Table of Contents
Advertisement
CAUTIONS
Symbols in this manual
To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are
classified as explained below. Be sure you understand the meaning of the symbols when reading the manual.
CAUTION!
Meaning of the symbols
HOT
Handling precautions
If you notice smoke, a strange odor, or other abnormality, do not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power plug from the power outlet.
Contact your dealer or nearest TOSHIBA Service Department.
Do not use a flammable spray to clean the machine.
If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, fire or
electrical shock may result.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to the machine.
Do not remove the machine casing.
High-voltage parts inside the machine may cause electrical shock.
Do not place a container of water or other liquid, or a metal object that might fall inside, on the machine.
If the liquid spills or the object falls into the machine, fire or electrical shock may result.
If a thunder storm begins, switch off the main power and remove the power plug from the outlet to
prevent electrical shock and fire due to lightning.
The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call
up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, TOSHIBA TEC Corporation bears no responsibility for any damages or loss due to the loss of stored document data.
Laser information
Wave length
788 nm +12nm / -13nm
e-STUDIO907:
Normal paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7mm
Heavy paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7 mm
Pulse times
e-STUDIO1057/1207:
Normal paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm
Heavy paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm
Output power
Max 2.5 mW (LD1+LD2+LD3+LD4)
PINCH POINT
PROHIBITED
KEEP CLEAR
ACTIONS
WARNING
Indicates a risk of death or serious injury.
DO NOT
MANDATORY
DISASSEMBLE
ACTIONS
WARNING
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine. Do not install the machine in a location that will block
the ventilation ports.
Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of fire.
The fusing unit and paper exit area are hot. When removing a misfeed, do not touch
the fusing unit and paper exit area. Take care not to burn yourself.
When loading paper, removing a misfeed, performing maintenance,
closing the front and side covers, and inserting and removing trays, take
care that your fingers are not pinched.
Caution
„
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007)
SAFETY PRECAUTIONS
„
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This
means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by
inserting wedges or other items into switch slots.
CAUTION
Indicates a risk of human injury or property
damage.
5
Hide quick links:
Advertisement
Table of Contents
