Lincoln 1998 Mark VIII Owner's Manual
  1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. 1998 Lincoln Mark VIII
  6. Owner's manual

Lincoln 1998 Mark VIII Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Starting
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
1997 Ford Motor Company
Contents
Elemental Chlorine Free
2
3
32
66
88
93
107
123
161
167
168
1

Advertisement

Table of Contents
loading

Related Manuals for Lincoln 1998 Lincoln Mark VIII

Summary of Contents for Lincoln 1998 Lincoln Mark VIII

  • Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1997 Ford Motor Company...

  • Page 2: Introduction

    If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.

  • Page 3: Instrumentation

    Instrumentation Instrument Instrument panel cluster dimmer switch (pg. 6) (pg. 33) Headlamp control (pg. 32) ACCEL COAST Turn signal and wiper/washer control (pg. 41) Speed control Ignition switch Driver side (pg. 43) (pg. 40) air bag (pg. 77)

  • Page 4: Message Center

    Instrumentation Message Center (pg. 14) VOL-PUSH ON FM 1 FADE AUTO BASS TREB SEEK DOLBY 8 NR SCAN TAPE CD TUNE DISCS SIDE 1-2 COMP SHUFFLE AUTOMATIC OUTSIDE TEMP FLR•DEF MAX A/C VENT PNL•FLR FLOOR HEATED SEAT HEATED SEAT R.DEF. BOTH BOTH BACK...
  • Page 5 Instrumentation WARNING LIGHTS AND CHIMES FUEL FILL DOOR km/h RPMx1000 PREMIUM FUEL 000000.0 BRAKE CRUISE RECOMMENDED Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately.
  • Page 6 Instrumentation Engine oil pressure Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter.
  • Page 7 Instrumentation Speed control (if equipped) This light comes on when either the CRUISE SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position.
  • Page 8 Instrumentation Message center warning lights The following warning lights are displayed directly above the message center controls. CHECK ANTI ENGINE THEFT Safety belt Illuminates when the ignition is turned on to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter.
  • Page 9 Instrumentation engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing. What you should do if the check engine light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction.
  • Page 10 Instrumentation O/D off This light momentarily illuminates when the ignition is turned to ON. It also illuminates when the transmission control switch been pushed. When the light is on, the transmission does not shift into overdrive. If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving, have your vehicle serviced.
  • Page 11 Instrumentation Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. GAUGES FUEL FILL DOOR...
  • Page 12 Instrumentation Never remove the coolant recovery cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Tachometer Indicates the engine speed in revolutions per minute.
  • Page 13 Instrumentation Odometer Indicates the total kilometers (miles) of the vehicle. km/h 000000.0 Fuel gauge Displays approximately how much FUEL FILL DOOR fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion.
  • Page 14 Instrumentation Selectable features You can select different features for the message center to display by using the message center controls located below the message center display. You will hear a tone when you press one of these controls. However, the message center will display the appropriate warning message if it detects a warning from any of the monitored systems.
  • Page 15 Instrumentation • OIL CHANGE RESET. This feature allows you to reset the oil monitoring system to 100 percent after each oil change. To reset, the RESET control must be pressed and held for 5 seconds while the display counts down. After a successful reset, the message center will display “OIL LIFE RESET TO 100%.”...
  • Page 16 Instrumentation 3. Press the RESET control to obtain the desired personalized oil change percentage. Your choices are 100%, 90%, 80%, 70%, 60%, 50%, 40% and 30%. 4. Press the VEHICLE SETTING control to complete the procedure. A press of any control other than RESET or VEHICLE SETTING will abort the procedure and will not establish a new personalized oil...
  • Page 17 Instrumentation • EXPRESS WINDOWS. Allows one tap down operation of the driver’s window using the window switch. • AUTO LOCK. Automatically locks all doors when all doors are closed and the vehicle speed is at least 5 km/h (3 mph). •...
  • Page 18 Instrumentation Press RANGE a second time to display the approximate amount of fuel left in the tank in whole numbers (liters or gallons). If the fuel tank is full or nearly full, the message center will display FULL FUEL TANK. If the fuel tank is nearly empty, the message center will display EMPTY FUEL TANK.
  • Page 19 Instrumentation Trip ODO Press this control to display the first of two trip odometers. Press it again to display the second trip odometer. To reset the displayed trip odometer, press the RESET control. Reset Press this control to reset: • warnings •...
  • Page 20 Instrumentation Day and date display To set the day: 1. Press the RESET control. 2. Press DATE/TIME repeatedly to select the correct day of the week. To set the month: 1. Press RESET to proceed to the month adjustment display. 2.
  • Page 21 Instrumentation • To stop the elapsed time count while it is running without resetting the counter, briefly (less than two seconds) press the RESET control. • To start the elapsed time count when it is stopped without resetting the counter, briefly (less than two seconds) press the RESET control.
  • Page 22 Instrumentation 2. Determine which compass zone you are in by referring to the zone map. 3. Press the ECONOMY control until the current zone number is shown in the display. 4. Press the RESET control until the number shown in the display is the correct number for the zone you are 5.
  • Page 23 Instrumentation 3. Press the RESET control to enter the calibration mode. The display will show CIRCLE SLOWLY TO CAL. 4. Slowly drive the vehicle at less than 5 km/h (3 mph) in a circle, taking at least 20 seconds to complete one circle, until the display shows a direction (north, south, etc.).
  • Page 24 Instrumentation At normal conclusion of the system check sequence, the last displayed feature will be displayed. Press the RESET control anytime during the system check to stop the cycle immediately. The last displayed feature before RESET was pressed will be displayed. Press any of the other message center controls to stop the system check cycle and display the...
  • Page 25 Instrumentation In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages.
  • Page 26 Instrumentation Driver’s door ajar Warning cannot be reset Right door ajar Check engine temp Warning returns after 10 minutes Low oil level Check charging system Low fuel level Low engine coolant Engine temp data err Check transmission Transmission overheat Check brake lamps Warning returns after the ignition key is turned from OFF to ON or Check headlamps...
  • Page 27 Instrumentation LOW OIL LEVEL. Displayed when the engine oil level is low. If this warning message is displayed, check the level of the engine oil. If you are parked on a steep incline, the LOW OIL LEVEL message may come on when you start your vehicle, even though the oil is at the correct level.
  • Page 28 Instrumentation TRANSMISSION OVERHEAT. Indicates the transmission is overheating. This warning may appear when towing heavy loads or when driving in a low gear at a high speed for an extended period of time. Stop the vehicle as soon as safely possible, turn off the engine and let it cool.
  • Page 29 Instrumentation CHECK AIR RIDE SYSTEM. Displayed when the air suspension system is not operating properly. If this message is displayed while driving, pull off the road as soon as safely possible. The message may also be displayed if the vehicle is loaded beyond the recommended maximum payload.
  • Page 30 Instrumentation 2. Press the RESET switch and hold it down for five seconds while the display counts down to trigger an oil change reset. 3. After a successful reset, the message center will display OIL LIFE RESET TO 100% (if you have established a personalized oil reset percentage, the display will instead show that percentage).

  • Page 31: Controls And Features

    Controls and features HEADLAMP CONTROL Rotate the headlamp control AUTO LAMP DELAY clockwise to the first position to turn on the parking lamps only. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the highbeam headlamps on with a reduced output.

  • Page 32: Controls And Features

    Controls and features Flash to pass Pull toward you to activate and release to deactivate. TIME MIST PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Rotate up to brighten. • Rotate down to dim. • Rotate fully up to turn on interior lights.

  • Page 33: Climate Control System

    Controls and features preselected time lapse is adjustable up to approximately three minutes by continuing to rotate the control counterclockwise. • To turn autolamps off, rotate the control clockwise to OFF. • A small LED illuminates next to the autolamp control to indicate that the headlamps have been turned on by the autolamps.
  • Page 34 Controls and features Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if fresh outside air or recirculated air is required.
  • Page 35 Controls and features For continuous maximum heating, push the red button until 32°C (90°F) is shown in the display window. The EATC will continue maximum heating (disregarding the displayed temperature) until a cooler temperature is selected by pressing the blue button. Temperature conversion Press MAX A/C and DEF at the...
  • Page 36 Controls and features Manual override controls The override controls are located at the bottom of the EATC and allow AUTO you to determine where airflow is OUTSIDE TEMP AUTOMATIC directed. To return to full automatic MAX A/C VENT PNL • FLR FLOOR FLR •...
  • Page 37 Controls and features • FLOOR-Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. • FLR •DEF-Distributes outside air through the windshield defroster ducts and the floor ducts.
  • Page 38 Controls and features moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations. Operating tips • In humid weather, select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position.
  • Page 39 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located R. DEF on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
  • Page 40 Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for TIME intermittent wipers. When in this MIST position rotate the control upward for fast intervals and downward for slow intervals.
  • Page 41 Controls and features POWER TILT/TELESCOPE STEERING COLUMN Never adjust the steering wheel when the vehicle is moving. The steering column can be adjusted manually by moving the four-way rocker adjustment control located on the multi-function control below the turn signal/wiper control stalk.
  • Page 42 Controls and features If attempting to manually adjust the steering column and it does not respond see your local dealer for service. SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
  • Page 43 Controls and features Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
  • Page 44 Controls and features To set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACC/SET ACCEL ACCEL. Each press will increase the set speed by 1.6 km/h COAST (1 mph) or •...
  • Page 45 Controls and features • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. ACCEL COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 46 Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). ACCEL COAST Indicator light This light comes on when either the CRUISE SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
  • Page 47 Controls and features Do not use the HomeLink Universal Transmitter with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S.
  • Page 48 Controls and features Note to Canadian residents During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transmitter. If you are programming from one of these hand-held transmitters: •...
  • Page 49 Controls and features Training a rolling code system Rolling code systems (garage door openers which are “code protected”) may be determined by the following: • The hand-held transmitter appears to program the HomeLink Universal Transmitter but does not activate the garage door. •...
  • Page 50 Controls and features ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover. MOON ROOF (IF EQUIPPED) To open the moon roof: • Press the front portion of the control to raise the moon roof to the vent position (when the glass ROOF panel is closed).
  • Page 51 Controls and features INTERIOR LAMPS Map lamps To turn on the map lamps, slide the control to the ON position. ROOF To turn off the map lamps, slide the control to the OFF position. POWER WINDOWS Press and hold the rocker switches to open and close windows. •...
  • Page 52 Controls and features • Press the bottom portion of the rocker switch to open. AUTO Express down • Press AUTO and release quickly. The window will open fully. Depress again to stop window operation. This function is programmable in the vehicle settings.
  • Page 53 Controls and features POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. Smart locks With the key in the ignition, in any switch position, and either the driver’s or passenger’s door open, the doors cannot be locked using the front door lock switches.
  • Page 54 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. DRIVER PROFILE SYSTEM The Personality Memory feature customizes your vehicle for up to two drivers.
  • Page 55 Controls and features Recalling Personality Memory All of these settings are automatically recalled when the driver unlocks the door using the remote entry transmitter, keyless entry keypad or selects either Memory 1 or Memory 2. The vehicle must be in P (Park ) or N (Neutral) to recall Personality Memory settings.
  • Page 56 Controls and features Auto save Any change made by the driver to one or more of the above Personality Memory settings will be updated and saved automatically. The display, DRIVER 1 (or DRIVER 2) SETTING SAVED, will appear on the Message Center for five seconds as a confirmation of the update to Personality Memory.
  • Page 57 Controls and features Cellular phone Refer to the “Cellular phone guide” for instructions on operation. POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
  • Page 58 Controls and features Locking the doors Press this control to lock all doors. The horn will chirp to confirm that the control was pressed. The horn chirp feature can be turned on/off by using the feature menu in the message center. This process will arm your anti-theft system (if equipped).
  • Page 59 Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
  • Page 60 Controls and features When pressing the controls on the keyless entry keypad, press the middle of the buttons to ensure a good activation. Programming your own entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1.
  • Page 61 Controls and features Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of prior digit). The interior lamps will illuminate. To unlock all doors, enter the factory-set code or personal code (driver door unlocks) and press 3/4...
  • Page 62 Controls and features Autolock The autolock feature will lock all of the doors when: • all vehicle doors are fully closed • the ignition key is turned to the ON position • the vehicle is in a forward gear and •...
  • Page 63 Controls and features • Pressing 7/8 and 9/0 on the keyless entry pad at the same time to lock the doors (doors 7 8 9 0 opened or closed). • Opening a door and pressing the power door lock control to lock the doors.
  • Page 64 Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to a Ford/Lincoln-Mercury dealership for re-programming. Programming additional keys If you need additional keys electronically coded for your vehicle, spares can be purchased (a maximum of 16 keys can be programmed).

  • Page 65: Seating And Safety Restraints

    Seating and safety restraints SEATING The head restraints can be moved in four directions: • up and down • forward or backward Adjusting the power seats The power seat controls are located on the outboard side of the seat. Never adjust the driver’s seat or seatback when the vehicle is moving.

  • Page 66: Seating And Safety Restraints

    Seating and safety restraints Push the horizontal control to move the seat forward or backward. Push the vertical control to move the seatback. Heated seats (if equipped) To operate the heated seats: • Push the control to select BACK HEATED SEAT to heat the seatback only.
  • Page 67 Seating and safety restraints • Rotate the control to select the desired heat (from OFF to HI). HEATED SEAT Allow five minutes for the heat level to stabilize. BOTH BACK PUSH If the heated seat switch is not turned OFF, the seat will heat up to the selected temperature level each time the vehicle is started.
  • Page 68 Seating and safety restraints Emergency seatback release lever Lift the lever to release the seatback. It is not necessary to use the release lever for rear seat entry or exit. The seatback remains unlocked with normal usage and locks only during emergency stopping, upon impact, or on steep downhill grades.
  • Page 69 Seating and safety restraints With the ignition OFF: • the driver seat Auto-Glide will function when the gearshift is in N (Neutral) or P (Park) and at least one of the vehicle doors is opened. • the passenger seat Auto-Glide will only function when at least one of the vehicle doors is opened.
  • Page 70 Seating and safety restraints SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
  • Page 71 Seating and safety restraints Combination lap and shoulder belts 1. To fasten, insert the tongue into the slot in the buckle. 2. To unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
  • Page 72 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode •...
  • Page 73 Seating and safety restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
  • Page 74 Seating and safety restraints Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
  • Page 75 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However,...
  • Page 76 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) VOL-PUSH ON FM 1 FADE AUTO BASS TREB ACCEL COAST SEEK DOLBY 8 NR SCAN TAPE CD TUNE DISCS SIDE 1-2 COMP SHUFFLE OUTSIDE TEMP AUTOMATIC MAX A/C VENT PNL•FLR FLOOR FLR•DEF HEATED SEAT...
  • Page 77 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags...
  • Page 78 Seating and safety restraints How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
  • Page 79 Seating and safety restraints If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 80 Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN Important child restraint precautions You are required by law to use safety restraints for children in the U.S.
  • Page 81 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 82 Seating and safety restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
  • Page 83 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
  • Page 84 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
  • Page 85 Seating and safety restraints 10. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine.
  • Page 86 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit.
  • Page 87 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.

  • Page 88: Starting

    Starting Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts. For more information on safety belts and their proper usage, refer to the Seating and safety restraints chapter. 2. Make sure the headlamps and vehicle accessories are off. 3.
  • Page 89 Starting FUEL FILL DOOR km/h RPMx1000 PREMIUM FUEL 888888.8 BRAKE CRUISE RECOMMENDED CHECK ANTI ENGINE THEFT Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light ( ) will not illuminate.
  • Page 90 Starting STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the engine does not start within five seconds, wait ten seconds and try again.
  • Page 91 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.
  • Page 92 Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.

  • Page 93: Driving

    Driving ABS warning lamp warning lamp in the instrument cluster illuminates for about five seconds when starting the vehicle. If an ABS fault is detected, the light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective BRAKE unless the BRAKE warning lamp is...
  • Page 94 Driving The BRAKE warning lamp in the BRAKE instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure the gearshift is latched in P (Park).
  • Page 95 Driving TRACTION CONTROL Your vehicle is equipped with the Traction Control system. This system helps maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates at all speeds by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS).
  • Page 96 Driving AIR SUSPENSION SYSTEM The air suspension system is designed to improve ride, handling and general vehicle performance during: • certain road conditions • steering maneuvers • braking • accelerations This system maintains the vehicle height at a constant level by automatically adding air or releasing air from the air springs to offset changes in vehicle loads.
  • Page 97 Driving 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N (Neutral). 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift, it is possible that a fuse has blown and the vehicle’s brake lamps may not be operating properly.
  • Page 98 Driving P (Park) Always come to a complete stop R N D 2 1 before shifting into or out of P (Park). Make sure the gearshift is securely latched in P (Park). R (Reverse) With the gearshift in R (Reverse), R N D 2 1 the vehicle will move backward.
  • Page 99 Driving N (Neutral) With the gearshift in N (Neutral), R N D 2 1 the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. D (Overdrive) The normal driving position for the R N D 2 1 best fuel economy.
  • Page 100 Driving D (Overdrive) can be deactivated by pressing the transmission control switch on the side of the gearshift lever. The Message Center O/D OFF indicator will illuminate. D (Drive) – Activate by pressing the transmission control switch on the side of the gearshift lever. The transmission operates in gears one through three.
  • Page 101 Driving 2 (Second) Use 2 (Second) to start-up on R N D 2 1 slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum R N D 2 1 engine braking on steep downgrades.
  • Page 102 Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment.
  • Page 103 Your vehicle is classified as a light duty towing vehicle. It does not come from the factory fully equipped to tow. No towing packages are available through Ford or Mercury/Lincoln dealers. Do not tow a trailer until your vehicle has been driven at least 3 200 km (2 000 miles).
  • Page 104 Driving Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle.
  • Page 105 Driving Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.

  • Page 106: Roadside Emergencies

    Roadside emergencies HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column.

  • Page 107: Roadside Emergencies

    Roadside emergencies The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
  • Page 108 Roadside emergencies Standard fuse amperage rating and color Fuse rating Color 5 amp 7.5 amp Brown 10 amp 15 amp Light blue 20 amp Yellow 20 amp fuse link Light blue 25 amp Natural 30 amp Light green 30 amp fuse link Pink 40 amp fuse link Green...
  • Page 109 Roadside emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover. 10 A 10 A 10 A 10 A 10 A 15 A 30 A 10 A 10 A 15 A 30 A 20 A 10 A 10 A 10 A...
  • Page 110 Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating Day/Night Sensor, Cluster (Oil Pressure, Brake Warning, Speed Control), I/P Warning Indicator Display, Steering Column/Ignition/Lighting Module (Logic Input) Starter Motor Relay Steering Column/Ignition/Lighting Module (Left Turn Lamps) — Not Used Blower Motor Relay, Electronic Automatic Temperature Control Module Windshield Wipers Coil Drivers, Radio Noise Capacitors, PCM...
  • Page 111 Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating Steering Column/Ignition/Lighting Module (Right Low-Beam Headlamp) Steering Column/Ignition/Lighting Module (Courtesy Lighting, Demand Lighting) — Not Used Instrument Cluster, I/P Warning Indicator Display, Air Suspension/EVO Steering Module, Rear Window Defrost Module, Steering Wheel Position Sensor, Transmission Control Switch —...

  • Page 112: Servicing

    Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
  • Page 113 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Description Location Rating 10A* Powertrain Control Module (Keep-Alive Memory) 15A* High Beam Relay, Daytime Running Lamps Module 10A* Powertrain Control Module (EAM Pump Motor-Monitor) 15A* Air Suspension, Electronically Variable Orifice Power Steering 30A* Trunk Lid Relay, Fuel Filler Door Release...
  • Page 114 Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating 30A** Anti-Lock Brake Control Module 20A** Anti-Lock Brake Control Module, EVAC/Fill Connector 60A** I/P Fuses (1, 7, 13, 19, 25, 31) 40A** Variable Load Control Module 40A** Rear Window Defrost Control, I/P Fuse 30 60A** I/P Fuses (2, 14, 20, 26, 32, 38), Engine Compartment Fuse 5...
  • Page 115 Roadside emergencies 3. Remove the spare tire, jack and lug wrench. 4. Remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel.
  • Page 116 Roadside emergencies On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspension system in the Driving chapter for more information. 6. Put the jack in the jack notch next to the door closest to the tire you are changing.
  • Page 117 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
  • Page 118 Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter.
  • Page 119 Roadside emergencies Connecting the jumper cables 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine. Switch off any unnecessary electrical equipment. 3. Connect the positive ( +) terminal of the discharged battery (1) to the positive ( +) terminal of the booster battery (2).
  • Page 120 Roadside emergencies Removing the jumper cables 1. Remove the jumper cables in reverse order. Take the cable off the metallic surface (1) first, followed by the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive ( +) terminal of the booster battery (3) and then the discharged battery (4).
  • Page 121 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle.
  • Page 122 Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.

  • Page 123: Maintenance And Care

    Maintenance and care Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1.
  • Page 124 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L DOHC ENGINE 1. Air filter assembly 2. Transmission fluid dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Battery 6. Windshield washer fluid reservoir 7. Power steering fluid reservoir 8.
  • Page 125 Maintenance and care ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
  • Page 126 Engine oil recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments.
  • Page 127 Severe duty operation would include extensive idling, trailer towing, driving in severe dust and police, taxi or delivery service. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
  • Page 128 Maintenance and care Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever...
  • Page 129 Maintenance and care ENGINE COOLANT Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may eventually empty.
  • Page 130 Ford specification ESE-M97B44–A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for four years or 80,000 km (50,000 miles). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
  • Page 131 Maintenance and care Severe winter climate If you drive in extremely cold climates (less than –36°C [–34°F]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months.
  • Page 132 Maintenance and care TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the “Service Guide.” Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter.
  • Page 133 Maintenance and care If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking.
  • Page 134 Maintenance and care BATTERY Your vehicle may be equipped with a Superstart maintenance-free battery. If the original equipment battery needs replacing, it may be replaced with a low-maintenance battery. The low-maintenance battery normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check your battery electrolyte level, at least...
  • Page 135 Maintenance and care 3. The relearning process will automatically complete as you drive the vehicle. • If you do not allow the engine to relearn its idle, the idle quality of your vehicle may be adversely affected until the idle is eventually relearned.
  • Page 136 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
  • Page 137 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
  • Page 138 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
  • Page 139 Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over.
  • Page 140 Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
  • Page 141 Maintenance and care • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors or skin contact could cause an adverse reaction. Consult a physician immediately. Choosing the right fuel Use only UNLEADED FUEL.
  • Page 142 It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
  • Page 143 If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emission control such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
  • Page 144 Maintenance and care sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine.
  • Page 145 Maintenance and care • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs The high beam headlamps on your vehicle use halogen bulbs.
  • Page 146 Maintenance and care 4. Remove the retaining screw from the corner of the headlamp assembly. 5. Remove the bolts from the top of the headlamp assembly. 6. Gently pull the headlamp assembly forward. Noting the location of each connector, disconnect the wire connectors from the headlamp assembly.
  • Page 147 Maintenance and care 9. Remove the headlamp bulb retaining nuts. 10. Remove the headlamp bulb assembly. 11. Slide the headlamp level and bracket off the bulb assembly and remove. 12. Twist headlamp housing counterclockwise to remove headlamp bulb from socket.
  • Page 148 Maintenance and care To install the new low beam headlamp bulb: 1. Insert the new bulb into the socket and twist clockwise to lock into place. 2. Pull the headlamp level and bracket over the bulb assembly and snap into place. 3.
  • Page 149 Maintenance and care 5. Position the low beam headlamp housing cover over the bulb assembly and rotate clockwise to lock into place. 6. Match the remaining wire connectors with their proper mates and reinstall. 7. Reinstall the top bolts. Tighten 1/2 turn past finger tight.
  • Page 150 Maintenance and care 9. Replace the sight shield. 10. Reconnect the battery ground cable and close the hood. Replacing the high beam headlamp bulb To remove the high beam headlamp bulb: 1. Make sure the headlamp switch is in the OFF position. 2.
  • Page 151 Maintenance and care 4. Rotate the plastic bulb base counterclockwise and pull the bulb assembly out of the housing. 5. Pull the bulb socket retaining clip outward while carefully pulling up on the plastic base of the bulb. To install the new high beam headlamp bulb: 1.
  • Page 152 Maintenance and care 2. Push the bulb down into the socket until the retaining clip snaps over it. 3. Carefully insert the bulb assembly into the headlamp housing while aligning the locking tabs. 4. Rotate the bulb assembly clockwise to lock it into place. 5.
  • Page 153 Maintenance and care Using the right bulbs Function Trade Number Headlamp low beam 9500 Headlamp high beam 9005 Park and turn lamp (front) 3157 NAK Side marker lamp (front) Cornering lamp (front) 3156 Tail lamp, brakelamp, turn lamp 3057K Side marker (rear) Backup lamp 3156 License plate lamp...
  • Page 154 Maintenance and care The following procedure assumes that the vehicle’s front structure is properly aligned. If the vehicle has been in an accident requiring the front end of the vehicle to be repaired, the horizontal indicator should be recalibrated by the service facility. Horizontal aim adjustment 1.
  • Page 155 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar...
  • Page 156 Maintenance and care Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar.
  • Page 157 Maintenance and care Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary.
  • Page 158 Maintenance and care Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage. Cleaning leather seats (if equipped) For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap. If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product “Tanners Preserve Leather Cleaner”...
  • Page 159 Maintenance and care Do not use household cleaners, glass cleaner, alcohol solutions or cleaner intended for vinyl, rubber or plastics. These products can damage the leather. In some instances, color or dye transfer can occur when wet clothing (wool, denim, leathers or other non-colorfast garments) comes in contact with leather upholstery.

  • Page 160: Capacities And Specifications

    Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.6L engine Air filter FA-1602 Fuel filter FG-881 Battery (standard) BXT-65-650 Battery (optional) BXT-65-850 Oil filter FL-820S PCV valve EV-111 Spark plugs* AWSF-32EE** * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.

  • Page 161: Capacities And Specifications

    Capacity Engine oil Motorcraft 5W30 Super (includes filter Premium Motor Oil 5.7L (6.0 quarts) change) Brake fluid Ford High Performance DOT Fill to line in 3 Brake Fluid reservoir Power steering Motorcraft MERCON ATF Fill to line in fluid reservoir...
  • Page 162 Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford part name Ford part Ford number specification Brake master High Performance C6AZ- ESA-M6C25-A, cylinder DOT 3 Motor 19542-AB DOT 3 Vehicle Brake Fluid Door Silicone Lubricant C0AZ-19553- ESR-M13P4-A weatherstrips AA and D7AZ- 19553-AA...
  • Page 163 Capacities and specifications ENGINE DATA Engine 4.6L DOHC engine Cubic inches Horsepower (except LSC) 280 @ 5750 rpm Horsepower (LSC) 290 @ 5750 rpm Torque (except LSC) 285 lb. ft. @ 4500 rpm Torque (LSC) 290 lb. ft. @ 4500 rpm Recommended fuel grade 91 octane Firing order...
  • Page 164 Capacities and specifications...

  • Page 165: Vehicle Identification Number

    Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. Administration Regulations require DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG that a Safety Compliance FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL...

  • Page 166: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
  • Page 167 Index Aiming headlamps ....154 Climate control system Air bag supplemental restraint automatic temperature system ..........77 control ....34,35,36,37,38,39 and child safety seats ....78 Compass, electronic ....22,23 description ........77 Controls ........57,58 disposal ........81 Defrost indicator light ......80 rear window ......40 passenger air bag .....79 Emission control system ..144 Air suspension Engine ........164...

  • Page 168: Index

    Index Heating ........34 Moon roof ........51 High beams Panic alarm feature, remote indicator light ......8 entry system ........60 Hood Parking brake ......94 release lever ......124 Parts (see Motorcraft parts) ..161 Ignition Power door locks ......54 positions of the ignition ...40 Power steering Instrument panel fluid, checking and adding ..132...
  • Page 169 Index Speedometer .......13 Trunk Starting your vehicle .....88,91 using the remote entry Sunvisor ........51 system to open ......59 Tachometer Turn signal mechanical cluster ....13 lever ...........41 Tilt steering wheel ......42 Universal transmitter ....47 Tires ........137,139 erasing channels .......50 changing ........115 operating ........49 checking the pressure ....139 programming ......48...

  • Page 170: Filling Station Information

    Fuel tank capacity 68.1L (18.0 gallons) Engine oil capacity (with filter 5.7L (6.0 quarts). Use Motorcraft change) 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G Automatic transmission fluid 12.0L (12.8 quarts). Use capacity Motorcraft MERCON V ATF (part# XT-5-QM), Ford...

Table of Contents