Timer Recording - Magnavox ZV450MWB Owner's Manual

SOURCE
.@/:
.@/:
1 1
GHI GHI
4 4
PQRS PQRS
7 7
. .
DISC MENU
s s
TITLE
j
F
REC MODE
REC
I
CM SKIP
SEARCH
Note
• If you have not set the clock yet:
"Manual Clock Setting" menu will appear instead of
the timer programming list at step 1. Continue with
the step 4 in "Manual Clock Setting" on page 26
before setting a timer programming.
• Use [s / B] to move the cursor to the left and the
right in "Timer Programming" menu.
• If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is
about to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes
before the programmed starting time, and the
recording in progress (for VCR) will be canceled
UNLESS their recording channels are the same. If their
recording channels are the same, the timer recording
will start without canceling the recording currently in
progress. In this case, the recording of the same
channel will be made on both DVD and VCR.
• Cancel the timer-standby mode by pressing
[TIMER SET] before operation for either DVD or VCR.
When finished operating, press [TIMER SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
E9C80UD.indd 37 E9C80UD.indd 37

TIMER RECORDING

STANDBY-ON
DTV/TV DISPLAY OPEN/CLOSE OPEN/CLOSE
A A
ABC DEF
ABC DEF
2 2 3 3
JKL JKL MNO MNO
5 5 6 6
TUV TUV WXYZ WXYZ
8 8 9 9
SPACE SPACE CLEAR CLEAR
0 0
SETUP SETUP
o o
OK OK
B B
RETURN
p p
B
B i i
h g C C
CHANNEL
-- +
VCR DVD TIMER TIMER
AUDIO
TIMER TIMER
SET
D.DUBBING SET RAPID PLAY
You can program the unit to record up to 8 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space or
a cassette tape with a erase-protection tab.
1
Press [TIMER].
2
Use [K / L] to select a program
number, then press [OK].
Timer Programming
Date Start End CH
1. ---
2. ---
3. ---
4. ---
3
Use [K / L] to enter the date, then
press [B].
Timer Programming
Date Start End CH
1. JAN/01 --:-- --:--
2. ---
3. ---
4. ---
When pressing [L] at the
current date, the date will
change as follows.
e.g.) January 1st
JAN/01
p
Daily
p
MON-SAT
p
MON-FRI
p
SAT
p
FRI
p
p
SUN
p
JAN/31
4
Use [K / L] or [the Number buttons]
to enter the start and end time, then
press [B].
Timer Programming
Date Start End CH
1. JAN/01 11:57AM --:--
2. ---
3. ---
4. ---
Instructions continue on the next page.
VCR DVD
DVD
Mode
VCR
VCR DVD
DVD
Mode
VCR
12 DVD
VCR DVD
DVD
Mode
VCR
12 DVD
EN EN 37 37
2006/12/19 14:03:14 2006/12/19 14:03:14