Table of Contents
Advertisement
Off Codes
The display shows the word "OFF" to inform
the customer the machine is out of service. If
money is added to the machine, it will be lost.
Refer to the "Off Codes" table.
DISPLAY
Service person placed machine out of service.
See
MANUAL OUT OF SERVICE
Machine has been set to be unavailable for
customer use by means of one of the three owner
'special' prices. See SP 1, SP 2 and SP 3 (special
price) on page 6-4.
No money device is enabled during machine setup.
Please enable Card (SMART Card). See
SETTINGS.
The setup may be requesting a coindrop. See
OWNER SETTINGS.
An error is occurring with the auxiliary device, such
as a Smart Card unit not plugged into connector of
control board. (The setting is enabled but no Smart
Card unit is installed.) See
Lid was not opened between end of cycle and next
spin. Run service routine to reset. See
on page 6-1.
ROUTINE
TIME AND DATE CLOCK
The time and date are not set at the factory.
The electronic control uses a battery to run the
clock. If the wire harness at connector P2 is
unplugged, the battery is disconnected and the
time and date must be reset. The battery has a
life of approximately ten years.
ADDITIONAL INFORMATION
Additional information about the machine's
performance, such as when a fill time was too
long or when the AC power was turned off, is
available when gathering data via the Palm
handheld. For more information on this fea-
ture, see ADVANTECH
Products Software User's Manual, # 8524743.
OWNER SETTINGS
1. Perform all steps under "Access Mode" on
page 6-1.
2. Push and release keypad position 1 (HOT).
3. Keypads are now re-mapped for navigating
the settings as follows:
EXPLANATION
section.
OWNER
OWNER SETTINGS.
SERVICE
Commercial Laundry
KEYPAD
HOT
1
up
WARM
2
down
COLD
select
3
NORMAL
—
4
GENTLE
—
5
6
exit
(hidden)
4. When an item on the list is selected, the
current setting is displayed. To change a
setting, use the keypads as follows:
KEYPAD
(+)
HOT
1
increase
WARM
(–)
2
decrease
COLD
—
3
NORMAL
—
4
GENTLE
—
5
6
accept
(hidden)
5. To accept the displayed setting, press key-
pad #6, and the program will return to the
OWNER SETTINGS menu.
6. After all changes to the OWNER SET-
TINGS are complete, press keypad #6 twice
to exit the program. The display returns to
the vend-price.
OWNER SETTINGS TABLE
DISPLAY
DESCRIPTION
CYCLE PRICE
—
CALENDAR YEAR
CALENDAR DATE
—
TIME
—
Table Continued on the next page.
6-3
NAVIGATING OWNER SETTINGS
Move up to the preceding item on the list.
Refer to the
OWNER SET TINGS
Move down to the next item on the list.
Refer to the
OWNER SET TINGS
Select an item to view the current setting.
Refer to the
OWNER SET TINGS
no function
no function
Exit
program. Display
OWNER SET TINGS
returns to the cycle count.
CHANGING OWNER SETTINGS
Increase the setting value. Push and hold the
keypad for fast increase. Refer to the
table.
SETTINGS
Decrease the setting value. Push and hold the
keypad for fast decrease. Refer to the
table.
SETTINGS
no function
no function
no function
Accept the new setting value. Display returns
to
list.
OWNER SETTINGS
Default
Setting
0.75
$ dollars
2000
1.1
1 to 12 months
month and day
(Jan. 1)
0.00
24-hour clock
(hours.minutes)
table.
table.
table.
OWNER
OWNER
Value
Range
0.00 to 100.00
2000 to 2030
1 to 31 days
0.00 to 23.59
Advertisement
Table of Contents
