Symbol P360 Quick Reference Manual
  1. Manuals
  2. Brands
  3. Symbol Manuals
  4. Barcode Reader
  5. P360
  6. Quick reference manual
Symbol P360 Quick Reference Manual

Symbol P360 Quick Reference Manual

Memory scanners
Hide thumbs Also See for P360:
Table of Contents

Advertisement

Quick Links

P360/460 Memory Scanners
Quick Reference Guide

Advertisement

Table of Contents
loading

Related Manuals for Symbol P360

Summary of Contents for Symbol P360

  • Page 1 P360/460 Memory Scanners Quick Reference Guide...

  • Page 2: Warranty

    Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

  • Page 3: Installing Cables

    They can operate in both corded and battery-powered cordless modes. There are several versions available: 1D P460: the batch retail version. 1D P360: the batch industrial version. This Quick Reference Guide provides basic instruction on the set up and use of these scanners.

  • Page 4: Disconnecting Cables

    P360/460 Memory Scanners Turn the cable twist-lock 1/8 turn clockwise to seat it. Gently pull the cable to ensure it is properly seated. Plug the other end of the cable to the host computer. Disconnecting Cables Most hosts require RS-232 cables. All other hosts require Synapse cables. To disconnect the Phaser scanner cable: Power down all devices connected to the Phaser scanner cable.

  • Page 5: Replacing The Battery

    Quick Reference Guide Slide the battery towards the bottom of the scanner and pull the bottom of the battery up and out of the scanner. Replacing the Battery Seat the battery fully in the scanner and then slide it up the handle. Replace the battery compartment cover and slide the release latch up to secure the cover in place.

  • Page 6: Scanning 1D Bar Codes

    If you are not using one of the default applications, consult the Phaser Series Scanner Product Reference Guide (p/n 70-33629-xx) for programming instructions. If necessary, contact your local supplier or the Symbol Support Center for assistance. Scanning 1D Bar Codes If using the scanner in corded mode, ensure all cable connections are secure.

  • Page 7: Host Communication

    Bar Code Bar Code Scan the Entire Symbol • The scan beam must cross every bar and space on the symbol (as in the left bar code below). • Hold the scanner farther away for larger symbols. • Hold the scanner closer for symbols with bars that are close together.

  • Page 8: Beeper Indications

    Do not pour, spray or spill any liquid on the scanner. Regulatory Information All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and are labeled as required. Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol Technologies, could void the user's authority to operate the equipment.

  • Page 9: Health And Safety Recommendations

    Quick Reference Guide Health and Safety Recommendations Ergonomic Recommendations CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.

  • Page 10: Scanner Labeling

    P360/460 Memory Scanners Scanner Labeling C A U T I O N LASER LIGHT-DO NOT STARE INTO BEAM 630-680 nM LASER 1.0 mW MAX OUTPUT CLASS II LASER PRODUCT LASERLICHT - NICHT IN DEN STRAHL BLICKEN, LASER KLASSE 2 LUMIERE LASER-NE PAS REGARDER DANS LE FAISCEAU APPARIEL A LASER DE CLASSE 2.

  • Page 11: Power Supply

    Replace the battery when a significant loss of run time is detected. Batteries must be charged within the 32° to 104°F (0° to 40°C) temperature range. The standard warranty period for all Symbol batteries is 30 days, regardless if the battery was purchased separately or included as part of the mobile computer. For more...

  • Page 12: Radio Frequency Interference Requirements-Fcc

    Marking and European Economic Area (EEA) Statement of Compliance Symbol Technologies, Inc., hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/.

  • Page 13: Waste Electrical And Electronic Equipment (Weee)

    Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Symbol al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.symbol.com/environmental_compliance.
  • Page 14 Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Symbol para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.symbol.com/environmental_compliance. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Symbol za reciklažo.
  • Page 15 Quick Reference Guide...
  • Page 16 +44 118 945 7360 Latin America Inside USA: 1-800-347-0178; Sales Support Outside USA: +1.954.255.2610 For the latest version of this guide go to: http://www.symbol.com/manuals. 70-33628-02 Revision C - May 2006 Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 http://www.symbol.com...

This manual is also suitable for:

P460

Table of Contents