1. Manuals
  2. Brands
  3. Miele Manuals
  4. Hob
  5. CS 1028
  6. Operating and installation instructions

Miele CS 1028 Operating And Installation Instructions

Gas hob
Hide thumbs Also See for CS 1028:
Table of Contents

Advertisement

Quick Links

Download this manual
Operating and installation instructions
Gas hob
CS 1028 (Town Gas or LP Gas)
en - HK
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 07 206 050

Advertisement

Table of Contents
loading

Related Manuals for Miele CS 1028

Summary of Contents for Miele CS 1028

  • Page 1 Operating and installation instructions Gas hob CS 1028 (Town Gas or LP Gas) en - HK To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
  • Page 2 Per questo se si vuole usare l'apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.
  • Page 3 Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...

  • Page 4: Table Of Contents

    Contents Guide to the appliance ..........6 Front view.
  • Page 5 Contents Installing / removing the appliance ........41 General installation tips .

  • Page 6: Guide To The Appliance

    Guide to the appliance Front view a Pan support b Burner c Control knob...

  • Page 7: Burner

    Guide to the appliance Burner d Burner cap e Burner head f Cover plate g Ignitor h Ignition safety device i Burner base...

  • Page 8: Warning And Safety Instructions

    Warning and Safety instructions This appliance complies with all current local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time.
  • Page 9 The hob is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.
  • Page 10 Warning and Safety instructions Safety with children The hob is not a toy! To prevent the risk of injury, do not let children play with the appliance or its controls. Children under 8 years of age must be kept away from the hob unless they are constantly supervised.
  • Page 11 Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). Before connecting the hob to the mains electricity...
  • Page 12 During installation, maintenance and repair work, the hob must be disconnected from the gas supply and mains electricity supply. While the hob is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated.
  • Page 13 Warning and Safety instructions Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used. If the connection cable is damaged, it must be...
  • Page 14 Warning and Safety instructions Correct use The hob gets hot when in use and remains hot for quite a while after being switched off. Do not touch it whilst it could still be hot. If a cooker hood is installed above the hob, ensure that the burners are always covered with a pan when in use.
  • Page 15 Warning and Safety instructions Use heat-resistant pot holders or gloves when using the hob. Ensure that they do not come into contact with the flames. Do not use large cloths, tea towels or similar as the ends could touch the flames and catch fire.
  • Page 16 Miele cannot be held liable for this type of damage. Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan.
  • Page 17 Warning and Safety instructions Using the hob will cause a build-up of heat and moisture in the room in which it is installed. Ensure that the room has sufficient natural or mechanical means of ventilation, e.g. an extractor. If the hob is used for very long periods of time additional ventilation of the room may be necessary, e.g.
  • Page 18 If the hob has not been used for a long period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested for safety. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

  • Page 19: Caring For The Environment

    Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment.

  • Page 20: Before Using For The First Time

    Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet. Cleaning for the first time ^ Remove any protective foil and stickers.

  • Page 21: Operation

    Operation Switching on, adjusting the Switching on flame and switching off ^ The control for the burner must be pressed in and turned anti-clockwise to the ignition position a to switch ^ When the flame ignites, keep the control pressed in for 8-10 seconds, and then let it go.

  • Page 22: Regulating The Flame

    Operation Regulating the flame The burners can be regulated at any level between the strongest and weakest flame. Control the flame so that it does not spread out beyond the sides of the pan. As the outer part of the flame is much hotter than the centre, the tips of the flames should stay beneath the pan base.

  • Page 23: Pans

    Pans – Use the correct sized pans for your Min. base diameter appliance. A pan which is too small Pots / pans = 22 cm will be unstable on the pan support. If the pan diameter is too large, Max. rim diameter flames can spread out to the sides Pots / pans = 30 cm and damage or burn the worktop,...

  • Page 24: Safety

    Safety Thermo-electric ignition This appliance has a thermo-electric ignition safety device. If the flame goes out, for example if food has boiled over or if there is a sudden draught, the supply of gas to the burner will be cut off.

  • Page 25: Cleaning And Care

    Cleaning and care General notes To avoid damaging the surface or your hob, do not use: Under no circumstances use a – cleaning agents containing soda, steam cleaning appliance to clean alkalines, ammonia, acids or this appliance . The steam could chlorides, attack the electrical components and cause a short circuit.

  • Page 26: Stainless Steel Surfaces

    Cleaning and care Stainless steel surfaces Pan supports, control knobs Clean stainless steel surfaces with a Remove the pan supports. Clean solution of warm water and a little stainless steel surfaces using a solution washing-up liquid applied with a soft of warm water and a little washing-up sponge.

  • Page 27: Burner

    Cleaning and care Burner To reassemble the burner Do not clean any parts of the burner in a dishwasher. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Parts of the burner that cannot be removed should be wiped clean with a damp cloth only.

  • Page 28: Problem Solving Guide

    – the mains fuse has blown. If it has, ensure safety. Repairs and other contact a qualified electrician or the work by unqualified persons could Miele Customer Contact Centre. be dangerous. The manufacturer – food deposits have lodged cannot be held liable for themselves between the ignitor and unauthorised work.

  • Page 29: Optional Accessories

    Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back cover for contact details) Ceramic and stainless steel hob cleaner 250 ml...

  • Page 30: Safety Instructions For Installation

    A gas hob may not be built in over a fridge, fridge freezer, freezer, dishwasher, washing machine or tumble dryer. The hob may only be installed above a Miele oven if the worktop is at least 40 mm thick.
  • Page 31 Safety instructions for installation Safety distance above the appliance Safety Distance below the Hob There should be at least 30 mm height or plenty of space reserved at the bottom of the gas hob for the installation of the flexible gas connection pipe and electrical cable.
  • Page 32 CS 1012 / CS 1012-1 CS 1013 / CS 1013-1 150 mm for CS 1421 CS 1312 CS 1322 200 mm for CS 1034 / CS 1034-1 not allowed 250 mm for CS 1011 CS 1018 CS 1021 CS 1028...
  • Page 33 Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding.

  • Page 34: Appliance And Building-In Dimensions

    Appliance and building-in dimensions CS 1028 a Spring clamps b Front c Building-in depth d Mains connection box with mains connection cable, L = 1440 mm e Gas connection R 1/2 - ISO 7-1 (DIN EN 10226)

  • Page 35: Preparing The Worktop

    Preparing the worktop ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the hob. See "Safety instructions for installation".

  • Page 36: Installation Of Several Appliances

    Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fitting the spacer bars and support brackets". Worktop cut-out Worktop cut-out - two appliances - three appliances When installing three appliances the When installing two appliances, the width of the cut-out required (D) is...
  • Page 37 Installation of several appliances Worktop cut-out calculation example for three appliances Appliance width Appliance Appliance width Worktop less 8 width less 8 cut-out 1032 1424 1124 1516 1136 1320 1136 All dimensions are given in mm...
  • Page 38 Installation of several appliances a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Cover strips The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).

  • Page 39: Fixing The Spring Clamps And Spacer Bars

    Fixing the spring clamps and spacer bars Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied.
  • Page 40 Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops. ^ Apply silcone to the side edges and the lower edges of spring clamps a and spacer bars b. ^ Then fill gap e between the spacer ^ Position and secure the spring bars and the worktop with silicone.

  • Page 41: Installing / Removing The Appliance

    Installing / removing the appliance ^ Starting at the front, position the next Installing the appliance appliance in the worktop cut-out. ^ Feed the connection cable down ^ Connect the appliance(s) to the through the cut-out. mains (see "Electrical connection") ^ Starting at the front, position the and to the gas supply (see "Gas appliance in the worktop cut-out.

  • Page 42: General Installation Tips

    General installation tips Seal between the appliance and the Tiled worktop worktop Grout lines a and the hatched area The sealing strip under the edge of the underneath the surface of the top part of the appliance provides a appliance must be smooth and even. If sufficient seal for the worktop.

  • Page 43: Electrical Connection

    Electrical connection Connection should be made via a All electrical work should be carried suitable isolator or a double pole fused out by a suitably qualified and spur connection unit which complies competent person, in strict with national and local safety accordance with current local and regulations and the on/off switch should national safety regulations.
  • Page 44 If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Service Department. The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection.

  • Page 45: Gas Connection

    Gas connection Connection to the gas supply, or The gas installation must be carried conversion from one type of gas to out so that the connection is not another, should only be undertaken subject to high temperatures when by an registered gas installer the appliance is in use.
  • Page 46 EL-125) comes with the hob. connection connect from ½ “ G If the jets you require are not supplied, connector to governor, and connect up please contact your Miele dealer or the to gas supply point. Service Department. Warning Conversion to another type of gas is described under "Conversion to another...
  • Page 47 Gas connection Connecting the appliance Using a 90° angle The gas connection of the appliance has a 1/2" tapered screw thread. Connection can be made by: – an appropriate rigid connection – a flexible gas connection pipe in accordance with DIN 3383 Section 1 A flexible gas connection pipe must not exceed 2 m in length.

  • Page 48: Conversion To Another Type Of Gas

    Conversion to another type of gas Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an registered gas installer employed by Registered Gas Contractor under the gas safety regulations (Registration of Gas Installers and Gas Contractors).

  • Page 49: Changing The Jets

    Conversion to another type of gas Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by disconnecting the mains fuse. The top of the appliance has to be removed before the jets can be changed.

  • Page 50: To Change The Main Jet

    Conversion to another type of gas To change the main jet ^ Whilst counterholding it in place with ^ Undo the two screws a of the burner an SW 00 spanner, unscrew the main pipe on the underside of the jet c anti-clockwise from its housing appliance.

  • Page 51: To Check The First Intake Of Air

    Conversion to another type of gas To check the first intake of air e Retaining nut f Air intake sleeve Gap X must measure: For Town Gas: 4 mm For Natural Gas: 6 mm For Liquid Petroleum Gas : 5 mm If it does not: –...

  • Page 52: To Change The Small Jets

    Conversion to another type of gas To change the small jets ^ Using a small screwdriver, unscrew small jet g in the gas fitting. ^ Pull out the jet with a pair of pliers. ^ Fit the correct jets securely (see jet table).

  • Page 53: After Changing The Jets

    Conversion to another type of gas After changing the jets The flame must not go out on the lowest setting, or when the control is turned ^ Reassemble the burner parts in the quickly from a high to a low setting. reverse order, On the highest setting, the flame must ^ Check all gas fittings for leaks by...

  • Page 54: After Sales Service, Data Plate

    Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.
  • Page 56 Alteration rights reserved/ 3313 M.-Nr. 07 206 050 / 05...

Table of Contents