Page 1
SH3741/SH4241 LCD Display TV Tuner Box and Remote Control Installation and Operation Guide...
Page 2
Disclaimer This company makes no representations or warranties, either expressed or implied, with respect to the contents of this document. This company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.
Table of Contents Package contents ............. 1 Installing the TV tuner box ........1 Important safety precautions ........... 1 Installing the TV tuner box ..........1 Activate the remote control ........4 Installing batteries ............4 Battery safety notice ............4 Getting to know the remote control .......
Page 4
On-Screen Display (OSD) menu ......14 OSD structure ..............14 Navigating the OSD menu ..........15 Operations in the OSD menu ........15 Audio menu ...............16 Setting up Personal EQ Mode ........17 Picture menu ..............18 Adjusting the contrast ..........19 Adjusting the brightness ..........19 Setting up Personal Picture mode .......19 Senseye menu ..............20 Window menu ..............21...
Package contents Check the package to see if all the following items are included. If any item is missing or damaged, contact your place of purchase immediately and notify them of the discrepancy. Screw × 1 TV tuner box × 1 Installation and operation guide ×...
Page 6
2. Remove the screw that secures the metal box in the TV tuner box slot using a suitable screwdriver. 3. Use the screwdriver to remove the metal box from the slot and keep it in a safe place. 4. Remove the protective film on the TV tuner box and then insert it into the slot.
Page 7
6. Use the supplied screw and a suitable screwdriver to secure the TV tuner box on the display. 7. Connect the cable TV or aerial antenna cable to the TV cable connector on the TV tuner box. Follow the instructions of "Searching and storing TV channels"...
Activate the remote control Installing batteries 1. Turn the remote control to reveal its back side, and open the lid of the battery compartment. 2. Insert the batteries (supplied) ensuring that the positive and negative marked battery terminals match the (+) and (-) marks in the battery compartment.
Getting to know the remote control 1. Power/standby Press this button to power the display on or put it to standby mode. See "Power on, off and standby" on page 2. 數位電視 (DTV) Press this button to directly switch to the digital TV mode and view digital TV channels (A separate DTV tuner is required to use this function).
Page 10
12. Red button In DTV mode, press this button to execute the function as indicated by the red color in the menu (A separate DTV tuner is required to use this function). 13. Green button In DTV mode, press this button to execute the function as indicated by the green color in the menu (A separate DTV tuner is required to use this function).
Page 11
/ / / buttons When the OSD menu displays on-screen: • Press to select settings. • Press to adjust settings. "Navigating the OSD menu" on page 25. 回上頁 (Back) When operating in the OSD menu, press this button to return to the previous menu level. See "Navigating the OSD menu"...
Using the remote control • Point and aim the top front of the remote control directly at the display when pressing the buttons. • The remote control must be held at an angle within 30 degrees of the display's 6 meters remote control sensor window to function correctly.
• These options will only appear when corresponding signals are connected to the display. • If both Composite Video (AV) and S-Video signals are connected to the AV3 input at the same time, only S-Video input will be displayed. If you wish to view the Composite Video (AV) input in such case, remove the S-Video connection temporarily.
• To select a triple-digit channel, press on the remote control followed by the rest of the digits. within 3 seconds For example, to select channel 120, press , and then press on the remote control. Changing channels sequentially Press 頻道/換頁...
before expiration in the Sleep Timer item in the Setup menu (See "Sleep Timer" on page 23). 1 minute before the expiration of the set time, a message will display on-screen as a reminder. You can press any button on the remote control to reset the sleep timer and the display will remain on.
• To change the position of the sub picture on the screen, press or on the remote control. • To select audio from the main or sub picture, see "PIP Audio" on page The table below shows the availability of the PIP function under different Video and Graphic signal input combinations for the Main and Sub pictures.
Stretches a 4:3 image to 16:9 aspect proportions and enlarges the resultant image on the screen. You can press 16:9 Adj. (Not on the remote control to pan the recommended) (Adjust) enlarged image. Recommended for use when viewing video sources which are in 4:3 aspect such as analog TV input.
Navigating the OSD menu You can use the On-Screen Display (OSD) menu to adjust the settings on your display. To display the OSD menu, press 目錄 (Menu) on the remote control. Audio Picture Senseye Setup Window Operations in the OSD menu •...
Audio Audio menu Volume Balance The available menu items are Sound Type Stereo dependent on the input source Steady Sound being selected. The illustration is Surround for reference only. Speaker Out Advanced Audio Settings > Item Function Operation Range Adjusts the volume level of Press to increase or Volume...
Adjusts treble tones for the Treble Personal EQ Mode. Adjusts mid-treble tones for Mid Treble the Personal EQ Mode. Adjusts mid tones for the Press to make Middle -12 to 12 adjustment. Personal EQ Mode. Adjusts mid-bass tones for Mid Bass the Personal EQ Mode.
Picture Picture Mode Personal Picture menu Contrast Brightness The available menu items are Color dependent on the input source being selected. The illustration is Sharpness for reference only. Color TEMP. Normal NTSC Tint NTSC Setup 7.5 IRE Item Function Operation Range Provides complete preferred setups adjusted for color, contrast,...
Adjusts color tint in NTSC video. Press for redder NTSC Tint tones, 0 to 64 This option is only available for greener tones. NTSC video sources. Sets up the NTSC video display format to match that of the input NTSC video input from other •...
Senseye menu Color Style Color 1 The available menu items are Gamma Style Gamma 1 dependent on the input source being selected. The illustration is for reference only. Noise Reduction Item Function Operation Range • Color 1 • Color 2 Color Style •...
Window menu Window The available menu items are Main Input dependent on the input source being selected. The illustration is Sub Input for reference only. PIP Audio Main Item Function Operation Range • Off Display Video and Graphic Full screen images simultaneously in Picture-In-Picture (PIP) mode.
TV menu TV/CATV The available menu items are Channel +/- Added dependent on the input source being selected. The illustration is Favorite Channels for reference only. Auto Program Item Function Operation Range • TV Select TV or cable TV/CATV system mode. •...
Setup Setup menu Language English Backlight Normal The available menu items are Sleep Timer dependent on the input source being selected. The illustration is for reference only. HDMI/DVI Input Reset All Settings Item Function Operation Range • English Select your desired language for Language the OSD menu.