WELCOME TO THE WORLD OF Please note: * Thank you for purchasing the Parabody 909101 ST Leg Curl/Extension. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
Page 3
PART # DESCRIPTION 6697803 TOWER 6662303 LEG EXT HANDLE LEFT 6662203 LEG EXT HANDLE RIGHT 6705501 4 OD X 7" ROLLER PAD 6523401 3/4 OD X 72-3/8" GUIDE ROD 6699302 PAD SLEEVE 6700303 BENCH FRAME 6698003 LOWER CROSS SUPPORT 6698903 LEG PEDESTAL 6698603 TOWER BRACE...
Page 4
34 1/2 X 3” 1/2 X 4” 33 FIGURE 1 STEP 1: • LOOSELY assemble LOWER CROSS SUPPORT (8) to the TOWER (1) and BENCH FRAME (7) using four 1/2 X 4” BOLTS (33), four 1/2” WASHERS (40) and four 1/2” LOCK NUTS (43). See FIGURE 1. •...
Page 5
FIGURE 2 STEP 2: • SECURELY assemble the LEFT (2) and RIGHT (3) LEG EXT. HANDLES to the BENCH FRAME (7) using two 3/8 X 3-1/4” BOLTS (35), four 3/8” WASHERS (41), and two 3/8” LOCK NUTS (44). See FIGURE 2. •...
Page 6
3/8 X 1” 38 FIGURE 4 STEP 4: • SECURELY assemble SEAT PAD (15) to HINGE TABS (45) using two 3/8 X 1” BOLTS (38) and two 3/8” WASHERS (41). See FIGURE 4. • SECURELY assemble one 1/2” SPRING PIN (46) to the BENCH FRAME (7) as shown in FIGURE 4. FIGURE 5 1/2 X 6”...
Page 7
FIGURE 6 STEP 6: • SECURELY assemble BACK PAD (14) to the RIGHT & LEFT PAD SUPPORTS (12) (13) using four 3/8 X 2-3/4” BOLTS (36) and four 3/8” WASHERS (41) as shown in FIGURE 6. FIGURE 7 STEP 7: •...
Page 8
STEP 8: • Attach LEG PEDESTAL (9) to the BENCH FRAME (7) using two 3/8 X 1” BUTTON HEAD CAP SCREWS (39) and two 3/8” LOCKWASHERS (42) as shown in FIGURE 8. (NOTE: Both button head cap screws must be tightened at the same time using two allen wrenches.) FIGURE 9...
Page 9
STEP 10: • Snap two WEIGHT PLATE BUSHINGS (25) into the “PARABODY” side of all twenty WEIGHT PLATES (54) as shown in FIGURE 10. FIGURE 10 39 3/8 X 1” BTN HD 20 FIGURE 11 STEP 11: • Insert the two GUIDE RODS (5) into the base of the TOWER (1) as shown in FIGURE 11.
Page 10
STEP 12: • SECURELY assemble two 3-1/2” PULLEYS (22) to the TOWER BRACE (10) using two 3/ 8 X 2” BOLTS (37), and two 3/8” LOCK NUTS (44). See FIGURE 12. FIGURE 13 33 1/2 X 4” FIGURE 12 37 3/8 X 2” STEP 13: •...
3/8 X 1” 38 FIGURE 14 STEP 14: • Attach two 1 X 1” GLIDES (29) to the LEFT & RIGHT PAD SUPPORTS (12) (13) approximately where shown in FIGURE 14. • SECURELY assemble the CABLE (23) to the cam on the LEG PEDESTAL (9) using one 3/8 X 1” BOLT (38), one 3/8” WASHER (41), and one 3/8”...
37 3/8 X 2” FIGURE 15 STEP 15: • SECURELY assemble three 4-1/2” PULLEYS (21) to the brackets on the BENCH FRAME (7) and LOWER CROSS SUPPORT (8), using three 3/8 X 2” BOLTS (37), one 2-7/8” L-BRACKET (27), and three 3/8” LOCK NUTS (44) as shown in FIGURE 15. •...
FIGURE 16 STEP 16: • Loop the threaded end of the CABLE (23) throught the holes and around the pulleys in the TOWER BRACE (10) as shown in FIGURE 16. • Screw the treaded end of the CABLE (23) approximately 3/4” into the end of the WEIGHT STACK SHAFT (19) and tighten jam nut securely.
1/2 X 3” 34 FIGURE 17 STEP 17: • Loosen the two 1/2 X 3” BOLTS (34) holding the UPPER CROSS SUPORT (11) to the TOWER (1) as shown in FIGURE 17. FIGURE STEP 18: • Assemble FRONT SHROUD (16) over the pro- truding bolts, then assemble the REAR SHROUD (17) inside of the FRONT SHROUD (16).
TIGHTEN! TIGHTEN! FIGURE 19 STEP 19: • Securely tigten the bolts holding the FRONT (16) & REAR (17) SHROUDS. THIS CONCLUDES THE ASSEMBLY OF THE 909101 LEG CURL/EXTENSION...