Related Manuals for Toro CCR 2450 GTS Series
Summary of Contents for Toro CCR 2450 GTS Series
- Page 1 Form No. 3326-125 Rev A CCR 2450 GTS CCR 3650 GTS Snowthrower Model No. 38515—220000001 and Up Model No. 38516—220000001 and Up Model No. 38517—220000001 and Up Model No. 38518—220000001 and Up Operator’s Manual Domestic English (EN)
-
Page 2: Table Of Contents
........Dealer or Toro Customer Service and have the model and Safe Operating Practices . -
Page 3: Safety
Toro. engine is ever started. Let the engine and the snowthrower adjust to the This is the safety alert symbol. It is used to alert you outdoor temperature before starting to clear snow. -
Page 4: Toro Snowthrower Safety
Maintain or replace safety and instruction labels when necessary. Toro Snowthrower Safety The following list contains safety information specific to Toro products or other safety information that you must know. -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 60-9480 105-3521 (Model 38515) or 105-1955 (Model 38517) 61-4790 (Electric-start models only) 104-2767 105-3523 (Model 38516) or 105-1954 (Model 38518) - Page 6 CYLINDREE (CC) : 141 Pour plus de détails sur la sécurité, l’entretien et les réglages, reportez-vous au manuel de l’utilisateur. Nº de téléphone des services de vente et d’après-vente aux Etats-Unis : 1-800-526-6937 The Toro Company Bloomington, MN INFORMATION IMPORTANTE CONCERNANT LE MOTEUR...
-
Page 7: Assembly
Assembly Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts DESCRIPTION QTY. Knob Installing the handle (Models 38517 and 38518 Curved washer only) Handle lock Screws Locknuts Washers Installing the discharge chute Discharge chute Chute handle (Models 38515 and 38516 only) Bolts... -
Page 8: Installing The Handle
Installing the Handle Models 38517 and 38518 1. Cut the plastic tie that secures the control cable to the handle (Fig. 6). Figure 4 4. Insert the loose end of the control cable into the bottom hole in the control bar (Fig. 5). Figure 6 1. -
Page 9: Installing The Discharge Chute
Installing the Discharge Chute Models 38515 and 38516 1. Place the discharge chute over the chute ring, and align the hole in the back of the discharge chute with the center hole in the chute ring (Fig. 10). Figure 8 4. -
Page 10: Installing The Chute Crank
Models 38517 and 38518 Installing the Chute Crank 1. Place the discharge chute over the chute ring, and align Models 38517 and 38518 the hole in the back of the discharge chute with the center hole in the chute ring (Fig. 11). 1. -
Page 11: Before Starting
Oil below 32 F (0 C) requires additional mixing. away from an open flame or where a spark may 2. Add the full amount of Toro 50:1 2-Cycle Oil (Fuel ignite the gasoline fumes. Stabilizer Added) or an equivalent high grade, NMMA... -
Page 12: Filling The Fuel Tank
3. Install the cap on the fuel container. 4. Shake the container to mix the gasoline and oil thoroughly. 5. Slowly remove the cap and add the remaining amount of gasoline. Filling the Fuel Tank Important Do not overfill the fuel tank. The gasoline-and-oil mixture must have room to expand. -
Page 13: Stopping The Engine
Adjusting the Discharge Chute Caution Models 38515 and 38516 If you leave the snowthrower plugged into a power Move the chute handle left and right to adjust the direction outlet, someone can inadvertently start the of the snow stream (Fig. 14). The chute deflector handle on snowthrower and injure people or damage top of the discharge chute controls the height of the snow property. -
Page 14: Snowthrowing Tips
In snowy and cold conditions, some controls and moving parts may freeze. Do not use excessive force when trying to operate frozen controls. If you have difficulty operating any control or part, start the engine and let it run for a few minutes. After clearing the snow, let the engine run for a few minutes to prevent moving parts from freezing. -
Page 15: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Check the control cable both initially and after the first hour of operation; adjust it if necessary. Refer to Adjusting the Control Cable on page 16. Initially Check for loose fasteners and tighten them if necessary. -
Page 16: Adjusting The Control Cable
Adjusting the Control Cable Important The control cable must contain slack when you disengage the control bar for the rotor blades to stop Check the control cable for proper adjustment initially, properly. after the first operating hour, and then annually thereafter. Adjusting the Cable Checking the Cable For Models 38515 and 38516 only:... -
Page 17: Replacing The Rotor Blades
For Models 38517 and 38518: drive system. To remove moisture, start the rotor and operate it without a load for 30 seconds. Once you remove 1. Unhook the upper cable end from the hole in the control the moisture, the drive belt should not slip. bar (Fig. -
Page 18: Removing The Old Rotor Blades
Removing the Old Rotor Blades 1. Remove the 4 torx screws and the 4 locknuts that secure the outer edges of the rotor blade to the rotor assembly (Fig. 21). m-5538a/m-5059 Figure 22 1. Thick rubber side 3. Thin rubber side 2. -
Page 19: Replacing The Scraper
Replacing the Scraper Note: If the rotor blades are partially or completely worn, replace the rotor blades when you replace the scraper. This ensures proper snowthrower operation and performance. 1. Stop the engine and wait for all moving parts to stop. m-5061a 2. -
Page 20: Replacing The Drive Belt
5. Pull up on the idler pulley and remove the old drive belt from the rotor pulley, the brake arm assembly, and the engine pulley (Fig. 28). m-3215 Figure 26 1. 0.030 in. (0.76 mm) 10. Install the spark plug by hand and then torque it to 15 ft-lb (20.4 N m). -
Page 21: Storage
Preparing the Fuel System 1. Add a fuel stabilizer/conditioner to the fuel in the fuel tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel m-5537 stabilizer/conditioner. -
Page 22: Troubleshooting
Troubleshooting Toro designed and built your snowthrower for trouble-free operation. Check the following components and items carefully, and refer to Maintenance on page 15 for more information. If a problem continues, contact an Authorized Service Dealer. Problem Possible Causes Corrective Action Electric starter does not turn 1. - Page 23 Problem Possible Causes Corrective Action Engine runs, but the snowthrower 1. You are walking too fast or too 1. Change your walking speed. discharges snow poorly or not at slow. 2. You are trying to remove too 2. Reduce the amount of snow much snow per swath.
-
Page 24: Federal Emission Control Warranty Statement
If you have any questions regarding your warranty rights and – EGR valve body and piping system connecting to the responsibilities, or if you need a referral to a Toro Service Dealer, intake side of the engine please feel free to contact us at: –... - Page 25 Service Dealer or Master Service Dealer. The Yellow Pages of your with the use of the Toro Products covered by this warranty, except telephone directory is a good reference source. The dealer will...
-
Page 26: The Toro Starting Guarantee
– failure to follow proper maintenance procedures your Toro Engine will start on the first or second pull for five years – rotary mower blade or snowthrower auger/paddles striking from the date of purchase—if you provide the routine maintenance an object it requires—or we will fix it free of charge. - Page 27 Date Hours Air Cleaner Change Oil Lubricate Wheels Check Spark Storage Used Service (does not apply (mowers only) Plug Preparation (mowers only) to two-cycle) Part No. 374-0018 Rev. C...
-
Page 28: The Toro Total Coverage Guarantee
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.