Table of Contents
Advertisement
E N G L I SH
EC-Declaration of Conformity
D25012, D25013
D
WALT declares that these products described
E
under "technical data" have been designed in
compliance with:
98/37/EEC (until Dec. 28, 2009), 2006/42/EC (from
Dec. 29, 2009), 2004/108/EC, EN 55014-1, EN
55014-2, EN 61000-3-2, EN 61000-3-3, EN
60745-1, EN 60745-2-6.
For more information, please contact D
following address or refer to the back of the manual.
The undersigned is responsible for compilation of
the technical file and makes this declaration on
behalf of D
WALT.
E
Horst Grossmann
Vice President Engineering and Product
Development
D
WALT, Richard-Klinger-Straße 11,
E
D-65510, Idstein, Germany
05.05.2009
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
Keep work area clean and well lit.
a)
Cluttered or dark areas invite accidents.
Do not operate power tools in
b)
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which
may ignite the dust or fumes.
Keep children and bystanders away
c)
while operating a power tool.
Distractions can cause you to lose control.
4
2) ELECTRICAL SAFETY
a)
b)
c)
WALT at the
E
d)
e)
f)
3) PERSONAL SAFETY
a)
b)
c)
d)
Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
Stay alert, watch what you are doing
and use common sense when
operating a power tool. Do not use a
power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
Remove any adjusting key or wrench
before turning the power tool on.
Awrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
Advertisement
Table of Contents
