Install The Door Control - Chamberlain 3500 - 1/2HP Series Owner's Manual

Installation Step 6

Install the Door Control

• Strip 1/4" of insulation from one end of the bell
wire; connect the wire to the two screw terminals
on the back of the door control by color: white to 2
and white/red to 1.
• Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all
moving parts of the door and door hardware.
Fasten the Lighted Door Control Button securely
with 6ABx1-1/2" screws. The Multi-Function Door
Control Panel uses 6ABx1" screws. If installing
into drywall, drill 5/32" holes and use the anchors
provided.
• Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
• Receiver terminal screws and the antenna are
located on the back panel of the opener. Position
the antenna wire as shown.
• Then connect the bell wire to the opener terminal
screws: white to 2 and white/red to 1.
• Remember to affix the User Safety Instruction
label to the wall near the door control, and the
Maintenance Instruction Label in a prominent
location on the inside of the garage door.
If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time) use tacks
to secure the label alongside the door control.
Page 32 explains how to operate the opener using
the door control and the Lock and Light features
available on the Multi-Function Door Control Panel.
Hardware Shown Actual Size
6ABx1" Screw
Multi-Function Door Control Panel
6ABx1-1/2" Screw
Lighted Door Control Button
Lighted
Door Control
Button
Dry Wall Anchors
Insulated Staples
2-Conductor
Bell Wire
Lock Button
LO C K
LI G H T
Light Button
Door Control
Push Bar
Multi-Function
Door Control Panel
18
WARNING
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the Door Control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control transmitter(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it
clearly, and there are no obstructions to door
travel.
Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full open position but will not return to the
close position until the sensor beam is
connected and properly aligned.
See Safety Reversing Sensor Instructions
beginning on page 21.
Outside Keylock Accessory Connections:
To opener terminal screws: white to 2; white/red to 1
Series 5100 and 3100
2-Conductor
Bell Wire
-2
Lighted Door
-1
Control Button
Terminal Screws
TO PROGRAM RECEIVER CODE
FOR EACH REMOTE CONTROL
1. Press and HOLD remote control
transmitter push button.
2. Press receiver code button. The opener
light will flash once.
3. Release transmnitter button. Opener
has learned code.
TO ERASE ALL RECEIVER CODES
1. Press and HOLD receiver code button.
Green indicator light alongside will turn
ON.
2. When light turns OFF (about 6
seconds) ALL codes are erased from
opener memory.
Back Panel
of Opener
Multi-function
Door Control Panel
2-Conductor
Terminal Screws
Bell Wire
RE D
WH ITE
-1
-2
Opener
Terminal
Screws
1 2 3
9 1 9 1
7 3 7 3
5 5
KG
KG
This device complies
with FCC Rules Part
15. Operation of this
device is subject to the
following conditions:
1. This device may
AVERTISSEMENT: Pour réduire les risques de
not cause harmful
blessures mortelles par happement, après tout
interference. 2. This réglage de la force de déclenchement ou des
device must accept seuils de fin de course s'assurer que le sens de
la course s'inverse lorsque la porte entre en
any interference
contact avec un object de 13 mm (1 po) de
that may be received,
hauteur (ou un madrier de 2 x 4 de section, à
including interference plat) posé sur le sol. Effectuer les reglages
that may cause selon les procédures décrites dans la notice.
undesired operation. PART NO: Nº DE PIÈCE:
Sears Roebuck & Co. D.O.C. CERT. NO. DATE:
Sears Canada Inc., Toronto
Assembled in Mexico - Assemblé du Mexique
M.D.C. CERT. NO. 132C2105-1
PAT. #RE29,525; 4,750,201; 4,806,930 Other Patents Pending.
Antenna