Bluetooth Operations; Aux Operations; Trouble Shooting - Clarion CZ505E Owner's Manual And Installation Instructions

Bluetooth Operations

Audio Streaming Operations
What is audio streaming?
Audio streaming is a technique for transferring
audio data such that it can be processed as a
steady and continuous stream. Users can stream
music from their external audio player to their car
stereo wirelessly and listen to the tracks through
the car's speakers. Please consult your nearest
Clarion dealer for more information on the
product of wireless audio streaming transmitter
offered.
CAUTION
Please avoid operating your connected mobile
phone while audio streaming as this may cause
noise or choppy sound on the song playback.
Audio streaming may or may not resume after
telephone interrupt as this is dependent on mobile
phone.
System will always return to Radio mode if audio
streaming is disconnected.
Note:
Be sure to read the "Pairing" section before
proceeding.
Play / Pause a track
1. Push the [ 4 ] button to pause audio playback.
2. To resume audio playback, push the [ 4 ] knob
again.

AUX Operations

Press [SRC / ] button on the panel to select
"AUX".
AUX is just for audio content with 3.5mm Jack
connector plugged into audio-in socket on the
front panel.
AUX Input sensitivity setting
1. Press and hold the [ DISP ] button
(1 sec.).
12
CZ505E
Selecting a track
Track-up
1. Press the [ ] button to move to the
beginning of the next track.
2. Each time the [ ] button is pressed,
playback proceeds to another track in the
advancing direction.
Track-down
1. Press the [ ] button to move to the
beginning of the previous track.
2. Each time the [ ] button is pressed,
playback proceeds to previous track in the
reverse direction.
Note:
Playing order will depend on Bluetooth audio
player. When [ ] button is pressed, some
A2DP devices will restart the current track
depends on the duration of playback.
During music streaming playback, "A2DP
and HFP" will be shown on the display. When
A2DP device is disconnected,
" DISCONNECT" will be shown on the display
and return to previously selected audio
source. Some Bluetooth audio players may
not have play / pause synchronized with this
unit. Please make sure both device and main
unit are in the same play / pause status in BT
MUSIC mode.
2. Press [ ] or [ ] button to select
"AUX SENS".
3. If the output level of the connected
external audio player is "HIGH", rotate
[VOLUME] knob and choose "MID" or
"LOW". And if the output level is "LOW",
choose "MID" or "HIGH".

6. TROUBLE SHOOTING

GENERAL
Problem Cause
Unit fuse blown.
Unit can not
power on.
Car battery fuse blown.
Unit can not
power on.
Nothing happens
when buttons are The microprocessor has
pressed. malfunctioned due to noise, etc.
Display is not
accurate.
Improper audio output connection. Check wiring and correct.
Volume set too low.
No/low audio Speakers damaged.
output.
Heavily biased volume balance.
Speaker wiring is in contact with
metal part of car.
Non-standard disc used.
Speaker power rating does not
Poor sound quality
match unit.
or distortion.
Wrong connections.
Speaker is shorted.
Unit resets itself Incorrect connection between ACC
when engine is off. and Battery.
DISC Player
Problem Cause
Another disc is already loaded.
Disc cannot be
There is an object installed inside
loaded.
the unit.
Compact disc is dirty.
Sound skips or is
Compact disc is heavily scratched
noisy.
or warped.
Sound is bad when Condensation may form on the internal
power is first turned lens when the car is parked in a humid
on. place.
Measure
Replace with new fuse of correct rating.
Replace with new fuse of correct rating.
Turn off the power and remove the DCP.
Press the [RESET] button with a thin rod.
Note:
When the [RESET] button is pressed, turn off
the ACC power.*
* When the [RESET] button is pressed,
preset radio stations, titles, etc. stored in
memory are kept.
Increase volume level.
Replace speakers.
Adjust the channel balance to center position.
Insulate all speaker wiring connections.
Use a standard disc.
Replace speakers.
Check wiring and correct.
Check wiring and correct.
Check wiring and correct.
Measure
Eject the disc before loading the new one.
Remove the object inside the unit.
Clean the compact disc with a soft cloth.
Replace with a compact disc with no
scratches.
Let dry for about 1 hour with power on.