1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Rotary Hammer
  5. D25052-XE
  6. Instruction manual

DeWalt D25052-XE Instruction Manual

Sub-compact 20mm sds plus rotary hammer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
D25052-XE
SUB-COMPACT 20MM SDS PLUS ROTARY HAMMER

Advertisement

Table of Contents
loading

Related Manuals for DeWalt D25052-XE

Summary of Contents for DeWalt D25052-XE

  • Page 1 INSTRUCTION MANUAL D25052-XE SUB-COMPACT 20MM SDS PLUS ROTARY HAMMER...

  • Page 3: Definitions: Safety Guidelines

    D25052 Definitions: Safety Guidelines (sound pressure) dB(A) The definitions below describe the level of severity for each signal (sound pressure uncertainty) dB(A) word. Please read the manual and pay attention to these symbols. (sound power) dB(A) DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

  • Page 4: Safety Instructions For Power Tools

    SAFETY INSTRUCTIONS FOR POWER TOOLS tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or When using power tools, always observe the safety regulations applicable in your unplugging the power tool. Keep cord away from heat, oil, sharp edges country to reduce the risk of fire, electric shock and personal injury.

  • Page 5: Electrical Safety

    4) POWER TOOL USE AND CARE tool is double insulated, therefore no earth wire is required. a) Do not force the power tool. Use the correct power tool for your • Young children and the infirm. This appliance is not intended for use by young application.
  • Page 6 control. Breaking through or encountering hard materials such as re-bar may be WARNING: ALWAYS wear approved protective safety equipment complying with hazardous as well. Tighten the side handle securely before use. the following standards: • The hammer is only for light chiselling applications. •...

  • Page 7: Components (Fig. 1)

    • The label on your tool may include the following symbols. The symbols and their FIG. 1 definitions are as follows: V ......volts A ......amperes Hz ....hertz W ......watts min ....minutes or AC ....alternating current or DC ..direct current or AC/DC ..alternating or ....Class I Construction ......direct current (grounded)

  • Page 8: Assembly And Adjustments

    ASSEMBLY AND ADJUSTMENTS VARIABLE SPEED The variable speed trigger switch (A) permits speed control. The farther the trigger WARNING: To reduce the risk of serious personal injury, turn tool off and switch is depressed, the higher the speed of the drill. disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories.

  • Page 9: Operation

    WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in DRILL-ONLY MODE anticipation of a sudden reaction. To use drill-only mode, turn the mode selector (F) so the yellow arrow points to the Proper hand position requires one hand on side handle (C) as shown, with the other corresponding symbol as shown.
  • Page 10 WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is DRILLING IN METAL anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to An SDS Plus ® to round shank adaptor chuck is required. Ensure that tool is in drill- prevent damage to the material.

  • Page 11: Maintenance

    DEPTH ROD (FIG. 5) Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once TO ADJUST THE DEPTH ROD a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye 1.
  • Page 14 Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (OCT13) Part No. N312982 D25052-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

Table of Contents