EverFocus ECOR264-4X1 User Manual
  1. Manuals
  2. Brands
  3. EverFocus Manuals
  4. DVR
  5. ECOR264-4X1
  6. User manual

EverFocus ECOR264-4X1 User Manual

Everfocus ecor264-4x1; ecor264-9x1; ecor264-16x1 dvr
Hide thumbs Also See for ECOR264-4X1:
Table of Contents

Advertisement

Quick Links

User Manual
E
E
E
E
E
E
C
O
R
2
6
C
O
R
2
6
C
O
R
2
6
C
O
R
2
6
C
O
R
2
6
C
O
R
2
6
4
-
4
X
1
4
-
4
X
1
4
-
9
X
1
4
-
9
X
1
4
-
1
6
X
1
4
-
1
6
X
1
D
V
R
D
V
R
D
V
R
D
V
R
D
V
R
D
V
R

Advertisement

Table of Contents
loading

Related Manuals for EverFocus ECOR264-4X1

Summary of Contents for EverFocus ECOR264-4X1

  • Page 1 User Manual...

  • Page 2: Front Panel

    1.4 FRONT PANEL Your primary interaction with your new DVR will be through the Front Panel buttons and their corresponding buttons on the included IR Remote Control. Take a moment to learn where the keys are as the remainder of the manual will refer to them often. Figure 1-1 Front Panel Remote Control Receiver: Receiver for IR remote control.
  • Page 3 View: Press this key to switch between 4x, PiP (Picture In Picture),full screen, 9x, 10x, 13x and 16x. Note: PIP display is not available in playback mode. SEQ: Press this key to enter the auto sequential switching mode. The sequence dwell time can be set in “Display Setting”...

  • Page 4: Mouse And Front Panel Operation

    Chapter 2 MOUSE AND FRONT PANEL OPERATION ECOR264 DVRs support multiple sources to control the DVR. It can be controlled with a mouse, the front panel, an EKB500, and the handheld IR remote control. This chapter will cover the basic operation using the mouse and the front panel buttons. 2.1 GENERAL USB MOUSE OPERATION 2.1.1 How to select a channel / Enable audio 1.

  • Page 5: Operation In The Configuration Menus

    2.1.3 Operation in the Configuration Menus Click on the icon to access the Configuration Menu. The Configuration menu screens (shown in Figure 2-2 OSD Menu) are divided into 3 main sections. Figure 2-2 OSD Menu 1. In section 1, there are ten setup options available. Move the mouse over an icon and click to select it. 2.
  • Page 6 Button: Click the button to execute the function. Bar: Click and hold on the bar to adjust the set point Left or Right. * Note about on-screen keyboard: Click on a button to input that character. The buttons on the right and bottom have the following functions: Space Enter a space Caps...

  • Page 7: General Front Panel Operation

    2.2 General Front Panel Operation 2.2.1 How to select a channel / Enable audio 1. In a view consisting of more than one channel, press the arrow keys (Up/Down/Right/Left) to scroll through each channel that is displayed. The selected channel will be highlighted by white frame. Pressing the “left”...
  • Page 8 Figure 2-3 OSD Menu 1. In section 1, there are ten setup options available. Use arrow keys to highlight an icon and press “Enter” to select it. 2. In section 2, the main choices for the selected icon will be displayed. Use Up/Down arrow keys to highlight a choice and press “Enter”...
  • Page 9 Bar: Press “Enter” key to activate the slider, then use arrow keys to adjust the setting. Press “Enter” again to finalize the changes. * Note about on-screen keyboard: Use the arrow buttons to highlight each character and press the “Enter” key on the front panel to input the selected characters.

  • Page 10: General Dvr Operations

    Chapter 3. GENERAL DVR OPERATIONS This chapter introduces the operations on major functions including playback, layout change, sequence, triplex operations, copy, and search. 3.1 RECORD By default, the DVR will always be in record mode. When the DVR is turned on, it will start to record. The exceptions are: 1.

  • Page 11: Select Camera Operation

    + To input password by mouse: click the password field to bring up the on-screen keyboard (see Figure 3-2 On-screen Keyboard). Click on each button to input the desired characters for the password. When finished, click “Done” on the on-screen keyboard to confirm the password. + To input password using front panel: use the arrow keys to select the password field, then press the “Enter”...
  • Page 12 3.5 PLAYBACK The playback bar is the fastest way to show video from the exact time which users want to see. The playback bar allows a user to see both a time line and the current playback indicator. The user can then click the time line to move the indicator to the position which they want to see.

  • Page 13: General Ptz Control

    L4: Entire time bar is 10 minutes. L5: Entire time bar is 1 minute. 11. Express copy: Press to start express copy when camera during playback (only one camera) 12. Playback speed indicator 13. Press “X” to close the playback bar. 14.

  • Page 14: Express Control Of Ptz

    10. Pattern Operation (Pattern is the “0” Tour in Everfocus and Pelco PTZ cameras) a. Click “Pattern” button 11. Steps to run a tour a. Click “Tour” button b. Click the number of the desired tour c. Click “Go” button 12.
  • Page 15 Figure 3-3 Express Control PTZ The screen is divided into a 4x4 grid. The function of each section is defined as below: • 1: PTZ pan/tilt left and up • 2, 3: PTZ tilt up • 4: PTZ pan/tilt right and up •...

  • Page 16: Bring A Camera To Full Screen Mode

    3.7 LAYOUT The ECOR264 DVR has several display modes available, depending on the number of cameras the DVR supports. The different available layouts for a 16 camera model are shown below: NOTE: PIP display is not available in Playback mode The first three layouts are available on all models;...
  • Page 17 3.9 DISPLAY Press the Display button on the menu by using the mouse or selecting this icon with the front panel keys and pressing ‘Enter’. Pressing/clicking cycles through the four OSD formats: 1. Press to show camera information. Please see the following table for camera information icons. Recording Playback Fast forward...
  • Page 18 3. Right-click to bring up the menu bar and click button. Or, press the ZOOM button on the front panel. 4. When in ZOOM mode, the mouse cursor will change to a different icon in different areas of the screen. Or, use the arrow keys to bring a different portion of the magnified image into view.

  • Page 19: Time Search

    3.12 SEARCH By mouse: Right-click to bring up the menu bar and click to enter Search Menu. By front panel: Press ”Search” key to enter Search Menu directly. 3.12.1 Time Search Figure 3-5 Search Menu – Time Search Play From: Select the time to begin the search by choosing the Date and Time. Click on the “Play”...

  • Page 20: Event Search

    3.12.2 Event Search Figure 3-6 Search Menu – Event Search From: Select starting date and time To: Select ending date and time. Camera: Select which cameras to include in the search. Event: Select which event type(s) to search for. Choose from Alarm, Motion or Video Loss. Click on the “Search”...

  • Page 21: Smart Search

    Prev Page: Go to previous page Next Page: Go to next page Play: Playback selected item Copy: Copy selected item 3.12.3 Smart Search Smart Search allows the review of a segment of the recorded video from individual cameras to detect motion in an area specified at the time of the search.
  • Page 22 Camera: Select which cameras to review. Grid Setting: Press Grid Setting button to open the motion grid setup window. Edit Motion Grid: Press this button to edit the motion grid (See Figure 4-5 Camera Menu – Motion Grid Setting ). Set All: Press this button to select the entire area.
  • Page 23 Click on the “Search” button to start searching. The search results will be shown as a list of events. Prev Page: Go to previous page Next Page: Go to next page Play: Playback selected item Copy: Copy selected item...

  • Page 24: Snapshot Search

    3.12.4 Snapshot Search Snapshot Search shows snapshots of the specified interval, it helps users to quickly find the interested scene. Figure 3-8 Search Menu – Snapshot Search Result Type: Select result type. Search Date: Select search date and time Search Direction: Select search direction, either forward or backward. Search Camera: Select which camera to be searched.
  • Page 25 Figure 3-8 Search Menu – Snapshot Search result...
  • Page 26 3.13 COPY To bring up Copy menu: By mouse: Right-click to bring up the menu bar and click on to enter Copy Menu. By front panel: Press the “Copy” key to enter Copy Menu directly. Figure 3-10 Copy Menu Camera: Select which cameras will be archived. Choose “Select All” to select all the cameras. Player: Check the box to include the ePlayer program as part of the copy (recommended).
  • Page 27 3.14 LOGOUT Right-click to bring up the menu bar and click the button to bring up the Logout Confirmation window (see Figure 3-11). Figure 3-11 Logout Confirmation window Press “Yes” button when you are ready to logout from the system. You will need to login again before accessing any other configuration options.

This manual is also suitable for:

Ecor264-16x1Ecor264-9x1

Table of Contents