Stereo; Mono; Bridge; Output Application - Mackie M1200/M1400 Owner's Manual

The AMP MODE switch determines the in-
put signal routing within the M•1200/M•1400
amplifier. Shipped from the factory, the switch
is set to STEREO. This is correct for about 90%
of the applications using an amp like this
(hence the TYPICAL indicator near it). But
you may be in the 10% bracket, requiring spe-
cial input routing within the amp.
AMP MODE should be configured before
operation — if you must change it during per-
formance, turn down the GAIN
a precaution to protect the speakers from any
inadvertent pops or thumps.

STEREO

mode (separate left and right
inputs, separate left and right outputs) is the
typical setup for amplifying stereo signals.

MONO

mode (sometimes called Dual-
Mono – one mono input, two mono outputs) is
for sending a mono signal to two different
speaker sets, with separately-adjustable GAIN
controls.

BRIDGE

mode (sometimes called
Bridged-Mono – one mono input, one mono
output) uses both sides of the amp to double
the power to one speaker set. With two M•1200
power amplifiers, each set to BRIDGE mode,
you can deliver as much as 1200 watts per
amplifier.
If you set the AMP MODE
switch in MONO or
BRIDGE, use the CHAN-
NEL 1 inputs only — the
CHANNEL 2 inputs go no-
where in this case.
Note: There is one exception to this rule. If you
have the OUTPUT APPLICATION switched to
SUBWOOFER, the inputs to Channels 1 and 2
are summed regardless of the AMP MODE
). Also, BRIDGE
setting (see
quires special connections at the SPEAKER
OUTPUTS
.
BRIDGE
In STEREO mode, the M•1200 Power
Amplifier can deliver 600 watts per side into
2 ohms. If that's not enough, you can use two
M•1200s, each in BRIDGE mode, and deliver
1200 watts per amplifier into 4 ohms. The
M•1400 produces 630 watts per side into
2 ohms in STEREO and 1260 watts into 4 ohms
in BRIDGE mode. Or, you can use one amp in
BRIDGE mode to power a monaural system.
Finally, BRIDGE mode is also popular for
subwoofer applications — but please see
SUBWOOFER
for a special subwoofer surprise.
20
To use all the M•1200/M•1400's power to
drive one speaker cabinet using BRIDGE mode,
you'll have to do four things:
1. Turn off the power to the M•1200/M•1400.
2. Set the AMP MODE
3. Connect the positive side of the speaker
cable to the Channel 1 red (+) binding post.
4. Connect the negative side of the speaker
cable to the Channel 2 red (+) binding post.
5. (Okay, make that five things!) Use only the
controls as
CHANNEL 1 INPUT
the SUBWOOFER OUTPUT APPLICATION).
The CHANNEL 1 GAIN control adjusts the
output level of the amplifier. The CHANNEL 2
GAIN control has no effect.
Once again: Before making connections to
an amp or reconfiguring an amp's routing, turn
the power off, make the changes, then turn the
power back on.

OUTPUT APPLICATION

The OUTPUT APPLICATION switch should
be configured before you turn on the amplifier.
This switch allows you to choose between three
different configurations:
LIMITER ON (TYPICAL). This is the normal
configuration: full-bandwidth audio with pro-
tective limiting (please see
LIMITER OFF is also full bandwidth audio,
but without protective limiting (please see
SUBWOOFER mode, with built-in low-pass
filter, no protective limiting (please see

LIMITER

The LIMITER is not designed to alter your
sound — it's just there to protect your speak-
ers from clipping. Its effect is virtually
transparent, meaning you probably won't even
notice any audible difference. We recommend
mode re-
that you leave it engaged (via OUTPUT APPLI-
CATION
If you're working at quiet levels all the time,
or you've already placed a compressor/limiter
in the signal path, or if you just hate compres-
sion, you can leave the LIMITER out of the
circuit (via OUTPUT APPLICATION
ping. Clipping occurs when the output voltage
no longer linearly follows the input voltage
and simply stops. This causes a sine wave to
switch to BRIDGE.
(unless you're using
).
), hence the TYPICAL label below it.
The LIMITER senses when
the amp is about to be
overdriven and attenuates
the overall level just enough
to keep the signal from clip-
).
).
).