Advertisement
Pro Steam Irons
Instruction Booklet
This book covers the use and care of the following Sunbeam Irons:
SR4100 Pro Steam Polished shot and spray iron
SR4200 Pro Steam Teflon
SR4250 Pro Steam Teflon
SR4300 Pro Steam Teflon
Please read these instructions carefully
and retain for future reference.
®
shot and spray iron
®
shot and spray iron
®
shot and spray iron with Auto-off
Advertisement
Related Manuals for Sunbeam Pro Steam SR4100
Summary of Contents for Sunbeam Pro Steam SR4100
- Page 1 Pro Steam Irons Instruction Booklet This book covers the use and care of the following Sunbeam Irons: SR4100 Pro Steam Polished shot and spray iron ® SR4200 Pro Steam Teflon shot and spray iron ® SR4250 Pro Steam Teflon shot and spray iron ®...
-
Page 2: Table Of Contents
Contents Sunbeam’s Safety Precautions Features of your Pro Steam Iron Using your Pro Steam Iron Care and Cleaning Ironing Tips and Tricks Ironing Chart Important instructions – retain for future use. -
Page 3: Sunbeam's Safety Precautions
• Iron only on an ironing board. • Always unplug the iron from the power outlet before filling or emptying the water tank. • An iron takes approximately 30 minutes to cool down. Allow the iron to cool completely before storing. Sunbeam is very safety conscious when • Do not use an appliance for any purpose designing and manufacturing consumer products, other than its intended use. but it is essential that the product user also • Do not place an appliance on or near a hot gas exercise care when using an electrical appliance. flame, electric element or on a heated oven. -
Page 4: Features Of Your Pro Steam Iron
Features of your Sunbeam Pro Steam Iron Powerful shot of steam Pressing the shot of steam button instantly produces a powerful shot of steam to remove stubborn wrinkles. Vertical shot of steam Pressing the shot of steam button with the iron in an upright position produces a vertical shot of steam, which is ideal for steaming curtains and suits, and removing creases from delicate fabrics. Fine spray mist Pressing the spray button provides a fine mist spray to dampen hard-to-iron fabrics. Easy-fill water inlet The water inlet cover opens fully to allow easy filling of the water tank, without bubbling or spilling. Large water tank Holds 280ml of water for continual high steam performance without having to refill the tank regularly. - Page 5 Long cord with 360º cord outlet The cord outlet is ideal for left or right hand use, and provides greater versatility and ease of movement when ironing. The flexible grommet protects the cord from fraying. Safety auto-off (Model SR4300 only) The iron automatically switches itself off if left in the ironing position (horizontal) for 30 seconds, or in the heel rest position (vertical) for 15 minutes. (For more information on the safety auto off feature see page 7). Thermostat light Illuminates to indicate that the iron is heating and goes out when it has reached the selected temperature. The thermostat light cycles on and off during ironing as the iron maintains the selected temperature. Variable steam The steam dial allows you to select the desired steam output for each garment. Alternatively, select the DRY setting to iron without steam. Temperature dial Allows you to select the desired temperature for each garment. The adjustable temperature dial also indicates the amount of steam recommended for use on each temperature setting.
-
Page 6: Using Your Pro Steam Iron
Using your Sunbeam Pro Steam Iron Before first use Using your iron Remove any adhesive stickers, plastic covers 1. I nsert the plug into a 230/240 volt power or cardboard sleeves from the soleplate. outlet and turn the power on. Ensure that all adhesive is removed by 2. T urn the temperature dial to the desired rubbing the soleplate with a cloth dampened setting by aligning the setting on the with methylated spirits. dial with the temperature indicator. The Fill the water tank and empty the water. This thermostat light (positioned on the top will rinse out any foreign particles remaining of the handle) will illuminate to indicate in the water tank from the manufacturing that the iron is heating to the selected process. temperature. When the thermostat light goes out the iron has reached the selected NOTE: When turned on for the first time, your temperature and is ready to iron. new iron may give off vapours for up to 10 minutes. This is due to the initial heating of NOTE: When the temperature dial is changed the materials used. It is safe, not detrimental... - Page 7 Using your Sunbeam Pro Steam Iron (continued) Using the shot of steam NOTE: If the tank has run dry, it may be necessary to re-prime the pump after filling The shot of steam can be used whether dry the iron with water. or steam ironing when the temperature dial is set to any temperature above the two dot Using the spray mist (••) setting. The spray mist can be used whether dry 1. Ensure the tank is at least ¼ full of or steam ironing to pre-dampen hard to water. iron fabrics. 2. Select the desired temperature and wait 1. Ensure the tank is at least ¼ full of until the thermostat light goes out. water. 3. Press the shot of steam button several 2. Press the spray button during ironing times with the iron on the soleplate to to release a fine mist from the spray prime the pump. nozzle. The safety auto-off feature...
-
Page 8: Care And Cleaning
Care and Cleaning After each use To clean the steam holes To remove build up from the steam holes 1. Turn the power off and remove the plug which may affect steam performance, use from the power outlet. a cotton wool tip moistened in methylated 2. A llow the iron to cool before winding the spirits. cord around the built-in cord wrap. Cleaning the Teflon® Select non-stick soleplate Storage (SR4200 & SR4300) Always store the iron on its heel rest. The non-stick coating reduces sticking of NOTE: Do not store the iron with the soleplate fabrics and starches to the soleplate. Do facing down, or in the carton. not iron over sharp objects such as buttons, studs and zippers, as these will scratch the Cleaning surface. To clean the exterior of your iron, wipe over Wipe the soleplate with a damp soft cloth with a damp soft cloth and wipe dry. -
Page 9: Ironing Tips And Tricks
Ironing Tips and Tricks Tip # 27 - Iron shirts like a pro Tip # 13 - Ironing the seam Start with the collar, working from the outer Always press seams in the same direction they were made. When a garment is edges into the middle. Iron the shoulder next, followed by the cuffs and sleeves. Place produced, the fibres will naturally settle in the direction they were initially pressed, the collar at the narrow end of the board so that one front panel of the shirt is extended so it’s best not to iron against the grain. flat. Iron the front panel from shoulder to Tip # 26 - Sort types of fabric shirt tail. Rotate to iron the back of the shirt. Sort articles to be ironed according to the Rotate and complete the remaining front type of fabric. This will reduce the need to... -
Page 10: Ironing Chart
Ironing Chart Fabric Temp setting Ironing Ironing recommendation MINIMUM Acrylic Dry iron on reverse side of fabric Min to • MINIMUM Dry iron on reverse side of fabric Acetate while still damp Min to • MINIMUM Nylon Iron on reverse side of fabric Min to • SYNTHETIC Polyester Iron on reverse side of fabric • SYNTHETIC Rayon Iron on reverse side of fabric • SYNTHETIC Mainly dry iron. Steam can be used under Viscose • manufacturer's instructions Iron on reverse side of fabric. Use an ironing SILK Silk cloth to prevent shine marks • • and use regular shots of steam Check label and follow manufacturer’s WOOL Cotton Blends instructions. Use setting for the fibre • •... - Page 11 2 years of purchase (3 months commercial use) due to faulty materials or manufacture, we will replace it for you free of charge. Should you experience any difficulties with In Australia you are entitled to a your appliance, please phone our customer replacement or refund for a major failure and service line for advice on 1300 881 861 in for compensation for any other reasonably Australia, or 0800 786 232 in New Zealand. foreseeable loss or damage. You are also Alternatively, you can send a written claim entitled to have the goods repaired or to Sunbeam at the address listed below. replaced if the goods fail to be of acceptable On receipt of your claim, Sunbeam will quality and the failure does not amount to seek to resolve your difficulties or, if the a major failure. appliance is defective, advise you on how Should your appliance require repair or to obtain a replacement or refund. service after the guarantee period, contact Your Sunbeam 2 Year Replacement your nearest Sunbeam service centre. Guarantee naturally does not cover misuse For a complete list of Sunbeam’s authorised...
- Page 12 In New Zealand Visit www.sunbeam.co.nz Or call 0800 786 232 is a registered trademark. ‘Pro Steam’ is a registered trademark of Sunbeam Corporation. ‘Teflon’ is a registered trademark of DuPont. Made in China. Due to minor changes in design or otherwise, the product may differ from the one shown in this leaflet.