Advertisement
Quick Links
BODYSMITH PROSYSTEM MAiN UNIT
093
PRODUCT ASSEMBLY
I[NSTRUCTTON, S~ETS
TOOLS I~._EQUIR.E. D FOR ASSEI~BLY
9~16 iqh'CH SOCKET
AD~ISTABLE
WRENCH
RUBBER/VL4.LLET
or
~R
REVISION: K
if you experience any problem w~th the assembly of this product, plms~ co:atact your
¯ or your PAP~,.BOD¥ Customer Ser~',i~e Representath,e at:
1-800-32g-97~4
Advertisement
Related Manuals for ParaBody 93
Summary of Contents for ParaBody 93
- Page 1 BODYSMITH PROSYSTEM MAiN UNIT PRODUCT ASSEMBLY I[NSTRUCTTON, S~ETS TOOLS I~._EQUIR.E. D FOR ASSEI~BLY 9~16 iqh’CH SOCKET AD~ISTABLE WRENCH RUBBER/VL4.LLET REVISION: K if you experience any problem w~th the assembly of this product, plms~ co:atact your ¯ or your PAP~,.BOD¥ Customer Ser~’,i~e Representath,e at: 1-800-32g-97~4...
- Page 2 093 BODYSiVfIT~ PROSYSTEM SORT AND COUNT ALL PARTS BEFORE BEGYNNING ASSEiV[BLY ~AP, D%VARE: I_TCLM NAME/DESCPJPTION .~/8 X 3-//4 IN. BOLT 3/~, X 3 IN. BOLT 3/8 X 2-3/4 IN. BOLT 3/8 X 2 IN, BOLT 3/8 X 1-3/4 IN, BOLT ...
- Page 3 09.3 BODYS1V][!TH PROSYSTE1V[ ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY W~LDM-ENTS/’PARTS: ITEM N.~dV[E/DESCR/PTION MAIN UPRIGHT WEIGHT CARP/AGE TOP UPRIGHT SUPPOR-T BOTTOM (./PPdGHT SUPPOt%T FRONT UPR.IGHT ADJUSTABLE KNEE SUPPORT LAT BAR HOLDEP. BAR- HOLDER LAT BAR..LOW ROW BAR ...
- Page 4 ¯ TIlE BODYSMITH PROSYSTEM MUST BE ASSEMBLED ON A FLAT LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. ¯ PARABODY, INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ~SSEMBLED .BY TWO PERSONS TO AVOID POSSIBLE INJURY. I~.EP ALL LOOSE FRAME -CONNECTIONS LOOSE UNTIL ~NSTRUCTED IN THE...
- Page 5 BODYSMITi-I PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (I) 1-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOP on the WEIGHT CARRIAGE. Slide WEIGHT CARRIAGE down over the REAR UPRIGHT of the MAIN UPRIC-;HT. (NOTE: MAKE SURE THAT THE WEIGHT PEG ON THE WEIGHT CAP,.RIAGE IS FACING TOWARDS TFIE FRONT OF THE MACHINE) LOOSELY attach the two (2) PULLEY MOUNT FLATS to the REAR and FROthT UPRIGHTS of the MAIN UPRIGHT, using two (2) 3//I X 3 IN.
- Page 6 BODYSI~tTU PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (1.) 3/4 X 2 IN. PAP,.AGLIDE St’RIP and one (I) 1-1/2 X2 IN. PARAGLIDE ADJUSTABLE KNEE SUPPORT as shown in (’DETAIL E) using the following Thoroughly ciean all surfaces where the PARAGLIDE Remove the paper backing from the PARAGLIDE STRIPS and firmly apply them to the shown surfaces.
- Page 7 BODYSMiTH PROSYSTEM ASSEMBLY INSTRUCTIONS To install SECONDARY CABLE (PB2559-1), start WHITE BALL under the FRONT PULLEY in the UPRIGHT. (REMOVE PULLEY FOR EASE OF INSTALLATION) Push the CABLE under the FRONT PULLEY and through the HOLE of the 1VLAIN UPRIGHT to the PULLEY on the UPRIGHT BRACE of the I~L~_IN UPRIGHT.
- Page 8 093 BODYS!Vf!TN PROSYSTEM ASSE!VLBLY INSTRUCTIONS SNAP ~OO~ ~ FASTENED ~EFO~ DOLNG EXERCISES "~ WARNING ~’ DO NOT OPERATE TIIIS IV!ACH!NE W!TI-! LAT BAR OFF SAFETY HOOKS EXCEPT DURING I~IGH PULLEY EXERCISES !!! WAR.N]:NG !:! TI:~ LAT BAR IS NOT TO BE USED FOR PULL-UPS...
- Page 9 TOP UPRIGHT SUPPORT ~ ,.3/8 LOCKWASHE:R I.AT BAR HOLE MAIN UPRI ;ERIAL .NUMBER BAR HOLDER (2) (~:E I:::~TAIL" F’) BAR HOLDER FRONT UPRIGHT...
- Page 11 3/B x 3-~,/~. BOLT (2) NUT TYP. LOCKFh’ASNER WASHER TYP. KNEE SUPPORT (SEE DETAIL NU’r (2). LOCKWASHER (2.) ~/20.D. X 1 IN BUSHING NUT (2) DETAIL’A"...
- Page 12 (5{~: DE TAI L’F" LOW ROW FOOT BRACE...