Table of Contents
Advertisement
Quick Links
n
Overall length
No
load speed
IRPM)
Collet size
3
mm or 1
/E''
19,000
295
mm
I1 1 518'')
MODEL 903D
MODEL 903DW
With Fast Charger
Net
weight
0 7 kg 11.5
Ibs)
INSTRUCTION MANUAL
Battery Cartridge 9000
" ' " I
Model DC9100 Fast Charger
Voltage
I
Charging time
I
Input
I
output
9 6 V
I
1
Hr
I
A C
only 5 0 H r
~
60 Hz
I
D C
9
6 V
~~
~~
~
Manufacturer reserves the right t o change specifications without notice.
Note: Specifications may differ from country to country.
Advertisement
Table of Contents
Related Manuals for Makita 903D
Summary of Contents for Makita 903D
- Page 1 Note: Specifications may differ from country to country. load speed Overall length IRPM) 19,000 I1 1 518'') Model DC9100 Fast Charger Input only 5 0 H r MODEL 903D MODEL 903DW With Fast Charger " ' " I weight 0 7 kg 11.5 Ibs) output 60 Hz...
- Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool w i t h finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Do not short the battery cartridge: (1) Do n o t touch the terminals...
- Page 6 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into...
- Page 7 Installing or removing wheel point CAUTION : Always be sure that tool installing or removing the wheel point. Remove the guide from the tool when it is installed on the tool. Loosen the wing bolt and pull the guide off the front end of the tool.
- Page 8 Switch action CAUTION Before inserting the battery cartridge into the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released. Operation Switch on the tool and wait until the wheel point attains full speed. Then apply the wheel point to the blade gently.
- Page 9 Chain blade sharpening attachment Read the instruction manual of y o : ' the top plate filing angle 0.030" (0.76 0.035" (0.89 mm), filinq anqle d a t e 2. Three sizes of wheel points are available: Select proper wheel point for chain cutters to be sharpened. (5.5 mm).
- Page 10 This will allow approx. 1/5 of the wheel point diameter to protrude above the chain cutters chain manufacturers re- commend. NOTE : Always check the protrusion of the wheel point using the gauge after tightening the wing bolt securely because the guide may move when you tighten the wing bolt secure- Place the wheel point on the chain so that the wheel point fits into the chain cutter and the guide line...
- Page 11 5. The depth gauges (or "rakers") fourth chain sharpening and lowered if found to be too high. do this, place the guide on the gauge shown in the figure and turn the guide until the wheel point fits into the ap- propriate depth gauge slot in the gauge.
- Page 12 Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. adjustment...
- Page 13 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present accessories or attachments should be used only in the proper and intended manner.
- Page 14 May-09-89 CORDLESS BLADE SHARPENER Model 903D Note: The switch and other part configurations may differ from country to country.
- Page 15 MODEL 9 0 3 D ‘ : “ O M DESCRIPTION Name Plate Housing Set lWath Item 11 1 Battery Holder Switch Compression Spring Switch Lever Collet Note. The switch and other specificat,ons may differ from country to country. part ‘...
- Page 16 MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date original purchase.