Bosch GSR Professional Original Instructions Manual page 24

OBJ_BUCH-690-003.book Page 24 Thursday, August 28, 2008 9:04 AM
24 | English
To remove the battery 8, press the unlocking
button 7 and pull out the battery toward the
front. Do not exert any force.
Auxiliary Handle (GSR 18 VE-2 LI/
GSB 18 VE-2 LI) (see figure A)
Operate your machine only with the auxilia-
ry handle 5.
The auxiliary handle 5 can be set to any position
for a secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 5 in
counterclockwise direction and swivel the auxil-
iary handle 5 to the desired position. Then
retighten the bottom part of the auxiliary handle
5 by turning in clockwise direction.
The clamping band 12 of the auxiliary handle
must be seated in the corresponding groove.
Changing the Tool (see figure B)
Before any work on the machine (e. g.,
maintenance, tool change, etc.) as well as
during transport and storage, set the rota-
tional direction switch to the centre posi-
tion. Unintentional actuation of the On/Off
switch can lead to injuries.
The drill spindle is locked when the On/Off
switch 11 is not pressed. This makes quick, con-
venient and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 1 by turning in rotation
direction , until the tool can be inserted. Insert
the tool.
Firmly tighten the collar of the keyless chuck 1
by hand in rotation direction
action ("click") is no longer heard. This automat-
ically locks the chuck.
The locking is released again to remove the tool
when the collar is turned in the opposite direc-
tion.
2 609 932 662 | (28.8.08)
Replacing the Drill Chuck
Before any work on the machine (e. g.,
maintenance, tool change, etc.) as well as
during transport and storage, set the rota-
tional direction switch to the centre posi-
tion. Unintentional actuation of the On/Off
switch can lead to injuries.
Removing the Securing Screw (see figure C)
The keyless chuck 1 is secured with a securing
screw 14 against unintentional loosening from
the drill spindle. Completely open the keyless
chuck 1 and unscrew the securing screw 14 in
rotation direction
curing screw has a left-hand thread.
Removing the Drill Chuck (see figure D)
Clamp the short end of an Allen key 15 into the
keyless chuck 1.
Place the machine on a stable surface (e. g. a
workbench). Hold the machine firmly and loos-
en the keyless chuck 1 by turning the Allen key
15 in rotation direction
keyless chuck by giving the long end of the Allen
key 15 a light blow. Remove the Allen key from
the keyless chuck and completely unscrew the
keyless chuck.
Mounting the Drill Chuck (see figure E)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a
tightening torque of approx. 15–25 Nm.
Screw the securing screw 14 in anti-clockwise
direction into the opened keyless chuck, tight-
ening torque approx. 2.5–3.5 Nm. Always use a
until the locking
new securing screw, as the threads are covered
with a thread-locking compound that loses its
effect after multiple usage.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one's health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
. Please note that the se-
. Loosen a tight-seated
Bosch Power Tools