Table of Contents
Related Manuals for Ryobi RA-NBS1832-S
Summary of Contents for Ryobi RA-NBS1832-S
- Page 1 RA-NBS1832-S AIRWAVE AIR BRAd NAIlER/StAplER (2 IN 1) OpERAtOR'S MANUAl ORIgINAl INStRUctIONS Important! It is essential you read the instructions in this manual before starting and operating this machine. Subject to technical modifications.
- Page 2 dEScRIptION 1. Nitto style coupler 2. No mar pad 3. Safety yoke 4. Exhaust cap 5. Air supply 6. Magazine 7. Nails 8. Staples 9. Trigger Fig. 3 10. Depth adjustment knob 11. Flat blade screwdriver 12. Jam release Fig. 1 Fig.
- Page 3 Fig. 7 Fig. 8 Fig. 9 7, 8 Fig. 10 Fig. 11...
- Page 4 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler coupler Regulator Air hose (0-8.5 bar) Fig. 12...
-
Page 5: General Safety Rules
comfortable posture while maintaining a secure footing gENERAl SAFEty RUlES and avoiding awkward or off-balanced postures. The operator should change posture during extended ■ For multiple hazards, read and understand the safety tasks, which can help avoid discomfort and fatigue. instructions before installing, operating, repairing, maintaining, changing accessories on, or working ■... -
Page 6: Additional Safety Instructions For Pneu- Matic Power Tools
INFORMAtION ON MEchANIcAl IMpAct(VIBRAtION) ■ Repairs shall be carried out only by the manufacturer's authorized agents or by other experts, having due The characteristic vibration values for the fastener driving regard to the information given in the operating tool have been determined in accordance with ISO 8662- instructions. -
Page 7: Specifications
trigger using finger pressure. flying objects. In addition, fastener driving tool is fitted with a safety yoke which enables the driving operation to be carried SyMBOlS out only after the safety yoke of the tool is pressed against a work piece, These tools are marked with an inverted triangle behind the serial number and are Safety alert... -
Page 8: Intended Use
■ Push the tool against the work surface and squeeze Air inlet size 6.35 mm (1/4”) the trigger to drive a fastener. Air hose size 9.52 mm (3/8”) ■ Do not use any additional force upon the product. Air consumption 0.76 L/cycle at 6.9 bar (100 psi) WARNINg Working pressure... -
Page 9: Operation
Under normal use conditions, the tool should be lubricated WARNINg with air tool oil before connecting the tool to an air supply. Do not attempt to modify this tool or create accessories Add air tool lubricant into the air fitting on the tool once daily with minimal use, or twice a day with heavy use. - Page 10 WARNINg WARNINg Connect the fastener driving tool to the compressed The tool’s driving mechanism may cycle when the tool air supply using suitable pressure hose equipped with is first connected to the air supply. Always connect the quick-action connectors. tool to a pressurized air supply before loading fasteners to prevent injury from unintended cycling.
-
Page 11: Setting The Air Pressure
trigger. WARNINg Check whether the fastener has been driven into the work Check the safety yoke before use. If it is deformed or piece in accordance with the requirements. cannot telescope, do not use the tool until it is replaced. ●... -
Page 12: General Maintenance
gENERAl MAINtENANcE 2. To remove a strip of fasteners from the tool, release the magazine lock and slide open the magazine. Avoid using solvents when cleaning plastic parts. Most 3. Remove the fasteners from the magazine. plastics are susceptible to damage from various types of NOtE: Always keep fingers clear of fastener track of commercial solvents and may be damaged by their use. - Page 13 against a workpiece several times. The tool must IMpORtANt! not operate. See figure 12. ● With the safety yoke not engaged on the workpiece, point the tool down and away from you and other If a filter/regulator/lubricator is not installed on the air persons, and pull the trigger several times.
-
Page 14: Troubleshooting
tROUBlEShOOtINg pROBlEM cAUSE pOSSIBlE SOlUtION Loose screws. Tighten screws. Air leak near the top of the tool or in the trigger area. Worn or damaged O-rings or seals. Install overhaul kit. Loose screws. Tighten screws. Air leak near the bottom of the tool. -
Page 15: Parts List
pARtS lISt No. Description Description Description No. Description Bolt Gun body Roll pin 2.5 x 18 Bolt M4 x 12 Deflector spring Rubber washer Magazine Orientation seat Air deflector Bolt M3 x 8 Fixed cover Orientation spring Orientation spring Guide sleeve Spring washer Roll pin 3 x 20 Steal ball... - Page 16 techtronic Industries (Australia) pty. ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia techtronic Industries New zealand ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand...