Canon imageRUNNER 2545 Series Service Manual Digest page 48

● <025: Answering machine connection function signal detection time>
Sets the signal detection time for the answering machine connection function operation.
When the answering machine connection function is operating, if the function does not
operate normally because the fax does not detect CNG signal sent from the line, raise this
parameter to increase the signal detection time.
● <027:V.21 low-speed flag preamble identification length>
Use it to detect the time of detection after which command analysis is started after
detecting V.21 low-speed command preambles continuously for a specific period of time.
● <056 - 061: Count type select >
Use it to confirm the count type indicated on the Counter Check screen, which appears in
response to a press on the Counter key.
When '0' is selected, count type will not be indicated.
056: Use it to indicate the type of software counter 1 of the control panel. The type of soft
counter 1 cannot be changed.
057: Use it to change the type of soft counter 2* of the control panel to suit the needs of the
user.
058: Use it to change the type of soft counter 3* of the control panel to suit the needs of the
user.
059: Use it to change the type of soft counter 4* of the control panel to suit the needs of the
user.
060: Use it to change the type of soft counter 5* of the control panel to suit the needs of the
user.
061: Use it to change the type of soft counter 6* of the control panel to suit the needs of the
user.
*:The default type settings of soft counter is different from models.
<Soft Counter Specifications>
The soft counters are classified a follows in terms of input numbers:
100s: total
200s: copy
300s: print
400s: copy + print
500s: scan
700s: received file print
800s: report pint
900s: transmitted scan
Guide to the Table
- 1:Count sheets of all sizes by one.
- 2:Count sheets of the large size by two.
- C:full color
- Bk:black mono
- L:large size (larger than A4/LTR)
- S:small size (A4/LTR or smaller)
MEMO:
To make a change so that B4 papers (for print) will be counted as large-size, use
service mode: make the following selections, and change bit 0 to '1': #SSSW>SW33.
To make a change so that B4 papers (for scan) will be counted as large-size, use
service mode: make the following selections, and change bit 2 to '1': #SSSW>SW33.
Serial Counter type
Print system
No. on
Bk 1-sided L
counter
check
screen
101 Total1 1 1 1
102 Total2 2 2 2
103 Total (L) 1 1 1
104 Total (S)
108 Total (Bk1) 1 1 1
109 Total (Bk2) 2 2 2
112 Total (Bk/L) 1 1 1
113 Total (Bk/S)
114 Total1 (2-sided)
115 Total2 (2-sided)
116 L (2-sided)
117 S (2-sided)
126 TotalA1 1 1
127 TotalA2 2 2
128 TotalA (L) 1 1
129 TotalA (S)
132 TotalA (Bk1) 1 1
133 TotalA (Bk2) 2 2
Bk 1-sided S Bk 2-sided L Bk 2-sided S
1 1 1 1 1
2 1 1 1 1
1
1 1 1 1
1 1 1 1 1
2 1 1 1 1
1
1 1 1 1
1 1 1 1 1 1
2 2 2 2 1 1
1 1 1 1
1 1
1 1 1 1
2 1 1 1
1
1 1 1
1 1 1 1
2 1 1 1
4
1 1
1 1
1 1
4-15