Oki OKIPAGE 14ex Maintenance Manual page 150

LCD display
USER MNT
Press the
MENU key.
MENU
RESET
Press the
MENU key.
HEX DUMP
Press the
MENU key.
DRUM CNT
RESET
Press the
MENU key.
REC BUF
Press the
MENU key.
ECP
ENABLE *
OP MENU
ENABLE *
Press the
MENU key.
X ADJUST
0mm *
Press the
MENU key.
Y ADJUST
0mm *
2ND TRAY
5 *
PLACE PG
CENTER *
Press the
MENU key.
SETTING
0 *
JAMRCVR
ENABLE *
PWR SAVE
ENABLE *
Press the
MENU key.
INITIAL-
IZING
ON LINE
XXX
41356901TH Rev.2
After the completion
Press the
of processing
ENTER key.
MENU
RESET'NG
(See Table 4-1)
Press the
ENTER key.
ON-LINE
HEX DUMP
After the completion
Press the
of processing
ENTER key.
DRUM CNT
RESET'NG
AUTO
Press the
Setting of receiving buffer.
8KB
or key.
If you select a large value, the data transmitting time from
20KB
PC will be shortened, but Memory Overflow become easy
50KB
to happen.
100KB
1MB
Press the
A function to switch IEEE std 1284 parallel I/F ECP
ECP
or key.
mode Enable / Disable.
DISABLE
When Level-2 menu Centronics I/F bi-directional
Centronics is set to Disable, this becomes invalid,
regardless of the seting.
Press the
Writing into the EEPROM is performed after pressing the
or key.
OP MENU
ENTER key. Press the ON LINE key if you wish
DISABLE
to get out of this mode.
Press the
Writing into the EEPROM is performed after pressing the
or key.
ENTER key. Press the ON LINE key if you wish to get out of
X ADJUST
this mode.
+0.25mm
(Range of Adjustment: +2.00mm to -2.00mm; 0.25mm steps)
Press the
Writing into the EEPROM is performed after pressing the
or key.
X ADJUST ENTER key. Press the ON LINE key if you wish to get out of
+0.25mm this mode.
(Range of Adjustment: +2.00mm to -2.00mm; 0.25mm steps)
Press the
In the feeding destination selecting command (ESC&I#H) for
2ND TRAY
or key.
PCL5 Emulation, # designated for 2nd Tray is set.
1
As compared with mechanical setting position of paper being a
Press the
PLACE PG
center alignment, a printing image is moved in accordance with
ENTER key.
LEFT
the left alignment which is the same as HP (canon).
Enable only for PCL.
Press the
Used for fine adjustments when conspicuously scratchy printout results in certain
0 *
or key.
environment/special madia continuously
+ 1
Increment when light specs or snow flake like printout occurs in high density print
+ 2
(Note1)
areas.
- 1
Decrement when print results become faded.
- 2
Press the
JAMRCVR
Specifies the Recovery Enabled/Disable when an exit jam occurs.
or key.
• Enable : Guarantees Jam Recovery to allow the paper's bottom edge to pass
DISABLE *
• Disable : Increases the print performance for continuous printing that requires
Press the
A function to switch Power Save mode Enabel/Disable.
PWR SAVE
or key.
When DISABLE is selected, Power Save Level-2 menu will not appear.
DISABLE
ON-LINE
XXX
ON-LINE
XXX
OUT sensor as in normal usage.
large edit memory Demerit is, however, that this does not guarantee the Jam
Recovery after the paper's bottom edge pass WRITE sensor (after sending
print data to the drum (ID) is complete)
150 /