Tecsun PL-360 Operation Manual
  1. Manuals
  2. Brands
  3. Tecsun Manuals
  4. Receiver
  5. PL-360
  6. Operation manual

Tecsun PL-360 Operation Manual

Fm stereo / mw / sw dsp receiver
Hide thumbs Also See for PL-360:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
TECSUN
TECSUN RADIO CO., LTD.
FACTORY: 189 GuanChang Road, DongCheng District,
DongGuan, GuangDong, P.R.China
E-mail: tecsun@on-nets.com
Website: www.tecsun.com.cn
www.tecsun.b2s.com
PL-360
FM stereo / MW / SW DSP RECEIVER
OPERATION MANUAL
TECSUN
SLEEP
PL-360
FM STEREO / MW / SW DSP RECEIVER
TECSUN RADIO CO., LTD.
TECSUN

Advertisement

Table of Contents
loading

Related Manuals for Tecsun PL-360

Summary of Contents for Tecsun PL-360

  • Page 1 TECSUN PL-360 FM stereo / MW / SW DSP RECEIVER OPERATION MANUAL TECSUN SLEEP TECSUN RADIO CO., LTD. FACTORY: 189 GuanChang Road, DongCheng District, PL-360 FM STEREO / MW / SW DSP RECEIVER DongGuan, GuangDong, P.R.China E-mail: tecsun@on-nets.com Website: www.tecsun.com.cn TECSUN RADIO CO., LTD.

  • Page 2: Functional Block Diagram

    SPECIFICATIONS PL-360 Functional Block Diagram PL-360 is using DSP si4734 Microchips (from Silicon Labs in 1. Frequency range USA) to digitalize the analog AM/FM broadcasting signal base 87~108 MHz on the modern software technology and radio principles. It can highly improve on radio's sensitivity, selectivity, S/N ratio and Japan 76~108 MHz anti-interference.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS CONTROL LOCATIONS........... 2 QUESTIONS ANSWERS SOLUTIONS LCD DISPLAY..............4 When the alarm -Did not set the -Preset your alarm TURN ON / OFFTHE RADIO ..........5 activated (alarm proper radio station station properly by radio), there is for the alarm. (see the above TUNE INTO STATIONS...

  • Page 4: Control Locations

    [FM SET] button again to select 76~108MHz. Received very -USA is using -Turn off the radio poor AM in USA. 10kHz step for AM. press the [9/10kHz] button to select 10kHz. PL-360 FM STEREO / MW / SW DSP RECEIVER...

  • Page 5: Turn Off The Alarm

    IMPORTANT MATTERS FOR USING BATTERIES 1. If no battery has been installed inside for long time, clock Power on/off of radio would stop to work. However, pre-stored frequencies are still kept. Clock would work again after Multifunctional tuning knob new batteries being re-installed inside. 2.

  • Page 6: Lcd Display

    LCD DISPLAY USING THE INTELLIGENT CHARGING FUNCTION With radio off, install 3 x UM3 (AA) rechargeable batteries 1 2 3 4 and then press & hold the [ ] key with " " & " " displays to activate the built in charging function. SLEEP Temp.

  • Page 7: Turn On / Offthe Radio

    The battery compartment is located on the back of the Attach the clip on type “external FM/SW antenna” to the PL-360. To remove the battery compartment cover, apply Telescopic antenna of PL360, then extend the wire and thumb pressure and slide it towards the bottom of the hang on another end to the window or wall to enhance the radio.

  • Page 8: Tune Into Stations

    TUNE INTO STATIONS Short press [POWER] button to turn on your radio, then Turn ON/OFF charging function & exchange battery select your desired band by short pressing the [FM], [MW], consumption display SW [ ] or [ ] button. In case of receiving FM/SW Press &...

  • Page 9: Manual Tuning

    SYSTEM SETTING MW station: It is recommendable to perform the ETM Frequency range setting for FM function during day time as well as night time, because Turn off the radio, long press [FM] button, until 87.5-108MHz, there usually are more stations that start broadcasting at 76-108MHz, or 87-108MHz appears in the display.
  • Page 10 TURN OFF THE ALARM When the radio is turned on by the alarm function with radio, Method 4: AUTO BROWSE MEMORY you can short press [POWER] button to continue listening 1. Turn on the radio, short press radio afterwards. the [VM] button with memory Short press [POWER] again to turn off the radio.

  • Page 11: Working With Memories

    SETTING THE CLOCK WORKING WITH MEMORIES There are total 450 preset memories within PL-360. For FM 1. Long press the [TIME] button until you see the hour and LW, each band has 100 preset memories; and 250 flashing. Rotate the [TUNING] knob to set the correct hour, then short press the [TIME] button and notice the preset memories for SW.

  • Page 12: Manually Storing Station

    Method 2: SEMI AUTO-DELETE MEMORY Method 2: MANUALLY STORING STATION In VM mode, long press the [VM] button to activate the 1. Tune to your desired station, press the [MEM.] button Auto-Browse function of memory. Once previewing your once and notice the PRESET number flashing in the unwanted station, simply press the [DEL.] button with upper right corner of the display.

Table of Contents