Table of Contents
Advertisement
FRESH AIR FOR
COMBUSTION AND
VENTILATION
WARNING:
If the area in
which the heater may be operated
d o e s n o t m e e t t h e r e q u i r e d
volume for indoor combustion air,
combustion and ventilation air
shall be provided by one of the
methods described in the National
F u e l
G a s
C o d e ,
Z 2 2 3 . 1 / N F P A
International Fuel Gas Code, or
a p p l i c a b l e
l o c a l
PROVIDING ADEQUATE
VENTILATION
All spaces in homes fall into one of
the three following ventilation clas-
sifications:
1.
Unusually Tight Construction
2.
Unconfined Space
3.
Confined Space
The information on pages 4
through 6 will help you classify
your space and provide adequate
ventilation.
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if you Have a Confined or Unconfined Space*
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (length
×
×
Length
Width
Height=
Example: Space size18ft.(length)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space)
Example: 2304 cu. ft. (volume of space)
WARNING: If the area in which the heater may be operated is smaller than that defined as an
unconfined space or if the building is of unusually tight construction, provide adequate combustion and
ventilation air by one of the methods described in the National Fuel Gas Coda, ANS Z223.1, Section 5.3
or applicable local codes.
Unusually Tight Construction
The air that leaks around doors
and windows may provide enough
fresh air for combustion and ventilation.
However, in buildings of unusually
tight construction, you must provide
additional fresh air.
Unusually
defined as construction where:
a.
walls and ceilings exposed to
the outside
continuous
with a rating of one perm (6
A N S I
kg per pa-sec-m
5 4 ,
t h e
openings gasketed or sealed and
b. weather
c o d e s .
added on openable windows and
doors and
c. caulking or sealants are applied to
areas such as joints around
dow and door frames, between sole
plates and floors, between
ceiling joints, between wall panels, at
penetrations for plumbing, electrical,
and gas lines, and at
ings. If your home meets all of
the three criteria above, you must
provide additional fresh air. See
Ventilation Air From Outdoors,
pages 5 and 6. If your home does
not meet all of the three criteria
above, see
Flow for Heater Location, page 4, 5.
cu.ft. (volume of space)
×
16ft.( width)
50 cu. ft.=(Maximum Btu/Hr the space can support)
÷
50 cu.ft.=46.1 or 46.100(maximum Btu/Hr the space can support)
÷
tight construction is
atmosphere
have
water
vapor
retarder
)
or less with
2
stripping
has
other open-
Determining Fresh-Air
×
×
width
height).
×
8ft. (ceiling height)=23040cu. ft. (volume of space)
4
Confined and
Unconfined Space
Confined space is a space whose
volume is less than 50 cubic feet
per 1,000 Btu per hour (4.8 m
kw) of the aggregate input rating
of all appliances installed in that
space and an unconfined space
as a space whose volume is not
less than 50 cubic feet per 1,000
a
Btu per hour (4.8 m
the aggregate input rating of all
×
10
-11
appliances installed in that space.
Rooms communicating directly
with the space in which the
been
appliances are installed*, through
openings not furnished with
doors, are considered a part of
the unconfined space.
win-
This heater shall not be in-
stalled
in a confined space or
wall-
unusually tight construction unless
provisions are provided for
adequate
combustion
ventilation air.
*
A d j o i n i n g
communicating only
are doorless passageways or
ventilation grills between them.
per
3
per kw) of
3
and
r o o m s
a r e
if
there
Advertisement
Table of Contents
