Oven Sensor; Convection Fan Assembly; Bake Burner And Ignitor; Broiler Burner And Ignitor - Maytag AGR5715QD Service Manual

Disassembly Procedures
!

Oven Sensor

1. Disconnect power before servicing.
2. Open oven door and remove screws securing sensor
to oven cavity.
NOTE: Gently pull wiring through cavity wall.
3. Disconnect oven sensor at the connector terminal
and remove.
4. Reverse procedure to reinstall sensor.
NOTE: Verify connection is pushed through the
insulation.

Convection Fan Assembly

1. Turn off power to unit.
2. Open oven door or remove oven door, see "Door
Removal".
3. Remove screws securing convection fan cover to
convection fan assembly.
4. Remove screws securing convection fan assembly to
rear of oven cavity.
5. Slide convection fan assembly down and tilt forward
on the top portion to allow assembly to pass through
rear oven cavity.
6. Disconnect and label wires from convection fan
motor.
7. Reverse procedure to reinstall convection fan
assembly.

Bake Burner and Ignitor

1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove oven door and racks.
4. Remove screws securing bottom bake cover.
5. Raise the back of the bake burner cover and slide
cover back to release the front edge of cover and lift
out of oven cavity.
6. Remove screws securing bake burner assembly to
the oven chassis.
7. Maneuver bake burner from the burner orifice and out
of the slotted location.
8. Pull forward on assembly to allow the ignitor terminal
plug to pass through the back of the oven cavity.
9. Disconnect terminal plug and remove assembly from
the oven cavity.
10.Remove screws securing ignitor to bake burner.
11. Replace and reassemble in reverse order.
30
WARNING
16022498 Rev. 0
To avoid risk of electrical shock, personal injury, or death:
disconnect electrical and gas supply before servicing.
Broil Burner and Ignitor
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove oven door, and racks.
4. Remove screws securing ignitor wire plate cover to
back of the oven cavity.
5. Maneuver ignitor wire terminal plug through the rear
of the oven cavity.
6. Disconnect ignitor wire terminal plug.
7. Remove screws securing broiler to oven cavity.
8. Carefully maneuver burner off of the broiler orifice
spud and remove from cavity.
9. Remove screws securing ignitor to broiler.
10.Remove wing nut securing flame spreader to broiler.
11. Replace and reassemble in reverse order.

Valve / Regulator Assembly

NOTE: Requires removal of range from installation
position.
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove nut securing broiler tubing to gas valve.
4. Remove nut securing bake tuning to gas valve.
5. Remove screws securing assembly to unit chassis.
6. Disconnect wires and gas lines to gas valve.
7. Replace and reassemble in reverse order.

Automatic Oven Door Latch Assembly

NOTE: Requires removal of range from installation
position.
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove screws securing latch assembly to the front
of the oven cavity outer shell.
3. Disconnect and label wire terminals from latch
assembly.
4. Remove screws securing upper rear access panel to
the back of the unit.
5. Remove screws securing latch assembly to the back
of the unit chassis.
6. Reverse procedure to reinstall door latch assembly.

Spark Module

NOTE: Requires removal of range from installation
position.
1. Remove screws securing lower rear access panel.
2. Disconnect and label wire connections from the spark
module.
3. Remove screws securing spark module to unit
chassis.
4. Replace and reverse procedure to reassemble.
©2003 Maytag Appliances Company