Motorola DLR1020 User Manual
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Two-Way Radio
  5. DLR1020
  6. User manual
Motorola DLR1020 User Manual

Motorola DLR1020 User Manual

Hide thumbs Also See for DLR1020:
Table of Contents

Advertisement

Quick Links

See also: Quick Reference Manual
Two-Way Radios
User Guide
DLR1020, DLR1060 models

Advertisement

Table of Contents
loading

Related Manuals for Motorola DLR1020

Summary of Contents for Motorola DLR1020

  • Page 1 Two-Way Radios User Guide DLR1020, DLR1060 models...
  • Page 2 Open Source Software Legal Notices: This Motorola product contains Open Source Software. For more information regarding licenses, acknowledgements, required copyright notices and other usage terms, refer to the documentation for this Motorola product at: www.motorolasolutions.com/DLR...

  • Page 3: Table Of Contents

    Battery Features..... . 12 CONTENTS About the Li-Ion Battery ... . . 12 Battery Recycling and Disposal .
  • Page 4 Direct Call ......56 Motorola Limited Warranty for How Direct Call Works ....56 the United States and Canada .

  • Page 5: Product Safety

    When using the radio without a headset or satisfy FCC RF energy exposure requirements. earpiece, do not place the radio’s speaker For a list of Motorola-approved batteries and other directly against your ear. accessories, visit the following website which lists •...

  • Page 6: Introduction

    Thank you for purchasing the Motorola® DLR 8000 West Sunrise Boulevard Series Radio. This radio is a product of Plantation, Florida 33322 Motorola's 80 plus years of experience as a world leader in the designing and PACKAGE CONTENTS manufacturing of communications equipment.
  • Page 7 For product-related questions, contact: 1-800-448-6686 or visit us at: www.motorolasolutions.com/DLR English...

  • Page 8: Fcc Licensing Information

    Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC/IC to operate this radio and should not be made. To comply with FCC/IC requirements,...

  • Page 9: Batteries And Chargers Safety

    Use of accessories not recommended by To reduce risk of electric shock, unplug the Motorola may result in risk of fire, electric charger from the AC outlet before attempting shock, or injury.

  • Page 10: Operational Safety Guidelines

    OPERATIONAL SAFETY located at the bottom of the charger. GUIDELINES • Make sure that the cord is located where it will not be stepped on, tripped over, or subjected to • Turn the radio OFF when charging battery. water, damage, or stress. •...

  • Page 11: Radio Overview

    RADIO OVERVIEW PARTS OF THE RADIO Top Button Power Button Antenna Tx/Rx Audio Accessory Indicator Connector PTT (Push-To- Volume/Up-Down Talk) Button Control Buttons Channel / Menu Button Microphone Battery Speaker English...

  • Page 12: Power Button

    PTT button to exit. Speak clearly into the microphone when When in Advanced Configuration Mode, sending a message. Channel / Menu button gives access and Antenna allows navigation to set up special features. For models DLR1020 and DLR1060 the antennas are non-removable. English...

  • Page 13: The Lithium-Ion (Li-Ion) Battery

    The radio’s model is shown on the back of the radio and provides the following information: Table 1: DLR Series Radio Specifications Transmit Number of Frequency Model Power Antenna Band Channels (Watts) DLR1020 ISM 900 MHz Non-removable DLR1060 ISM 900 MHz Non-removable English...

  • Page 14: Battery Features

    Batteries with different capacities and Motorola batteries are designed specifically to operational life may be available in future. be used with a Motorola charger and vice About the Li-Ion Battery versa. Charging in non-Motorola equipment may lead to battery damage and void the The DLR Series radio comes equipped with a battery warranty.

  • Page 15: Battery Recycling And Disposal

    1-800-8-BATTERY specific requirements and information in your This internet site and telephone number also area. Motorola fully endorses and encourages provides other useful information concerning the recycling of Li-Ion batteries. In the U.S. and recycling options for consumers, businesses Canada, Motorola participates in the and governmental agencies.
  • Page 16 Installing the Lithium-Ion (Li-Ion) Battery Slide the latch at the top of the battery door to the unlock position and lift up the battery door at the center recess. Align the battery contacts with the tabs in the battery compartment. Insert the contact side of the battery first, then press the battery down to secure in place.

  • Page 17: Removing The Lithium-Ion (Li-Ion)

    Removing the Lithium-Ion (Li-Ion) Battery Turn OFF the radio. Slide the latch at the top of battery door to the unlock position and lift up the battery door at the center recess. Pull on the battery removal tab until battery is disengaged from battery compartment. Pull the battery away from radio.

  • Page 18: Holster

    Holster Power Supply, Adaptor and DLR Single Unit Charger (SUC) Tray Insert the radio into the base of the holster at an The radio is equipped with one DLR Single Unit angle. Press the radio against the back of the Charger (SUC) Tray and one Power Supply holster until the hooks on the holster are with Adaptor.

  • Page 19: Battery Life Information

    Battery Life Information When the Battery Save feature is set to ON (enabled by default), the battery life lasts longer. The following table summarizes battery life estimations: Table 2: Li-Ion Battery Life for DLR1020 and DLR1060 Battery Type Battery Save OFF...
  • Page 20 ATTENTION! Plug the AC adaptor into a power outlet. Turn the radio “OFF”. Always turn off the radios prior to charging. Insert the radio into the tray with the front of the Radios charge the best of room temperature. radio facing the front of the charger, as shown. Charging with the Drop-in Tray Make sure the radio is securely inserted all the Single Unit Charger (SUC)

  • Page 21: Estimated Charging Time

    To charge a battery, insert the battery into the Table 4: Motorola Authorized Batteries charger’s pocket by: Part Number Description Aligning the raised tab on each side of the battery with the corresponding groove on each side of the charger pocket.
  • Page 22 Charging a Radio and Battery using radio (with or without the Holster) or battery, but a DLR 12-Pocket Multi Unit-Charger not both. - MUC (Optional Accessory) Place the Multi-Unit Charger on a flat surface. Insert the power cord plug into the MUC’s dual pin connector at the bottom of the MUC.

  • Page 23: Dlr Series Charger Led Indicators

    DLR Series Charger LED Indicators Table 6: Charger LED Indicator Status LED Status Comments Green for approx. 1 sec Power On Steady red Charging Steady green Charged Red fast flash Error (*) Amber slow flash Standby (**) Flash red 1 time Battery low Flash amber 2 times Battery Level Status...
  • Page 24 Ensure the power cord is plugged securely into the charger socket with an appropriate AC outlet and there is power to the outlet (for DLR 12-Pocket Multi Unit Charger Tray only) Confirm that the battery used with the radio is Motorola Solutions authorized batteries listed in Table 4. English...

  • Page 25: Dlr Radios And Charger Compatibility

    DLR Radios and Charger Compatibility Table 7: DLR and CLS Chargers Compatibility Charging Compatibility Chargers DLR radio CLS radio with inserted standalone with inserted standalone battery batteries battery batteries     DLR SUC     DLR MUC ...
  • Page 26 Notes English...

  • Page 27: Getting Started

    GETTING STARTED For the following explanations, refer to “Parts Of The Radio” on page 9. RADIO BASIC OPERATION ON / OFF Button Long press to turn ON and OFF. Short press to check battery status. Top Button Press the Top Button to queue up for Private Reply (while (+) / (-) Buttons someone is talking in your...

  • Page 28: Turning Radio On/Off

    To mute, press and hold the (-) button (~2 before putting on the earpiece. Refer to seconds) until you hear the voice “Acoustic Safety” on page 3. Use only Motorola announcement “Mute”. approved accessories. Refer to “Audio Accessories” on page 113 for more information.

  • Page 29: Checking Battery Status

    CHECKING BATTERY STATUS using an in-line PTT on the earpiece accessory, always ensure the PTT To check the battery status, short press the button is pressed firmly until the power button. Refer to “Battery Status transmission is finished. Releasing the Information”...

  • Page 30: Talking To A Group In A Channel

    To exit Channel Change, press the PTT button or wait for the radio Channel / Menu timer to expire. PRIVATE REPLY DLR radio comes with the Top Button Solid Red configured to Private Reply Feature i.e. when Tx/Rx you hear someone talking on the radio, push Indicator the Top Button to queue for Private Reply LED when...

  • Page 31: Talk Range

    Available, Direct Call and Mute. It can also be PROFILE ID Number: ALL the radios in your disabled. For more details on how to configure fleet (independent of the channels that users the Top Button refer to “Advanced are assigned to) should use the SAME Configuration Mode”...
  • Page 32 DTR radios are to be added to an existing DLR radio fleet. For more details on DTR and DLR compatibility please contact your Motorola point of sale. For questions or comments related to this product, please contact Motorola:...

  • Page 33: Radio Status

    RADIO STATUS Radio Status Front LED Indicator Top Button LED Voice Prompt or Tone Indicator “Battery Level <Level>, Power Up Solid Red for 2 seconds Channel <Number>” Power Off Solid Red for 2 seconds Power Off chirps Fatal Error at Power up Double Blink Red Single Blink Orange Not Available...
  • Page 34 Notes English...

  • Page 35: Advanced Configuration Mode

    ADVANCED CONFIGURATION MODE The DLR Advanced Configuration Mode allows you to configure special settings in your radio without the need of programming cables or additional software. Advanced Configuration Mode gives access to customize the following features: • PROFILE ID Number, •...

  • Page 36: Entering Advanced Configuration Mode

    ENTERING ADVANCED CONFIGURATION MODE To enter the Advanced Configuration Mode, power UP using the ON / OFF button while pressing the PTT and (+) buttons simultaneously. ON / OFF Button (+) Button Power UP using the ON / OFF button while pressing the PTT and (+) buttons simultaneously to enter Advanced Configuration Mode...

  • Page 37: Browsing Advanced Configuration Options

    BROWSING ADVANCED CONFIGURATION OPTIONS Upon entering Advanced Configuration Mode, radio plays voice prompt “Programming Mode. Press Menu to continue”. Press Channel / Menu button to cycle through the Advanced Configuration options. Note: Long press the PTT button at any time to exit the Advanced Configuration Mode altogether. “Programming Mode.

  • Page 38: Profile Id Number

    PROFILE ID Number PROFILE ID Number – Current Value Once you press the Channel / Menu button, the radio announces the current PROFILE ID Number(*) and prompts you to change it. Press (+) or (-) button to enter the PROFILE ID Number sub-menu.
  • Page 39 PROFILE ID Number – Changing values Once you press either the (+) or (-) to enter the PROFILE ID Number sub-menu, the radio announces the first digit number value and prompts you to change it(*). Press (+) or (-) button again to change the first digit number.
  • Page 40 PROFILE ID Number – Sub-menu When you press (+) or (-) button to change the current digit, radio announces the value. Press Channel / Menu to continue to the next digit. Once in Digit 4, press Channel / Menu button again to continue to the next Advanced Configuration option.
  • Page 41 PROFILE ID Number – Value Modification Confirmation Once you have set the 4 digit PROFILE ID Number, the radio announces the entire new PROFILE ID Number value. Press Channel / Menu button to continue to the next Advanced Configuration option or hold down the PTT button to exit the Advanced Configuration Mode. Note: If the 4 digit PROFILE ID number set is not the numbers wanted upon moving to the next Advanced Configuration option, press the Channel / Menu button and cycle through the Advanced Configuration...

  • Page 42: Maximum Channels

    Press Channel / Menu button to continue to the next Advanced Configuration option. Note: The maximum number of channels you can set up in your radio is limited by the radio model. DLR1060 has maximum 6 channels and DLR1020 has maximum 2 channels. “Maximum channels <number>. To change, press plus or minus ”.

  • Page 43: Top Button

    Top Button Top Button – Current Feature Press the Channel / Menu button until the radio announces the current Top Button feature and prompts you to change. Press (+) or (-) button to enter the Top Button sub-menu. Alternatively, press Channel / Menu button to continue to the next Advanced Configuration option.
  • Page 44 Top Button – Sub-menu options Once you press the (+) or (-) button to enter the Top Button sub-menu, you can browse back and forward the different Top Button options using the (+) or (-) button. Radio will guide with voice prompts as you navigate through the features.

  • Page 45: Mic Gain

    MIC Gain Press the Channel / Menu button until the radio announces the MIC Gain setting and prompts you to change it. There is three MIC Gain settings to choose from – Low, Medium, High. The default MIC Gain value is “Medium”. Press the (+) or (-) button to change MIC Gain settings. Press Channel / Menu button to continue to the next Advanced Configuration option.

  • Page 46: Home Channel

    Home Channel Press the Channel / Menu button until the radio announces the Home Channel setting and prompts you to change it. There is two Home Channel settings to choose from – Disabled or Channel number (or channel name if alias was set up via CPS). The default setting of Home Channel is “Disabled”.

  • Page 47: Resetting To Factory Defaults

    RESETTING TO FACTORY DEFAULTS In order to reset your radios to the original factory defaults, power UP using the ON / OFF button while pressing PTT, (-) and (+) buttons simultaneously. Radio sounds resetting beeps and the voice prompt announces “Battery Level <battery level>, Channel <channel name>”. ON / OFF Button Power UP using the ON / OFF button while pressing...

  • Page 48: Radio Factory Default Settings

    Radio Factory Default Settings Table 3: Radio Advanced Configuration Mode Defaults Table 2: Radio Basic Feature Defaults Radio Advanced Radio Basic Default Configuration Default Feature Mode Power up Battery Status and PROFILE ID Number announcement Channel Name lock Quick press ON / OFF Battery Status Radio PROFILE ID button...
  • Page 49 Table 4: Radio Special Mode Defaults Radio Special Default Mode Enable restore Factory Default reset Enable Advanced Configuration Mode Enable Cloning Mode For all other radio defaults, please refer to the CPS. English...
  • Page 50 Notes English...

  • Page 51: Special Radio Call Features

    Application Example SPECIAL RADIO CALL FEATURES The use of this feature reduces the need for phone extensions or cell phone calls to talk PRIVATE REPLY privately. Simply call on the radio the name of the person you want to talk to privately. When The DLR radio Top Button is programmed by he or she responds to you, push the Private default as “Private Reply”.

  • Page 52: How Private Reply Works

    How Private Reply Works User A wants to talk to User B privately and presses the Top Button to queue up. User B is talking to a group of radios Note: Long pressing the Top Button a second time cancels the Private Reply queue. Group call in progress English...
  • Page 53 User A radio plays voice prompt “Private Reply” User B finishes talking to the Group while User and the Top Button starts blinking orange, A radio is still blinking orange indicating it is in showing user A is in queue waiting to talk queue for Private Reply call.
  • Page 54 User A presses PTT button to talk privately to Whenever user A or B presses the PTT button User B. The Top button LED indicator for both to reply back, they are talking privately to each radio A and radio B illuminate solid orange. other.
  • Page 55 If either one of the radio users takes too long to Radio user A (who initiated the Private Call), push the PTT button and reply back, (the can also end the call at any time by Long default “Private Hang Time” is 10 seconds), the pressing the Top Button.
  • Page 56 Radio user A and B join back the group transmission in their channel once the private call ends. Note: You can set the “Private Hang Time” and “Group Hang Time” to different values using the CPS. English...

  • Page 57: Private Reply Status Indicator

    Private Reply Status Indicator Table 1: Private Reply Status Indicator Private Reply Status Top Button LED Indicator Voice Prompt or Tone Private Reply request in queue (initiated using Top Button press) – Blink Orange “Private Reply” Initiator party Private conversation initiated (using the PTT button) –...

  • Page 58: Direct Call

    DIRECT CALL Refer to “Customer Programming Software (CPS)” on page 83 for more information. The Direct Call Feature allows a user to call Application Example another pre-determined user that has been mapped into the radio Top Button one-on-one Set up your employees to be able to contact privately (this feature needs to be directly and privately their supervisor, the pre-programmed via CPS*).
  • Page 59 User A presses the PTT button to talk privately to User B (who is NOT in a radio conversation), the TOP Button LED indicators of both A & B radios will illuminate solid orange. Radio B plays voice prompt “Private” indicating that the incoming call is a Direct Private Call.
  • Page 60 Whenever either user A or B presses the PTT If any of the radio users takes too long to push button to reply back, they are talking privately to the PTT button and reply back, (the default each other. (Radio plays a distinctive Private “Private Hang Time”...
  • Page 61 Radio user A (who initiated the Direct Call), can also end the call by Long pressing the Top Button. The radio plays voice prompt “Private Over” on both radio A and B to indicate that the private call is over. The TOP button LED indicator goes OFF.

  • Page 62: Direct Call Status Indicator

    Direct Call Status Indicator Note: To initiate Direct Call, press the Top Button followed by the PTT button to talk directly and privately to the pre-set user. Table 2: Direct Call Status Indicator Direct Call Status Top Button LED Indicator Voice Prompt or Tone Direct Call initiated (using Top Blink Orange...
  • Page 63 Private Reply and Direct Call faster gets to talk privately to B. The other user Frequently Asked Questions (FAQ) hears a “busy” or rejection tone. If I change my mind and want to exit the What happens if a person Private Reply or request for Private Call (or I pressed the top Direct Call User B, but User B does not want to button by mistake), how do I get out of the...
  • Page 64 if the Top Button was pressed outside the 4 long pressing the Top Button. However, if you seconds Group Hang Time). are the call receiver, you will have to wait for the radio to time out (i.e. no communications What happens if I want to Private Reply to a detected for more than 10 seconds) OR person that just finished talking? change the channel.
  • Page 65 Long Press the Top Button to exit the private – Would I be still able hear the group conversations in my channel if I don’t press queue mode (Top Button LED indicator should the PTT button? turn off) and press the PTT button to reply back Yes, you should be able to still hear to the group call.

  • Page 66: Call All Available

    CALL ALL AVAILABLE How do I know when the radio is no longer in Private Mode conversation? Note: This feature is useful for users with more than 1 or 2 channels. You are no longer in a private conversation if the Top Button LED indicator is not illuminating Call All Available feature allows the ability to solid orange and is either blinking or switched...
  • Page 67 The DLR radio times out a Call All Available Application Example communication after 4 seconds of inactivity. An employee in a retail shop uses a DLR1060 This is to avoid all users being tied up (6 channel radio) with the Top Button indefinitely in an unnecessary group programmed to Call All Available.

  • Page 68: How Call All Available Works

    How Call All Available Works All users in Channel 3 and 4 are available (nobody is transmitting). Talking User B and C busy in Private Call Talking CHANNEL 4 AVAILABLE Listening CHANNEL 3 AVAILABLE CHANNEL 2 BUSY English...
  • Page 69 User D in Channel 3 initiates Call All Available by pressing the radio Top Button(*). “Call All Available” Talking User B and C busy in Private Call Talking CHANNEL 4 AVAILABLE All users in Channel 3 and 4 are AVAILABLE Listening (Nobody is transmitting).
  • Page 70 All users from Channel 3 and 4 are brought into a temporary “super channel” group. User D then presses the PTT button and start talking to all available users in both channels. Talking User B and C busy in Private Call Talking CHANNEL 4 LISTENING TO USER D...
  • Page 71 All radios Top Buttons in Channel 3 and 4 are solid orange indicating that Call All Available is in progress. Talking User B and C busy in Private Call User D continues talking Talking to all available users CHANNEL 4 LISTENING TO USER D Listening CHANNEL 3...
  • Page 72 User D finished talking [Top Button LED indicator still solid orange(*)]. User E presses the PTT button and starts talking to all available users. All users in Channel 3 and 4 now hear User E. All radios Top Buttons are solid orange indicating that Call All Available is in progress.
  • Page 73 Once all users finished communicating (no transmissions for more than 4 seconds), the radios time out and end the Call All Available “super channel” group. All users in channel 3 and 4 return to their original talk channels. Talking User B and C busy in Private Call Talking CHANNEL 4...

  • Page 74: Call All Available Status Indicator

    Call All Available Status Indicator Note: To initiate Call All Available, press the Top Button followed by the PTT button to talk to all available users in different channels. Table 3: Call All Available Status Indicator Call All Available Status Top Button LED Indicator Voice Prompt or Tone Call All Available initiated (using...

  • Page 75: Page All Available

    PAGE ALL AVAILABLE Page All Available option can be assigned either to the Top Button or to an extra Note: This feature is useful for users with more channel(**). than 1 or 2 channels. Page All Available allows the ability to (*) This feature does NOT interrupt ongoing communications.
  • Page 76 Application Example 1 Application Example 2 An employee in a retail shop uses a DLR1060 Anna needs to talk privately to another user (6 channel radio) with the Top Button (John) and she is not sure in which channel to programmed to Private Reply and Channel 6 find him.

  • Page 77: How Page All Available Works

    How Page All Available works All users in Channel 3 and 4 are available (nobody is transmitting). Talking User B and C busy in Private Call Talking CHANNEL 4 AVAILABLE Listening CHANNEL 3 CHANNEL 2 AVAILABLE BUSY English...
  • Page 78 User D in Channel 3 initiates Page All Available by switching to Channel 6(*). “Page All Available” Talking User B and C busy in Private Call Talking CHANNEL 4 AVAILABLE All users in Channel 3 and 4 are AVAILABLE Listening (Nobody is transmitting).
  • Page 79 All users from Channel 3 and 4 are brought into a temporary “super group”. User D then presses the PTT button and starts talking to all available users in both channels. Talking User B and C busy in Private Call Talking CHANNEL 4 LISTENING TO USER D...
  • Page 80 User D continues talking to all available users. User E wants to reply to user D and presses the Top button(*). User E goes in queue for Private Reply. “Private Reply” Talking User B and C busy in Private Call Talking Listening CHANNEL 4...
  • Page 81 Once user D stops transmitting by releasing the PTT button, the Page All Available is over. All users in Channel 3 and 4 are back to their original channel groups. User E remains in queue for Private Reply. Talking User B and C busy in Private Call Talking...
  • Page 82 User E presses PTT to talk to user D. They are now engaged in a Private Conversation. Nobody else can hear them. The Top Button LED indicator for radio D and E illuminates solid orange. Talking User B and C busy in Private Call Private call in progress...
  • Page 83 Once User D and E finish the private conversation, they are returned to their respective group channel. The Top Button LED indicator both radios switched off. Talking User B and C busy in Private Call Talking Listening CHANNEL 4 AVAILABLE CHANNEL 3 AVAILABLE CHANNEL 2...

  • Page 84: Page All Available Status Indicator

    Page All Available Status Indicator Note: To initiate Page All Available, press the Top Button or change to a channel that is preset to Page All Available followed by the PTT button to talk to all available users in different channels. Table 4: Page All Available Status Indicator Page All Available Status Top Button LED Indicator...

  • Page 85: Customer Programming Software

    To program, connect the DLR Series radio via CUSTOMER the Drop-in Charger Tray and CPS PROGRAMMING Programming Cable to your computer as SOFTWARE (CPS) shown in the picture above. Prior to programming, verify that the switch in the Programming Cable is in the ‘Digital(**)’ position.

  • Page 86: Cps Basic Menu Instructions

    CPS BASIC MENU INSTRUCTIONS Click “New Profile” to create customized profile based on the default profile. Open the CPS software and click on the “RADIO” top tab. Click on the “READ” tab to read the radio(*), or On the drop down menu “Radio Type”, select “DLR”...
  • Page 87 Scroll down to see more feature options. Customize as necessary. Click ONLY if you are going to upload radios IDs for Direct Call, Private Groups or interoperability with DTR radios. Scroll down for more feature options English...
  • Page 88 You can choose which options you want to be available in the Advanced Configuration Mode. You can add any of the features shown to be accessed by the radio Channel / Menu button in the radio basic operation mode. You can also choose which function you want to have for ON / OFF button short press. Selection of options to be available in the Advanced Configuration mode.
  • Page 89 You can modify the radio Top Button feature by changing the default option. Programmable features to the radio basic menu (Channel / Menu button). List of programmable features for the Top Button. English...
  • Page 90 In order to enable Direct Call feature in your Basic Menu options, you need to first upload the radio(s) unique “private” identification (12 digit) number. Click on the “Switch to ADVANCED” button. Under “Privates (Advanced)” tab, click “Add” for CPS to upload radio ID. You can customize the radio ID name under the Name column.
  • Page 91 Customize your PROFILE ID Number for any 4 digit number different from “0000” to differentiate your radios in a radio fleet. Home Channel is OFF by default. If you want to assign a specific channel as your Home Channel, select the channel using the drop down menu under “Home Channel”.
  • Page 92 Upon setting your Home Channel, CPS will enable the option to set the Home Channel Mode. Select the mode using the drop down menu under “Home Channel Mode”. List of available modes for Home Channel Customize the name of your channel (alias) by typing in each one of the channel boxes. English...
  • Page 93 11a. You can also set your own customized Channels Voice Prompt (VP) in order to enable your channel name to be announced by the radio. Click on “Edit More” to edit the voice prompt. English...
  • Page 94 11b. After clicking “Edit More”, you will be brought into a different menu to customize your channel name. Select the checkbox “Enable User Customized VP” to enable the standard Voice Prompt. When there is a speaker icon in the menu, then that channel has customized voice prompt enabled. Click on the speaker icon to preview the User Customized VP.
  • Page 95 Once you have changed all the settings, click “Write to radio” in order to program your radio with the new settings. The CPS will display a window confirming the writing (programming of your radio) is successful. You can also save your profile at any time in order to use the same settings when programming other radios by clicking on “Save to profile”.
  • Page 96 Notes English...

  • Page 97: Cloning

    CLONING CLONING RADIOS You can clone DLR Series radio profiles from one Source radio to a Target radio by using any one of these 4 methods: • Using a Multi Unit Charger (MUC- optional accessory), • Using two Single Unit Chargers (SUC) and a Radio-to-Radio cloning cable (optional accessory), •...

  • Page 98: Cloning Mode

    Cloning Mode In order to set your radios into Cloning Mode, power UP using the ON / OFF button while pressing the PTT and (-) buttons simultaneously. Radio sounds cloning mode beeps followed by the voice prompt “Cloning Mode, Serial”. ON / OFF Button (-) Button Power UP using the ON /...

  • Page 99: Cloning With A Multi-Unit Charger (Muc) (Optional Accessory)

    Cloning with a Multi-Unit Charger (MUC) • 1 and 2, (Optional Accessory) • 4 and 5, • 7 and 8, or Pocket 5 • 10 and 11. Pocket 4 “CLONE” symbol When cloning, the MUC does not need to be Pocket 2 Pocket 1 plugged into a power source, but ALL radios...

  • Page 100: Cloning Radio Using The Radio To Radio (R2R) Cloning Cable (Optional Accessory)

    Before starting the cloning process, make sure • MUC pockets numbers should be read from left to you have: right with the Motorola logo facing front. • A Cloning Cable (P/N# HKKN4028_) • A fully charged battery in each of the radios.
  • Page 101 cables) from the SUCs. Once the cloning process is completed, turn the Radios OFF and ON or, long press the PTT Plug one side of the cloning cable mini USB button to exit the ‘cloning’ mode connector to the first SUC and the other end to the second SUC.

  • Page 102: Wireless Profile Id Number Cloning

    Note: This cloning cable is designed to operate PROFILE ID helps to preserve each user radio only with compatible Motorola SUC set up but still make sure all radios are under PMLN7140_. the same PROFILE ID Number. It is also useful...
  • Page 103 • Press and release the (-) button and the Source Radio will announce “Wireless”. Power the Target radio following the sequence below: • Press the PTT button and the (-) button simultaneously while turning the radio • Wait for 3 seconds before releasing the buttons until the audible tone and voice announcement “Clone Mode Serial”...

  • Page 104: Cloning Mode Status Indicator

    CLONING MODE STATUS INDICATOR To enter cloning mode, press and hold both the PTT button and (-) button at the same time, while turning ON the radio. Table 1: Cloning Mode Status Indicator Cloning Mode Status LED Indicator Voice Prompt or Tone Cloning Mode (by default is Serial) Double Blink Red “Clone Mode, Serial”...

  • Page 105: Troubleshooting

    TROUBLESHOOTING Symptom Try This... Recharge or replace the Li-Ion battery. No Power Extreme operating temperatures may affect battery life. Refer to “About the Li-Ion Battery” on page 12 Make sure that one side of the programming cable is connected to the radio and the other side of the programming cable is connected to the USB port.
  • Page 106 Symptom Try This... If you hear conversations from other users that don't belong to your radio fleet, Hearing conversation from it means your radios are set up with the same Profile ID as your neighbors. Very other users that are not within likely both of you have the radios in the default Profile ID Number "0000".
  • Page 107 Symptom Try This... When talking on the radio, make sure not to release the PTT button at any moment. Whether you are using the PTT button on the radio or using an in-line PTT in an earpiece accessory, always press the PTT button firmly until the While talking on the radio, a transmission is finished.
  • Page 108 Symptom Try This... All radios produce a strong voice / audio feedback if they are too close to each other and their volume is set too high. Lower the volume in your radio. Using earpieces can also help reduce aduio feedback if radios are too close. Radio echo feedback Important:: Make sure the radios are OFF before charging them.
  • Page 109 Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check to see if the radio has been programmed using the CPS with a customized profile. For questions or comments related to this product, please contact Motorola 1-800-448-6866 or visit us at www.motorolasolutions.com/DLR.

  • Page 110: Use And Care

    USE AND CARE Do not use alcohol or Do not immerse in water Use a soft damp cloth to cleaning solutions clean the exterior If the radio is submerged in water... Turn radio OFF and Dry with soft cloth Do not use radio until remove batteries completely dry English...

  • Page 111: Motorola Limited Warranty For The United States And Canada

    This limited warranty is a consumer's exclusive Repaired or Replaced. to the consumer, whichever is longer. remedy, and applies as follows to new Motorola Products, Accessories and Software purchased by consumers in the United States, which are accompanied by this written warranty.
  • Page 112 (c) use of the Products or Accessories for nonconforming or non-Motorola housings, or commercial purposes or subjecting the Product or parts, are excluded form coverage. Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage. English...
  • Page 113 Accordingly, any copyrighted software third parties, that the operation of the software contained in the Motorola products may not be products will be uninterrupted or error free, or that modified, reverse-engineered, distributed, or...
  • Page 114 United States of America. The any license under the copyrights, patents, or Governments of the United States of America may patent applications of Motorola or any third party restrict the exportation or re-exportation of this software provider, except for the normal, non- product to certain destinations.

  • Page 115: Accessories

    BATTERY ACCESSORIES Part No. Description AUDIO ACCESSORIES HKNN4013_ Li-Ion Battery 1800mAh Part No. Description CABLES HKLN4599_ Earpiece w/PTT, Mic, Slim Plug Part No. Description Surveillance Earpiece w/PTT, HKLN4601_ Slim Plug HKKN4027_ Business Radio CPS Cable Kit Swivel Earpiece w/PTT, Slim HKLN4604_ Plug Business Radio Cloning Cable...

  • Page 116: Carry Accessories

    CARRY ACCESSORIES Part No. Description HKLN4615_ DLR Swivel Clip Holster Kit English...
  • Page 118 Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2015 Motorola Solutions, Inc.

This manual is also suitable for:

Dlr1060

Table of Contents