Playing A Disc; Region Codes - Magnavox MRD300 User Manual

1
STANDBY
POWER ON•OFF
ON
iR SENSOR
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5
5 D I S C D I R E C T P L AY
OPEN•CLOSE
PROGRESSIVE
STOP SCAN TUNER•BAND TV•AUX
DVD
3
1
SOURCE
1 2 3
SLEEP
4 5 6
7 8 9
>10 0
VOL
MUTE SELECT
DISPLAY MENU
OK
4
OPEN/
CLOSE
SET UP
PREV
PLAY/PAUSE NEXT
í É Å ë
STOP FF
REW
5 à Ç á
TITLE ANGLE ZOOM GOTO
LANGUAGE SUBTITLE N/P DIM
REPEAT A/B SHUFFLE PROGRAM
DISC SKIP DISC NO SLOW/MEM CD MODE
ST/MONO LISTENING AUDIO
No picture!!
Check the AV (Audio/Video) mode on
your TV.
* Usually this channel is between the lowest and
highest channels and may be called FRONT,
A/V IN, or VIDEO.
* Or, you may go to channel 1 on your TV, then
press the Channel down button repeatedly
until you see the Video In channel.
* Or, your TV remote control may have a button
or switch that chooses different video modes.
* Do not use channel 3 or 4 on the TV unless
you are using an RF modulator.
* See your TV manual for more details.
Detailed playback features and additional functions are described in the
DVD VIDEO DIGITAL SURROUND SYSTEM
5 DVD CHANGER
MUTE SELECT PREVIOUS NEXT PLAY•PAUSE
PROGRESSIVE SCAN
5 DVD CHANGER
Make sure your DVD system and
TV are connected and turned on!

Playing a disc

1
Press POWER ON•OFF at the front panel to turn the power on.
You can also press the SOURCE button on the remote until "DISC X" appears on the display panel.
2
Turn on the TV and select the correct Video In mode.
You should see the blue Philips DVD background screen on the TV (if no disc in the DVD system).
3
Press OPEN•CLOSE 0 at the front panel of the DVD system and load a
disc, then press the OPEN•CLOSE 0 again to close the disc tray.
Make sure the disc label is facing up. For double-sided discs, load the side you want to play face up.
4
Playback will start automatically. If not, press É Å button.
If a disc menu appears, use 3 4 1 2 buttons on the remote to make the necessary selection, then
press OK to confirm. Or, use the numeric keypad on the remote to select features. Follow the
instructions given in the disc menu.
5
To stop playback, press STOPÇ.

Region Codes

DVDs must be labeled for ALL regions or Region 1, in order
to play on this DVD system.
accompanying owner's manual.
VOLUME
PHONES
DVD system Video Output Selection for
1) Press SETUP button.
The Setup Menu main page appears on the TV
screen.
2) Select 'GENERAL SETUP, ' then press OK.
3) Press 4 button to select 'VIDEO OUT, '
then press 2 button.
4) Press 3 / 4 button to select and highlight:
S-VIDEO - if you use the S-Video
connection.
CR CB Y - if you use the Component
Video Pr/Cr Pb/Cb Y connection.
5) Press OK button to confirm.
The SETUP button to clear the screen when
completed.
Note: If you have problem access to the Setup Menu, use the VIDEO OUT for connecting the
DVD system to your TV (VIDEO IN). This connection enables you to access to the SETUP
MENU and make the selection for the type of video output (S-VIDEO or CR CB Y).
2
Proper Playback
SETUP MENU - - MAIN PAGE
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
PREFERENCES
EXIT SETUP
TV DISPLAY
GOTO GENERAL SETUP PAGE
ANGLE MARK
OSD LANG
VIDEO OUT
SCR SAVER
MAIN PAGE
SET VIDEO OUTPUT
1
ALL
- - GENERAL PAGE - -
S-VIDEO
CR CB Y