Sony MZ-RH910 Service Manual page 19

Example of Calculation:
Item No. Parameter
0211 Pr_nominal 2.48 mW
−0.3 %/°C
0212 Kr
0213 Pw_nominal 7.35 mW
−0.4 %/°C
0214 Kw
0215 Prmin 1.9 mW
0216 Pwmin 5.8 mW
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the key once, press the [VOL+] key once, and press
>
the key once again to display as follows.
>
Display of the remote commander
210 DiscPr
4. Press the key once to select the item number 0211.
>
5. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of LCD becomes calculated value.
6. Press the key on the set or
X
commander to write the adjusted value.
7. Press the key to next item.
>
8. Repeat adjustment from step 4 until item number 0216.
3-5-2. Destination setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the key five time to select the item number 0113
>
and display as follows.
Display of the remote commander
113 DistFL **
adjustment value (hexadecimal)
4. Press the [VOL+]/[VOL--] key and set the according value to
each destination referring to the following table.
5. Press the key on the set or
X
commander to write the adjusted value.
6. Press the key to select the item number 0114.
>
7. Repeat adjustment from step 3.
8. Press the key four times and back to the Display Check
x
mode.
Destination
US, Canadian, E, Mexican,
Hong Kong, Korean, Australian and
Tourist
AEP, UK and East European
Table 3-5-2. Destination Setting
Result
Decimal Hexadecimal
50 32h
30 1Eh
147 93h
40 28h
38 26h
116 74h
key on the remote
–
key on the remote
–
Setting value
Item No. 0113 Item No. 0114
20 80
A0 80
3-5-3. Other setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once and press the
select the item number 1113 and display as follows.
Display of the remote commander
113 SS**$$##
adjustment value (hexadecimal)
4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "**" on the LCD becomes "1A".
5. Press the key on the set or
X
commander to write the adjusted value. ($$ blinks and disc
mark rotates on the LCD)
6. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "20".
7. Press the key on the set or
X
commander to write the adjusted value. (## blinks and disc
mark rotates on the LCD)
8. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes "94".
9. Press the key on the set or
X
commander to write the adjusted value.
10. Press the [VOL+] key once to change the adjustment value of
"**" on the LCD into "1B".
11. Press the key on the set or
X
commander to write the adjusted value. ($$ blinks and disc
mark rotates on the LCD)
12. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "F1".
13. Press the key on the set or
X
commander to write the adjusted value. (## blinks and disc
mark rotates on the LCD)
14. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes "1A".
15. Press the key on the set or
X
commander to write the adjusted value.
16. Press the key four times and back to the Display Check
x
mode.
MZ-RH910
key five time to
>
key on the remote
–
key on the remote
–
key on the remote
–
key on the remote
–
key on the remote
–
key on the remote
–
19