Fog Lamps..........77 See: Removing a Headlamp......256...
Page 414 Index Information Display Control.......70 Information Displays........92 General Information..........92 Jump Starting the Vehicle......225 Information Messages........103 Connecting the Jumper Cables....225 4WD Messages.............112 Jump Starting............226 AdvanceTrac / Traction Control Preparing Your Vehicle........225 Messages............104 Removing the Jumper Cables.......226 Alarm Messages..........104 Battery and Charging System Messages............104 Blind Spot Information System Keyless Entry............59...
Page 415 Index Locking and Unlocking.........53 Moonroof............83 Activating Intelligent Access......53 Bounce-Back............84 Autolock..............54 Opening and Closing the Moonroof.....84 Auto Relock............54 Venting the Moonroof........84 Motorcraft Parts..........303 Autounlock.............55 MyKey Troubleshooting........51 Battery Saver............55 MyKey .............46 Illuminated Entry..........55 Illuminated Exit.............55 Principle of Operation........46 Power Door Locks..........53 Remote Control.............53 Smart Unlocks for Integrated Keyhead Normal Scheduled Maintenance...375 Transmitter............54...
Page 416 Index Power Windows..........80 Refueling............153 Accessory Delay...........80 Easy Fuel Capless Fuel System....154 Remote Control..........42 Bounce-Back............80 One-Touch Down..........80 Car Finder..............44 One-Touch Up............80 Integrated Keyhead Transmitter.....42 Window Lock............80 Intelligent Access Key.........42 Protecting the Environment......14 Memory Feature...........45 Remote Start............44 Replacing the Battery.........43 Sounding the Panic Alarm........44 Rear Axle............171 Remote Start...........121 Rear Parking Aid..........181...
Page 417 Index Safety Precautions........151 Starting a Gasoline Engine.......146 Satellite Radio..........319 Automatic Engine Shutdown......148 Satellite Radio Electronic Serial Number Failure to Start............147 (ESN)..............320 Guarding Against Exhaust Fumes....149 Satellite Radio Reception Factors....320 Important Ventilating Information....149 SIRIUS® Satellite Radio Service....320 Stopping the Engine When Your Vehicle is Troubleshooting..........321 Moving...............148 Scheduled Maintenance Record....381...
Page 418 Using Hill Descent Control......179 Using MyKey With Remote Start Changing Tires With a Tire Pressure Systems............50 Monitoring System........292 Understanding Your Tire Pressure Vehicles With Ford-Approved Aftermarket Monitoring System ........292 Remote Start Systems.........50 Tires Vehicles With Non-Ford-Approved See: Wheels and Tires........272 Aftermarket Remote Start Towing a Trailer..........205...
Page 419 Index Using SYNC With Your Phone....328 Accessing Features Through the Phone Menu..............332 Warning Lamps and Indicators....88 Accessing Your Phone Settings....336 4X2................90 Making a Call............331 4X4 Auto..............90 Pairing a Cell Phone for the First 4X4 HIGH..............91 Time..............328 4X4 LOW..............91 Pairing Subsequent Cell Phones....329 Anti-Lock Braking System........88 Phone Options during an Active Call..331 Battery..............88...
Page 420: Wrecker Towing
Index Wrecker Towing See: Transporting the Vehicle......216 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...
Page 421 I n f o r ma t i o n P r o v i d e d b y : Expedition (TB7) Canada/United States of America, enUSA, First Printing...

This manual is also suitable for:

Expedition 2016

Ford 2016 EXPEDITION Owner's Manual

Introduction

Environment

Child Safety

Seatbelts

Supplementary Restraints System

Keys and Remote Controls

Mykey

Locks

Security

Power Running Boards

Steering Wheel

Pedals

Wipers and Washers

Lighting

Windows and Mirrors

Instrument Cluster

Information Displays

Climate Control

Seats

Universal Garage Door

Auxiliary Power Points

Storage Compartments

Starting and Stopping the Engine

Fuel and Refueling

Transmission

Four-Wheel Drive

Rear Axle

Brakes

Traction Control

Stability Control

Terrain Response

Parking Aids

Cruise Control

Driving Aids

Quick Links

Troubleshooting

Related Manuals for Ford 2016 EXPEDITION

Summary of Contents for Ford 2016 EXPEDITION