Table Of Contents - Napoleon 9600 SERIES Installation And Operating Instructions Manual

2
1.0 INTRODUCTION
2.0 SAFETY SYMBOLS AND WARNINGS
2.1 SAFETY RULES
2.2 CODES
2.3 INSTALLATION REQUIREMENTS SPECIFIC TO THE STATE OF MASSACHUSETTS FOR DIRECT VENT, MECHANICAL VENT, AND
DOMESTIC HOT WATER APPLIANCES.
3.0 FURNACE SIZING
4.0 LOCATION OF UNIT
4.1 GENERAL GUIDELINES
4.2 OTHER CONSIDERATIONS
4.3 INSTALLATION IN UPFLOW, DOWNFLOW OR HORIZONTAL POSITIONS
4.4 AIR CONDITIONING
5.0 COMBUSTIBLE CLEARANCES
6.0 DUCTWORK
6.1 DUCTWORK STEPS
7.0 VENTING AND COMBUSTION PIPING
7.1 ACCEPTABLE MATERIALS IN CANADA
7.2 ACCEPTABLE MATERIALS IN UNITED STATES
8.0 NON-DIRECT VENT FURNACE INSTALLATIONS USING INDOOR COMBUSTION AIR (ONE PIPE SYSTEM)
8.1 DETERMINING COMBUSTION AIR
8.1.1 CASE 1: FURNACE LOCATED IN A UNCONFINED SPACE
8.1.2 CASE 2: FURNACE LOCATED IN A CONFINED SPACE
8.1.3 CASE 3: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR FROM ATTIC OR CRAWL SPACE
8.1.4 CASE 4: FURNACE LOCATED IN A CONFINED SPACE, OUTDOOR AIR DUCTED HORIZONTALLY
8.1.5 CONNECTION TO FURNACE NON-DIRECT VENT
9.0 VENTING GUIDELINES
9.1 VENT TERMINATION
9.2 IN CANADA
9.3 IN UNITED STATES
9.4 FURNACE VENTING INSTALLATIONS
9.4.1 NON-DIRECT VENT INSTALLATION USING INDOOR COMBUSTION AIR (ONE PIPE SYSTEM)
9.4.2 DIRECT VENT INSTALLATION USING OUTDOOR COMBUSTION AIR (TWO PIPE SYSTEM)
9.4.3 COMBUSTION AIR
10.0 TERMINATIONS
10.1 COMBUSTION AIR
10.2 EXHAUST
10.3 CONCENTRIC VENTING KIT
10.4 CONCENTRIC VENT TERMINATION INSTALLATION INSTRUCTIONS
10.5 LOCATION
10.6 MULTIPLE VENTING
10.7 IN CANADA
10.8 IN UNITED STATES
10.9 FURNACE CONNECTION
10.9.1 ROUTING OPTIONS
10.9.2 EXHAUSTER ROTATION INSTRUCTIONS
10.9.3 PREPARATIONS FOR VENT AND DRAINING OPTION
11.0 CONDENSATE DRAINS
11 .1 DRAIN HOSE INSTALLATION
11.1.1 DRAIN PIPING
11.2 CONDENSATE NEUTRALIZERS
12.0 GAS SUPPLY AND PIPING
12.1 GAS SUPPLY
12.2 GAS PIPING
12.3 GAS INLET PRESSURE
12.4 LEAK TESTING
12.5 PURGING GAS LINES
13.0 CONVERSIONS
13.1 CONVERSION STEPS
13.2 CHECKING THE INLET GAS PRESSURE
13.3 SETTING THE MANIFOLD GAS PRESSURE
13.4 CHECKING FURNACE INPUT
14.0 ELECTRICAL SPECIFICATIONS
14.1 ELECTRICAL WIRING AND CONNECTIONS
14.2 120 FURNACE CONNECTION
15.0 LOW VOLTAGE WIRING
15.1 SINGLE STAGE THERMOSTAT
15.2 TWO STAGE THERMOSTAT
15.3 THERMOSTAT LOCATION
16.0 OPTIONAL ACCESSORIES (FIELD SUPPLIED/INSTALLED)
16.1 ELECTRIC AIR CLEANER
16.2 POWER HUMIDIFIER
16.3 EMERGENCY HEAT MODE
17.0 STARTUP PROCEDURES
17.1 TO START THE FURNACE
17.2 TO SHUT DOWN THE FURNACE
W415-0919 / 10.12.10

TABLE OF CONTENTS

3
4
5
5
8
10
11
11
12
12
13
13
14
15
15
15
16
16
17
17
17
18
19
20
20
21
22
22
23
23
23
23
24
24
24
24
24
25
25
26
26
26
29
29
30
34
34
34
35
36
36
36
37
37
37
38
38
39
40
41
41
41
42
43
43
43
43
43
43
44
44
44
44
45