3. TECHNICAL BRIEF 3. TECHNICAL BRIEF 3.1 General Description The KS10 supports UMTS-2100 DS-WCDMA, EGSM-900, DCS-1800, and PCS-1900. All receivers and the UMTS transmitter use the radio One Zero-IF architecture to eliminate intermediate frequencies, directly converting signals between RF and baseband. The EGSM, DCS1800 and PCS1900 transmitters use a baseband-to-IF up-conversion followed by an offset phase-locked loop that translates the GMSK-modulated signal to RF.
3. TECHNICAL BRIEF A generic, high-level functional block diagram of KS10 is shown in Figure 1-1. One antenna collects base station forward link signals and radiates handset reverse link signals. The antenna connects with receive and transmit paths through a switch module (plus a duplexer for UMTS-2100 operation).
3.2 GSM Mode 3.2.1 GSM Receiver The Dual-mode KS10’s receiver functions are split between the two RFICs as follows: • UMTS-2100 operation uses the RFR6250 Receiver ICs to implement the receive signal path, accepting an RF input and delivering analog baseband outputs (I and Q).
AC-couple the inactive pin to ground using an appropriately valued capacitor (12 pF is used in KS10). The 27 pF capacitor should be used to AC-couple the active pin to the VCO signal. Using only the selected VCO signal, the RFR6250 IC LO generation and distribution circuits create the necessary LO signals for the active quadrature downconverter.
A UMTS duplexer splits a single operating band into receive and transmit paths. Important performance requirements include: - Insertion loss . this component is also in the receive and transmit paths; In the KS10 typical losses: UMTS Tx = 1.45 dB, UMTS Rx = 1.86 dB.
Its detector coupling range and converted voltage is based on diode sensitivity and transmitter power level. The KS10 uses National Semiconductor ADL5500 power detector IC. In Figure 1.5.5-1, C580 is set to 47ohm&Coupler resulting in an attenuation of 31.4dB. The output voltage is proportional to the logarithm of the input power.
3.9.1. Keypad KS10 has 28 buttons, 12 function keys in Sub PCB (Folder), 12 numeric keys in main and 4 side keys. KS10 use key coder IC because Stn8810 has not enough GPIO. Key coder IC use interrupt and I2C interface for communication with STn8810.
Specification, Revision 2.0. The USB Specification Revision 1.1 defines two speeds of operation, namely low-speed (1.5 Mbps) and full-speed (12 Mbps), both of which are supported by the MSM6275. KS10’s USB interface uses the PM6650 internal logic for USB Transceiver. Name...
3. TECHNICAL BRIEF 3.14. Camera interface KS10 has two cameras : 2M Pixel CMOS and VGA Pixel CMOS Camera Below figures shows the camera board to board connector and camera I/F signal. 3.14.1. Mega Camera Interface CCIRID(3)_CAM INOUT_A4 INOUT_B4 CCIRID(3)
3. TECHNICAL BRIEF 3.15 Bluetooth KS10 supported bluetooth, which is possible to data file transfer, BT headset call. CPU (STn8810) interfaces with bluetooth one chip module (U401) which includes RF and baseband. The STLC2500C is a single chip ROM-based Bluetooth solution for applications requiring integration up to HCI level.
4.8 USB trouble USB Initial sequence of KS10 is : USB connected to KS10 → USB_VBUS_IN(VA205) go to 5V → USB_VBUS_EN go to high (Q702 Pin_2) → USB_VBUS(D701) go to 5V → USB_D+(VA202) go to 3.3V → 48M Crystal on → USB_DATA is triggered → USB work...
4. TROUBLE SHOOTING 4.16 Camera trouble Camera control signals are generated by STN8810 and directly connected with STN8810. KS10 has two cameras. The one is a 2 Mega Camera, the other is VGA camera. 2M START Check the camera conn. and...
5. DOWNLOAD 5.4 KS10 LGDP2 run file & DLL file setup 5.4.1 Setup the KS10 run file & DLL file. 5.4.1.1 Copy "LGDP2_V32" file & 5.4.1.2 And then paste these file & folder "Model" folder in "LGDP2_for set- on "DOWNLOAD" folder in C up"...
Page 165
5. DOWNLOAD 5.5.8 Choose the "KS10.DLL" file on "Model" folder in "Download" folder. 5.5.9 Click “Run Download Configuration” button. 5.5.10 Select AP download & Old Version Binary & MP Download icons. Explain Old Version Binary icon It is control "Binary" type.