Table of Contents
Advertisement
Cordless Driver Drill
Capacities
Steel
I
Wood
I
Wood screw
I
Machine screw
Equipped with Electric Brake
MODEL 62211)
MODEL 6221DW
With Fast Charger
weight
I
Net
No
load
speed
Dimensions
IL
x
W
x
H)
IRPM)
INSTRUCTION MANUAL
10 mm
(318")
SPECIFICATIONS
Model 6221D
I
I
15
mm
5.1 mm x 35 mm
mm 1114,,1
202 mm x 50 mm x 218 mm
1.4 kg
(518")
13/16, x 1-318")
~
700
17-15/16" x 1-31/32" x 8-19/32")
13.1 lbsl
~~
Voltage
Input
output
Charging time
9.6 V
A.C. onlv 50 Hz
-
60 Hz
D.C. 7.2 V. 9.6 V
t
Manufacturer reserves the right t o change specifications without notice.
Note: Specifications may differ from country t o country.
1 Hr.
Advertisement
Table of Contents
Related Manuals for Makita 6221D
Summary of Contents for Makita 6221D
- Page 1 Cordless Driver Drill INSTRUCTION MANUAL SPECIFICATIONS Model 6221D Capacities Steel Wood Wood screw 5.1 mm x 35 mm 10 mm (518") 13/16, x 1-318") (318") Voltage 9.6 V A.C. onlv 50 Hz Manufacturer reserves the right t o change specifications without notice.
- Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source w i t h voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user as well as damage t o the tool.
- Page 5 Before using battery charger, read all instructions and cautionary markings on (1) battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 9100. Other types of batteries may burst causing personal injury and damage. Do not expose charger t o rain or snow.
- Page 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 4OoC (104OF). or ABOVE Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used.
- Page 7 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge *To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing from the tool. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip...
- Page 8 Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck Hold the ring firmly and turn the sleeve clockwise to tighten the chuck.
- Page 9 Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work prolonged. 30 seconds before resuming operation. Wait 20 CAUTION : Always withdraw the tool from the workpiece before resuming operation. If the tool cannot be withdrawn, hold the tool firmly when turning on the tool, to overcome a strong reaction.
- Page 10 NOTE : Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the chart.
- Page 11 To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed Makita replacement parts. is switched off and the battery cartridge is removed before Makita Authorized or Factory Service Centers, always using...
- Page 12 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories The accessories or attachments should be used only in the proper and intended manner. Bits Size...
- Page 13 Fast charger Model DC9700 Part No. 1 131 03-2 1 2 V for *Charger Model DC9112 Part No. 1131 10-5 Fast charger Model DC1201 Part No. 113126.0 91 00 Battery cartridge Part No. 19201 9-4 Battery cover Part No. 41 4938-7 Plastic carrying case...
- Page 14 Sep -08-'94 CORDLESS DRIVER DRILL Model 6221D Note: The switch and other part configurations may differ from country to country.
- Page 15 MODEL 6221D ' : N E, " DESCRIPTION MACHINE Housing Set [With Item Name Plate Tapping Screw BT4x18 Battery Holder Switch Lever Switch Lever Plate Spring 27 C O m D W S S l O n COmpreSSlOn Spilng Washer...
- Page 16 Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under Tools-Electric' " Every Makita tool is thoroughly inspected and tested before leavinn the factory. It is warranted to be free onginal purchase Should any freieht Prepad. t o 1001.