Supporting Documentation - Mitel 5320e Installation Manual

Important Safety Instructions and Precautions
WARNING:DO NOT CONNECT DIRECTLY TO THE PUBLIC SWITCHED
TELEPHONE NETWORK (PSTN). ANY CONNECTION OF THIS PHONE
TO AN OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION,
ANY OTHER EXPOSED PLANT APPLICATION, OR TO ANY EQUIPMENT
OTHER THAN THE INTENDED APPLICATION MAY RESULT IN A SAFETY
HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT
DAMAGE. "EXPOSED PLANT" MEANS WHERE ANY PORTION OF THE
CIRCUIT IS SUBJECT TO ACCIDENTAL CONTACT WITH ELECTRIC
LIGHTING OR POWER CONDUCTORS OPERATING AT A VOLTAGE
EXCEEDING 300 V BETWEEN CONDUCTORS OR IS SUBJECT TO
LIGHTNING STRIKES.
WARNING:THE SOCKET OUTLET, IF USED, SHALL BE LOCATED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE BY THE USER.
WARNING:USE MITEL APPROVED POWER ADAPTER PART NUMBER
51015131.
NOTE: SOME IP PHONES DO NOT REQUIRE AN AC POWER ADAPTER. IF
POWER OVER THE LAN IS AVAILABLE, IT SHALL BE COMPLIANT WITH
IEEE 802.3af.
WARNING:THE HANDSET SUPPLIED WITH THE IP PHONE IS NOT
CERTIFIED FOR USE WITH ANY OTHER PHONE. USE OF THE
HANDSET WITH ANY OTHER PHONE MAY HAVE THE POTENTIAL TO
CAUSE HEARING LOSS IN THE EVENT OF A LIGHTNING STRIKE ON
THE OUTSIDE PLANT WIRING.
When using your phone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons, including
the following:
• Do not use this product near water, for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.
• Avoid using a phone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
• Do not use the phone to report a gas leak in the vicinity of a leak.
Maintenance and Repair: There are no user serviceable parts inside the
phones. For repairs, return the phone to an authorized Mitel dealer.
These notices may appear on the product or in the technical documentation:
Danger indicates an imminently hazardous situation which, if not
DANGER
avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not
WARNING
avoided, could result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not
CAUTION avoided, may result in minor or moderate injury and/or damage to the
equipment or property.
This symbol may appear on the product:
The exclamation point within an equilateral triangle indicates that important
operating and maintenance (servicing) instructions are included in the
!
literature accompanying the product.
2
Description
Mitel 5320e/5330e/5340e IP phones are supported by:
• Mitel Communications Director (MCD) Release 5.0 and later software.
• SX-200 IP Communications Platform (ICP) Release 4.0 (UR3) and later
software.
• 5000 Communications Platform Release 5.1 and later software.
5320e/5330e/5340e IP phones are LAN-powered.

Supporting Documentation

To access phone- and system-specific documentation:
1. In your browser, go to http://edocs.mitel.com.
2. Click End User Documents, and then select PDF Guides and Online
Help from the drop-down menu.
3. Navigate to 5300 Series-Mitel Communications Director.
Installing a 5320e/5330e/5340e IP Phone (See Figure
NOTE: The illustrations on the front page show a 5340e IP Phone; the
following procedures also apply to the 5320e and 5330e IP Phones.
It is easiest to connect the cables to your phone after you have attached the
mounting base unit to the phone.
Before installing your phone, ensure that you are familiar with the following
powering options:
• An IEEE 802.3af LAN-powered jack provides power to the phone via a
LAN cable. (The phone receives ethernet signals and power through the
same cable.) To install, see Steps
• An Ethernet power adapter provides power to the phone via a LAN cable.
The Ethernet power adapter is connected to the LAN via a separate LAN
cable connected to a jack. (The phone receives ethernet signals and
power through the same cable.) To install, see Steps
NOTE: Use only qualified Mitel-supplied Ethernet adapters.

Thread the LAN cable plug through the slot on the back of the installed base
unit and plug it into the LAN port on the back of the phone.
NOTE: If you are wall-mounting your phone, do not thread the LAN cable
through the base unit slot—connect the cable directly from the LAN port on
the phone to the jack on the wall.

Plug the other end of the LAN cable into one of the following:
• the phone port of an Ethernet power adapter. Then, connect the
Ethernet adapter to the LAN using a separate LAN cable, and plug the
power adapter into an AC power outlet.
or
• a LAN-powered jack.
NOTE:The LAN-powered phone provides power to any attached
peripheral.

Plug the handset cord into the handset port and thread it through one of the
slots on either side of the base unit.

(Optional) Plug the telephony headset cord into the headset port on the
back of the phone. Thread the headset cord through one of the slots on
either side of the base unit, as shown for the handset cord in

To register an installed phone to MiNET mode, enter a valid PIN, and then
press (HOLD) to register the phone.

After the date and time appear on the display, proceed with the next step.

For 3300 ICP MiNET deployments, you can connect a PC to the PC port on
the back of the phone. If desired, thread the PC cable through the slot on the
back of the installed base unit, as shown for the LAN cable in
 .
and
 .
and

above.

A
)
above.