HP EliteDesk 705 G1 Hardware Reference Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. EliteDesk 705 G1
  6. Hardware reference manual

HP EliteDesk 705 G1 Hardware Reference Manual

Elitedesk 705 g1 small form factor
Hide thumbs Also See for EliteDesk 705 G1:
Table of Contents

Advertisement

Quick Links

See also: Maintenance and Service Manual
Hardware Reference Guide
HP EliteDesk 705 G1 Small Form Factor

Advertisement

Table of Contents
loading

Related Manuals for HP EliteDesk 705 G1

Summary of Contents for HP EliteDesk 705 G1

  • Page 1 Hardware Reference Guide HP EliteDesk 705 G1 Small Form Factor...
  • Page 2 HP End User Not all features are available in all editions License Agreement (EULA). If you do not The information contained herein is subject of Windows 8.

  • Page 3: About This Book

    About This Book This guide provides basic information for upgrading the HP EliteDesk Business PC. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
  • Page 4 About This Book...

  • Page 5: Table Of Contents

    Removing and replacing a 3.5-inch hard drive ..............32 Removing a 2.5-inch hard drive ..................35 Installing a 2.5-inch hard drive ................... 37 Installing a security lock ........................40 Cable lock .......................... 40 Padlock ..........................40 HP Business PC Security Lock ..................41...
  • Page 6 Front bezel security ......................45 Appendix A Battery replacement ........................47 Appendix B Electrostatic discharge ........................50 Preventing electrostatic damage ......................50 Grounding methods ..........................50 Appendix C Computer operating guidelines, routine care and shipping preparation ......... 51 Computer operating guidelines and routine care ................51 Optical drive precautions ........................

  • Page 7: Product Features

    Standard configuration features Features may vary depending on the model. For support assistance and to learn more about the hardware and software installed on your computer model, run the HP Support Assistant utility. NOTE: This computer model can be used in a tower orientation or a desktop orientation.

  • Page 8: Front Panel Components

    Front panel components Drive configuration may vary by model. Some models have a bezel blank covering one or more drive bays. Slim Optical Drive (optional) Headphone Connector USB 2.0 Port - Charging (black) Dual-State Power Button USB 2.0 Port (black) Hard Drive Activity Light USB 3.0 Ports (blue) 3.5-inch Media Card Reader (optional)

  • Page 9: Rear Panel Components

    Power Cord Connector NOTE: An optional second serial port and an optional parallel port are available from HP. When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use the connector for a line-in device or a microphone.

  • Page 10: Media Card Reader Components

    Media card reader components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Slot Media SD/HC/XC/UHS-I/II Secure Digital (SD) Secure Digital High Secure Digital ●...

  • Page 11: Serial Number Location

    Serial number location Each computer has a unique serial number and a product ID number that are located on the exterior of the computer. Keep these numbers available for use when contacting customer service for assistance. Serial number location...

  • Page 12: Hardware Upgrades

    To reduce the risk of serious injury, read the . It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside.

  • Page 13: Removing The Computer Access Panel

    Removing the computer access panel To access internal components, you must remove the access panel: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 14: Replacing The Computer Access Panel

    Replacing the computer access panel Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit so that it locks into place (2). Chapter 2 Hardware upgrades...

  • Page 15: Removing The Front Bezel

    Removing the front bezel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 16: Removing Bezel Blanks

    (4). NOTE: After removing the slim optical drive bezel blank and installing a slim optical drive, you can install an optional bezel trim piece (available from HP) that surrounds the front of the slim optical drive. Chapter 2 Hardware upgrades...

  • Page 17: Replacing The Front Bezel

    Replacing the front bezel Insert the four hooks on the bottom edge of the bezel into the rectangular holes on the chassis (1) then rotate the top side of the bezel onto the chassis (2) and snap it into place. Replacing the front bezel...

  • Page 18: Changing From Desktop To Tower Configuration

    Orient the computer so that its right side is facing down and place the computer in the optional stand. NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower stand. Reconnect the power cord and any external devices, then turn on the computer.

  • Page 19: System Board Connections

    System board connections Refer to the following illustration and table to identify the system board connectors for your model. System Board Connector System Board Label Color Component PCI Express x16 downshifted X4PCIEXP white Expansion Card to a x4 PCI Express x1 X1PCIEXP2 black Expansion Card...

  • Page 20: Installing Additional Memory

    Installing additional memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3- SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM.

  • Page 21: Installing Dimms

    The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is ● not equal to the total memory capacity of the DIMMs in Channel B. In flex mode, the channel populated with the least amount of memory describes the total amount of memory assigned to dual channel and the remainder is assigned to single channel.
  • Page 22 Open both latches of the memory module socket (1), and insert the memory module into the socket (2). NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. Populate the black DIMM sockets before the white DIMM sockets.

  • Page 23: Removing Or Installing An Expansion Card

    Removing or installing an expansion card The computer has two PCI Express x1 expansion slots, one PCI Express x16 expansion slot, and one PCI Express x16 expansion slot that is downshifted to a x4 slot. NOTE: The PCI Express slots support only low profile cards. You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 slot.
  • Page 24 If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. If you are removing a PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket.
  • Page 25 If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame.
  • Page 26 To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the chassis (1) so that the bracket on the card is aligned with the open slot on the rear of the chassis. Press the card straight down into the expansion socket on the system board (2).

  • Page 27: Drive Positions

    Drive positions Slim optical drive bay 3.5-inch internal hard drive bay 3.5-inch drive bay for optional drives (media card reader shown) 2.5-inch internal hard drive bay NOTE: The drive configuration on your computer may be different than the drive configuration shown above. To verify the type and size of the storage devices installed in the computer, run Computer Setup.

  • Page 28: Installing And Removing Drives

    You must install guide screws to ensure the drive will line up correctly in the drive cage and lock ● in place. HP has provided four extra 6-32 standard guide screws installed on the top of the drive bay. The 6-32 standard guide screws are required for a media card reader or a secondary hard drive installed in the 3.5-inch optional drive bay.
  • Page 29 CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode.

  • Page 30: Removing A 3.5-Inch Device

    Removing a 3.5-inch device CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices.
  • Page 31 Disconnect the drive cables from the rear of the drive, or, if you are removing a media card reader, disconnect the USB cable from the system board as indicated in the following illustration. Press inward on the release lever at the rear of the drive (1) and slide the drive out of the rear of the drive bay (2).

  • Page 32: Installing A 3.5-Inch Device

    Install 6-32 guide screws in the holes on each side of the drive. NOTE: HP has supplied four extra 6-32 guide screws on top of the drive cage. Refer to Installing and removing drives on page 22 for an illustration of the location of the extra guide screws.
  • Page 33 Rotate the drive cage to its upright position. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. Installing and removing drives...
  • Page 34 If installing a USB 3.0 media card reader, you must use the USB 3.0 to USB 2.0 adapter (1) and connect the adapter cable from the media card reader to the USB 2.0 connector on the system board labeled MEDIA (2). NOTE: Refer to System board connections on page 13...

  • Page 35: Removing A Slim Optical Drive

    Removing a slim optical drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices.

  • Page 36: Installing A Slim Optical Drive

    Installing a slim optical drive Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.
  • Page 37 NOTE: An optional bezel trim piece that surrounds the front of the optical drive is available from HP. Install the bezel trim piece in the front bezel before installing the front bezel. Replace the computer access panel. If the computer was on a stand, replace the stand.

  • Page 38: Removing And Replacing A 3.5-Inch Hard Drive

    Removing and replacing a 3.5-inch hard drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer.
  • Page 39 Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out, slide the drive back until it stops, then lift the drive up and out of the bay (2). To install a 3.5-inch hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive.
  • Page 40 Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it forward until it stops and locks in place. Connect the power cable (1) and data cable (2) to the back of the hard drive. NOTE: The data cable for the primary hard drive must be connected to the dark blue connector labeled SATA0 on the system board to avoid any hard drive performance problems.

  • Page 41: Removing A 2.5-Inch Hard Drive

    Removing a 2.5-inch hard drive Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.
  • Page 42 Disconnect the power cable (1) and data cable (2) from the back of the hard drive. Pull outward on the release lever at the rear of the drive (1) then slide the drive back until it stops and pull it down and out of the drive bay (2). Chapter 2 Hardware upgrades...

  • Page 43: Installing A 2.5-Inch Hard Drive

    Installing a 2.5-inch hard drive Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.
  • Page 44 Align the guide screws on the drive with the J-slots on the sides of the drive bay. Press the drive up into the drive bay then slide it forward until it locks in place. Connect the power cable (1) and data cable (2) to the back of the hard drive. NOTE: If the 2.5-inch hard drive is the primary drive, connect the data cable to the dark blue SATA connector labeled SATA0 on the system board.
  • Page 45 Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down. Replace the computer access panel. If the computer was on a stand, replace the stand. Reconnect the power cord and any external devices, then turn on the computer.

  • Page 46: Installing A Security Lock

    Installing a security lock The security locks displayed below and on the following pages can be used to secure the computer. Cable lock Padlock Chapter 2 Hardware upgrades...

  • Page 47: Hp Business Pc Security Lock

    HP Business PC Security Lock Fasten the security cable by looping it around a stationary object. Insert the cable lock into the cable lock slot on the back of the monitor and secure the lock to the monitor by inserting the key into the key hole on the rear of the lock and rotating the key 90 degrees.
  • Page 48 Slide the security cable through the hole in the cable lock on the rear of the monitor. Use the bracket provided in the kit to secure other peripheral devices by laying the device cable across the center of the bracket (1) and inserting the security cable through one of the two holes in the bracket (2).
  • Page 49 Thread the keyboard and mouse cables through the computer chassis lock. Screw the lock to the chassis in the thumbscrew hole using the screw provided. Installing a security lock...
  • Page 50 Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lock. When you have completed all steps, all of the devices at your workstation will be secured. Chapter 2 Hardware upgrades...

  • Page 51: Front Bezel Security

    Front bezel security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer.
  • Page 52 Install the security screw through the middle front bezel release tab to secure the front bezel in place. Replace the access panel. If the computer was on a stand, replace the stand. Reconnect the power cord and turn on the computer. Lock any security devices that were disengaged when the access panel was removed.

  • Page 53: Appendix A Battery Replacement

    The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/...
  • Page 54 Slide the replacement battery into position, positive side up. The battery holder automatically secures the battery in the proper position. Type 2 To release the battery from its holder, squeeze the metal clamp that extends above one edge of the battery. When the battery pops up, lift it out (1). To insert the new battery, slide one edge of the replacement battery under the lip of the holder with the positive side up.
  • Page 55 Insert the new battery and position the clip back into place. NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the computer access panel. Plug in the computer and turn on power to the computer. Reset the date and time, your passwords, and any special system setups using Computer Setup.

  • Page 56: Appendix B Electrostatic Discharge

    ● Use a portable field service kit with a folding static-dissipating work mat. ● If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider.

  • Page 57: Appendix C Computer Operating Guidelines, Routine Care And Shipping Preparation

    Computer operating guidelines, routine care and shipping preparation Computer operating guidelines and routine care Follow these guidelines to properly set up and care for the computer and monitor: Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and ●...

  • Page 58: Optical Drive Precautions

    ● Safety If any object or liquid falls into the drive, immediately unplug the computer and have it checked by an authorized HP service provider. Shipping preparation Follow these suggestions when preparing to ship the computer: Back up the hard drive files to an external storage device. Be sure that the backup media is not exposed to electrical or magnetic impulses while stored or in transit.

  • Page 59: Index

    26 security memory 14 battery replacement 47 cable lock 40 slim optical drive 30 front bezel 45 HP Business PC Security computer operating guidelines 51 locks Lock 41 cable lock 40 padlock 40 front bezel 45 serial number location 5 DIMMs.

Table of Contents