Extern Midi A/B Prog Change; Extern Menu - Clavia NordStage2 EX 88 User Manual

Extern Menu

Hold Shift and press Program 4/Extern to access the Extern menu,
where you can find settings and functions relating to the Extern section.
Use the Page 3 and 4buttons to navigate between the various menu
items on the menu and use the Value Dial to change settings. When
you are done, press Exit (Shift) to exit the menu.
M Most items on the Extern menu have separate entries for Slot A
and B.
M
Most settings from the Extern menu are saved with a Program.
The only exceptions are the "Extern MIDI A/B Channel" if Extern
MIDI Mode is set to Global, and the "Send on Load" function
which always is global.
Extern MIDI Mode
The Extern MIDI Channel can be set in two different manners, either
globally, or independently for each program. When "Global" is selected,
the Extern MIDI A & B channels will be the same for all programs. If
program is selected, the Extern MIDI A & B channel setting will be
saved with each Stage 2 EX program.
Range: Global, Program (default)
Extern MIDI A/B Channel
This sets the Extern section's transmitting MIDI channels.
Range: MIDI 1-16 (MIDI 14 default for Slot A, MIDI 15 is default for
Slot B), USB1 - USB16,
Extern MIDI A/B Volume
The Extern section can send MIDI Volume messages (0-127), allowing
you to control the level of an external device.
Range: Off (Default), 0-127

Extern MIDI A/B Prog Change

The Extern section can transmit MIDI program Change messages (0-
127), allowing you to change programs on external devices.
Range: Off (Default), 1-128
Extern MIDI A/B Bank Sel cc 00
This allows you to set a value for a MIDI Bank Select message on
Control Change address 00 (cc 00).
Range: Off, 0-127
Extern MIDI A/B Bank Sel cc 32
This allows you to set a value for a MIDI Bank Select message on
Control Change address 32 (cc 32).
M There are many different variations between instruments in how
Banks are numbered and accessed via MIDI. Please consult your
other unit's manual.
Range: Off (Default), 0-127
Extern MIDI A/B CC Number
This decides which MIDI Controller number the Extern section should
be transmitted when MIDI CC is activated.
Range: MIDI CC 0-119 (Default is 2)
Extern MIDI A/B CC Value
This will transmit values for the selected MIDI CC number.
Range: Off (Default), 1-127
Extern MIDI A/B Send Wheel
This setting toggles if the Modulation Wheel should transmit Mod
Wheel MIDI data (CC 1) or not.
Range: Yes (Default), No
Extern MIDI A/B Send A.Touch
This setting toggles if After Touch should transmit Channel Touch MIDI
data or not.
Range: Yes (Default), No
Extern MIDI A/B Send CtrlPed
This setting toggles if a control pedal connected to the CTRL Pedal
input should transmit Expression MIDI data (CC 11) or not.
Range: Yes (Default), No
Extern MIDI A/B Send Swell
This setting toggles if a control pedal connected to the Swell Pedal
input should transmit Foot Controller MIDI data (CC 4) or not.
Range: Yes (Default), No
Extern MIDI A/B Vel Curve
Use this setting to adjust the velocity response curves that applies to
the Extern section.
Range: Soft , Norm, Hard
Extern MIDI Send on Load
This setting toggles if any settings for the Program Change, Volume
or MIDI CC messages in the Extern section should be automatically
transmitted when a Program is selected, or not.
Range: Off (Default), On
Extern MIDI Soft Thru
Incoming MIDI that matches the Global or Slot A/B channels can be
re-routed on the Extern channel to the MIDI OUT jack or the USB inter-
face, if the Extern section is active on the current Program. This setting
determines if this re-routing should apply or not.
Range: Off (Default), On
Chapter 11 MeNUS | 45