Cub Cadet BC2090 Operator's Manual page 8

OPERATING THE EZ-LINK™ SYSTEM
The EZ-Link™ system enables the use of these optional Add-Ons:
Mach 4® Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AF720
Articulating Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AH720*
Brushcutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BC720*
Bladed Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BP720
Blower Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BT720*
Blower Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BV720
Garden Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720
Lawn Dethatcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .LD720
Lawn Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720*
Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS720
Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SS725
Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ST720
Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720
* Do NOT use this add-on with an electric powered product.
WARNING:
When using any add-on, read and understand
that add-on's specific manual before you begin operation.
Follow all applicable safety information.
Removing the Add-On
WARNING:
To avoid serious personal injury and damage to
the unit, shut the unit off before removing or installing add-ons.
1. Turn the knob counterclockwise to loosen (Fig. 16).
2. Press and hold the release button (Fig. 16).
EZ-Link™
Coupler
3. While firmly holding the upper shaft housing, pull the cutting attachment
or add-on straight out of the EZ-Link™ coupler (Fig. 17).
EZ-Link™ Coupler
Upper Shaft Housing
Installing the Add-On
NOTE: To make installing or removing the add-on easier, place the unit on
the ground or on a work bench.
1. Turn the knob counterclockwise to loosen (Fig. 16).
8
ASSEMBLY INSTRUCTIONS
Release
Button
Knob
Guide Recess
Fig. 16
Release Button
Primary Hole
Lower Shaft Housing
Fig. 17
2. While firmly holding the add-on, push it straight into the EZ-Link™
coupler (Fig. 17).
NOTE: Aligning the release button with the guide recess will help
installation (Fig. 16).
3. Turn the knob clockwise to tighten (Fig. 18).
CAUTION:
Lock the release button in the primary hole and
securely tighten the knob before operating this unit.
CAUTION:
Add-ons are to be used in the primary hole only.
Using the wrong hole could lead to personal injury or damage
to the unit.
For edging (when using the
line head cutting attachment
with EZ-Link™ models), lock
the release button of the
cutting attachment into the
90° edging hole (Fig. 18).
90˚ Edging Hole
(Trimmer Only)
Fig. 18
Knob