Zte AC30 Quick Start Manual

Introduction
ZTE AC30 is a 3G/2G mobile hotspot device, working in CDMA/1X/EVDO
network. The client devices could connect to it via USB or Wi-Fi interface.
The device supports data and SMS services, enabling you to communicate
anytime and anywhere.
This quick guide provides instructions on how to install and get started with
the product. For information about connection of services, please consult
your service provider. And all images in this document are only for reference.
Specification
ZTE AC30

Quick Start Guide

HSPA: DL 7.2 Mbps
UL 5.76 Mbps
Data Service
EVDO: DL3.1 Mb/s
UL1.8 Mb/s
Interface USB and Wi-Fi
Wi-Fi Standard 802.11 b/g
Wi-Fi Security WEP/WPA/WPA2
USB Version USB 2.0 HIGH SPEED
USB Interface Type Mini USB-B
Weight 80 g
Dimensions (W×H×D): 99.7 mm*53.7 mm*13.9 mm
Power Adapter 5 V/700 mA
Battery 1500 mAh
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China *Standby time 100 hours
Postcode: 518057 Tel: +86-755-26779999
*Working time 4 hours
URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn
2
Interface and Buttons
Windows 7, Windows Vista, Windows XP (SP2 or
Operate system
later), MAC 10.4 or later
1. Power Press and hold the Power key for five seconds to switch the
IE (7.0 or later), Firefox (3.0 or later), Opera (10.0 product on or off.
Web Browser
or later), Safari (4.0 or later), Chrome (5.0 or later)
2. Indicator It indicates your product status
Operating temperature 0 °C ~ +35 °C
3. Charger/ • Charge your device
Storage temperature -20 °C ~ +50 °C USB port
• Connect the client to your device via USB cable
Charging temperature 0 °C ~ +45 °C
LED Indicator
Humidity 5% ~ 95%
Notes: Indicator Status
microSD is a trademark of SD Card Association.
RED glittering Please charge
The device's standby and working time are only for your reference, and
RED bright Voltage of battery is low
based on ideal working environment.
Battery
Getting to Know Your Device Green glittering Charging
indication
Green bright Voltage of battery is high
The following figure shows the appearance of the device, it is only for your
reference. The actual device may be different. LED off No battery.
ERROR or NO signal or NO network
Red bright
service
Signal
GREEN glittering Signal is ok
strength
indication
Green bright Signal is good
LED off Low power mode
LED off WIFI is inactive or low power mode
Wi-Fi
BLUE bright WPS is active
indication
Blue bright Wi-Fi is active
3 4
3. Line the battery cover up correctly and press gently to close the case.
RED glittering 2G Modem data transferring
RED bright Register on 2G network
Network GREEN glittering 3G Modem data transferring
indication
GREEN bright Register on 3G network
ERROR or NO signal or NO network
LED off Switching On/Off Your Device
service
Notes: Hold the Power button to switch on/off the device.
Notes:
* The battery LED will be GREEN bright once the battery is fully charged
The device is powered on when the signal strength indication lights up.
when power on.
Description
* The battery LED will be turn off once the battery is fully charged when
Charging Your Device
power off.
You can charge your device by using USB cable or adapter.
Hardware Installation
1. Insert the charger lead carefully with the plug arrow facing the bottom of
the device.
Inserting Battery 2. The plug only fits one way. Do not use excessive force to insert the plug.
3. Make sure the plug is the right way round and lined up correctly and
1. Use the thumb catch at the bottom of the device to open the battery
insert it gently.
cover.
2. Insert the battery as shown with the contacts located against the metal
Connect your device to PC (Only available for Modem
springs, and press the battery down into the case.
Mode)
1. Connect the product and the computer with the provided USB data
cable.
2. Switch on the device, the system will recognize you device and begin to
install the software.
5
Notes:
Do not put anything on the top of router. Do not lay routers to overlap each
other
Working Mode
Your device supports two working modes. For the client, we only use PC or
laptop as the example in this document.
USB Mode: Connect to the device with the USB cable.
Wi-Fi Mode: Connect to the device via Wi-Fi.
Mixed Mode: Connect to the device with the above two connection methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure that
the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices can
surf on the Internet at the same time.
6 7
Establishing a Connection Between Your Device
and the Client
Via USB Cable
Connect your device and the client with the USB cable.

 Power on your device.
Follow the system prompts to complete the software installation:

A. Click Next to start the installation.
8