Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Sunbeam Pro Glide SR8700
Summary of Contents for Sunbeam Pro Glide SR8700
- Page 1 MASTER SERIES Pro Glide ® Steam Generator User Guide...
-
Page 2: Table Of Contents
Contents Sunbeam’s Safety Precautions Features of your Pro Glide ® Steam Generator Using your Pro Glide ® Steam Generator Care and Cleaning of your Pro Glide ® Steam Generator Troubleshooting Guide Ironing Tips & Tricks Ironing Chart Important instructions –... -
Page 3: Sunbeam's Safety Precautions
• Never leave an appliance unattended while in use. If you have any concerns regarding the performance and use of your appliance, please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. -
Page 4: Features Of Your Pro Glide Steam Generator
Features of your Pro Glide ® Steam Generator Constant Steam Button When ironing for long periods the constant steam button can be activated to produce continuous steam eliminating the need to hold the trigger down during ironing. Iron rest Place the iron on the heat resistant iron rest between garments. - Page 5 Thermostat light The thermostat light illuminates to indicate that the iron sole plate is heating, and goes out when it has reached the temperature selected on the temperature dial. The thermostat light cycles on and off during ironing as the iron sole plate maintains the selected temperature.
- Page 6 Features of your Pro Glide Steam Generator continued ® Eco Steam Mode (SR8710) Steam Rate Dial The steam generator will use 20% less The steam rate can be energy when Eco steam is selected.” selected by turning the and arrow pointing to the steam dial. steam rate dial to preferred level of steam.
-
Page 7: Using Your Pro Glide Steam Generator
For best performance, we recommend NOTE: Sunbeam recommend using steam the use of Sunbeam Water Demineraliser generators with the SB8300 Couture or Sunbeam Demineralised Water Ironing Board which has a metal tray available from selected retailers. - Page 8 Using your Pro Glide Steam Generator continued ® Using your iron stable at the new setting by allowing the thermostat to cycle once (the thermostat 1.Insert the plug into a 230/240 volt light will turn on / off once). power outlet and turn the power on. 2.Select the power button to turn the unit on.
- Page 9 Using your Pro Glide Steam generator continued ® 5.Press and hold the steam release The water tank can be refilled at any trigger to iron with steam. Use the time during ironing but the boiler may constant steam button for continuous take a few minutes to return to the steam when ironing tough garments.
- Page 10 Using your Pro Glide Steam Generator continued ® Calc Clean Reminder any button, trigger or dial needs to be pressed to power back up the boiler and Mineral deposits in tap water solidify the iron. Allow the iron to heat up until when the water is heated and can build the thermostat light on the iron goes out up in the steam holes and boiler system...
-
Page 11: Steam Generator
The Calc Clean light illuminates after approximately 20 hours of use. exterior of your iron as these will damage the surface. Calc Clean instructions – using Sunbeam Cleaning the steam holes Ironing System Descaling Tablets To remove build up from the steam holes... - Page 12 (SR0100) are available from selected department stores and electrical retailers. Calc Clean instructions – using lemon juice Alternatively, if you do not have Sunbeam Figure 8 Ironing System Descaling Tablets, you can use lemon juice to remove the scale build 4.
- Page 13 Care and Cleaning continued 8. Shake the unit back and forth to dislodge any scale build up on the base of the boiler. Leave for 10 minutes. 9. Shake the unit again to swirl the solution around inside the boiler. 10.
-
Page 14: Troubleshooting Guide
Troubleshooting Guide Problem Possible Reason Solution Water is spitting The temperature of the Turn the soleplate temperature up to Silk from the soleplate. soleplate is set below or above and wait for the soleplate to reach the Silk setting. the selected temperature. Before using the steam generator on a garment direct a shot of steam into the air to release any remaining The unit has been left... -
Page 15: Ironing Tips & Tricks
Ironing Tips and Tricks Tip # 1 - Iron shirts like a pro Tip # 6 - Ironing the seam Start with the collar, working from the outer Always press seams in the same direction edges into the middle. Iron the shoulder they were made. -
Page 16: Ironing Chart
Ironing Chart Fabric Temperature Setting Steam Setting Eco Setting (SR8710) Ironing recommendation Acrylic • Dry iron on wrong side Dry iron on wrong side while still Acetate • damp or use spray to dampen Iron on wrong side. Use an Silk •... - Page 17 Notes...
- Page 18 Notes...
- Page 19 This Sunbeam product is covered by a 24 month replacement or repair warranty, which is in addition to your rights under the Month Australian Consumer Law (if your product Replacement was purchased in Australia) or New Zealand Guarantee Consumer Guarantees Act (if your product was purchased in New Zealand).
- Page 20 Unit 3, Building D, 26 Vestey Drive, Mt Wellington Auckland New Zealand. Sunbeam Corporation Limited | ABN 45 000 006 771 Sunbeam Corporation is a division of GUD Holdings Limited. Sunbeam is a registered trademark. Pro Glide is a trademark of Sunbeam Corporation Made in China to Sunbeam’s specification.