Advertisement
Quick Links
Cordless Drill
Dimensions
( L x W x
HI
Capacities
No load speed
SteeliWood
Wood screw
10
mm
(3/8") MODEL 6 O l O S D
10
mm
(318") MODEL 6OlOSDW
With Quick Charger
Net
weight
INSTRUCTION MANUAL
SPEC IF I CAT IONS
Model 6010SD
I
205
mm
x 48
mm x 175 mm
0.95 kg
1
12.1 Ibsl
(8" x 1-7/8" x 6-718")
1
600 R / m m
10 mm
(318"l
I
13/16"
x
3 4 " )
4 . 5 mm
x
20 mm
Model DC7020
Quick Charger
1
DC 7 . 2 V .
I
3
Hr
A . C . only
50
Hz -
60 Hz
*
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country
to
country.
Advertisement
Related Manuals for Makita 6OLOSDW
Summary of Contents for Makita 6OLOSDW
- Page 1 Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country Cordless Drill (3/8") MODEL 6 O l O S D (318") MODEL 6OlOSDW No load speed 600 R / m m (8" x 1-7/8" x 6-718") country.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to that keys and adjusting wrenches are removed from tool before turn- ing it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. To reduce risk of injury, charge only MAKITA type recharge- CAUTION able batteries. Other types of batteries may burst causing personal injury and damage.
- Page 5 7. Do not touch the drill bit or the workpiece immediately after operation, they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. damp wet locations. step-up transformer, an engine generator or DC FOR CORDLESS DRILL plastic tool body t o prevent electric not attempt...
- Page 6 HOW TO USE Charging Connect the charging plug t o the charg- ing connector, then plug in the charger t o the power receptacle. Charging takes 3 hours. CAUTION: The battery your new tool charged. You will need to charge it be- use.
- Page 7 After use, chuck return tool. storage cavity Switch action Set the reversing switch lever just in front of the trigger switch to Forward Reverse ( R E V ) . Then pull the trigger to t u r n the tool ON and release OFF.
- Page 8 Holding tool Hold the tool as shown in the figure. When drilling a large diameter hole, the tool frimly with both hands. Drilling in metal Punch a small hole in the metal to prevent the bit from skittering when starting to drill a hole.
- Page 9 Screwdriving Match your bit to your screw. Phillips bits Select your screws and nominal diameter with the chart the right. 2. Slotted bits Select a slotted bit screw slot, the bit and/or screw head may be damaged. Overload protector The overload protector automatically cuts 20-30 is prolonged.
-
Page 10: Maintenance
Always be sure that the tool is switched off before attempting to perform inspection or maintenance. T o maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 11 Bits Phillips Slotted Square drill bit Quick charger 12-volt Quick charger Chuck key S10 Keyless drill chuck tool specified in your Makita Size # 5 F (A.C. only) this...
- Page 12 (3/8") CORDLESS DRILL Model 6010SD Note: The switch and other part configurations may differ from country country.
- Page 13 MODEL 6010SD ' Z M DESCRIPTION Screw 3x20 Set (With Item H o u ~ i n g Holder 6 Drill Chuck S10 Screw M5x18 Gear Plane Bearing Motor Plane Bearing 3 Gear 13-58 Plane Bearing 3 Note The switch and other part specifications may differ from country to country DESCRIPTION Current Relay a n c e...
- Page 14 MAKmA LlMmED O N E YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.